Search results for "Filler"

Kenaf-filled biodegradable composites: rheological and mechanical behaviour

2012

Biodegradable polymer composites, typically based on biodegradable polymer matrices and natural-organic fillers, are gaining rising interest and importance over the last few years. Several natural-organic fillers can be used but the most widespread so far is wood, in the form of fibres or flour. Alternative cellulosic fillers can ensure advantages in terms of resource utilization and properties of the final composite. In this work, Mater-Bi® based biodegradable composites were prepared with two kinds of wood flour, and directly compared with alternative composites containing kenaf fibres. The use of kenaf fibres allowed improved elastic modulus, tensile strength and interaction with the pol…

Recycling of the "light fraction" from municipal post-consumer plastics: Effect of adding wood fibers

1999

At present the recycling of plastic materials is mostly done using homogeneous polymers. Therefore a separation from a municipal collection of plastic objects is necessary before recycling operations. The easiest way of separation is by flotation in water, i.e. the separation of the different plastics based on the different densities with respect to water. This means that all the plastic materials are separated in a “light fraction” mostly of polypropylene and polyethylene and in a “heavy fraction” mainly of poly(vinyl chloride) (PVC) and poly(ethylene terephthalate). The recycling of the light fraction should, in principle, be easy because of the relative similarity of the chemical structu…

Improving the properties of polypropylene–wood flour composites by utilization of maleated adhesion promoters

2007

Polymer composites filled with natural organic fillers have gained a significant interest during the last few years, because of several advantages they can offer compared with properties of inorganic-mineral fillers. However, these composites (based, in most cases, on polyolefins) often show a reduction in some mechanical properties. This is mainly due to the problems regarding dispersion of the polar filler particles in the non-polar polymer matrix and their interfacial adhesion with polymer chains. In this work, polypropylene-wood flour composites were prepared and the effect of the addition of a maleated polypropylene was investigated. The two materials were compounded by an industrial c…

PBI-based composite membranes for polymer fuel cells

2010

Abstract In the present study poly(2,2-(2,6-pyridin)-5,5-bibenzimidazole) was used for the preparation of novel MEAs for high-temperature polymer fuel cells (HT-PEMFCs). We prepared hybrid materials with two types of silica fillers in order to increase the MEA performances using this polymer. The membranes were characterized in terms of their microstructure and thermal stability. Cell operation tests and Electrochemical Impedance Spectroscopy were used for the characterization of the MEAs. A maximum power density of about 80 mW cm−2 was obtained at 300 mA cm−2 by using an imidazole-modified silica filler. The EIS technique showed that the fillers chiefly help to reduce the charge transfer r…

Selection of novel geopolymeric mortars for sustainable construction applications using fuzzy topsis approach

2020

Construction is recognized as one of the most polluting and energy consuming industries worldwide, especially in developing countries. Therefore, Research and Development (R&amp

Viscoelastic properties of acid milk gel as affected by fat nature at low level

2005

International audience; The viscoelastic properties of acid milk gels containing small amounts of different fats were investigated. Skim milk was reconstituted from ultra low-heat skim milk powder and emulsions made with 2% (v/v) sunflower oil, olive oil, groundnut oil, or anhydrous milk fat using a pressure homogenizer. Acidification at 20 °C for 14 h to pH ∼4.6 was achieved by adding glucono-δ-lactone to the emulsion. Stress relaxation testing enabled determination of the firmness and the solid-like properties, i.e., elasticity. Regardless of the physical state of the fat, emulsion gels exhibited higher firmness than fat-free gels, despite the low fat level used. The firmness of the gels …

A Study on Acidification and Intercalation of Illite Clay Minerals and their Potential Use as a Filler in SPEEK Composite Membranes

2018

The acidification and intercalation of illite containing clays were studied for potential use as fillers for sulphonated poly (ether ether ketone) (SPEEK) composite membrane preparation and future proton exchange membrane fuel cells application. The acidification and dimethyl sulfoxide (DMSO) intercalation of illite clays have been studied by powder X-ray diffractometry, X-ray fluorescence spectrometry, and thermogravimetric analysis. SPEEK composite membranes were made with 1, 3 and 5% purified, acidified, DMSO intercalated clay fillers. SPEEK/clay composite membranes were characterized by proton conductivity, water uptake, and mechanical strength.

Therapeutic use of hyaluronic acid fillers in the treatment of corticosteroid-induced skin and subcutaneous atrophy

2016

Corticosteroid injection–related tissue atrophy might cause permanent skin and soft tissue deformities1 due to several factors, most importantly fibroblast inhibition and decreased Type I collagen synthesis. Correction of these deformities is challenging and is mostly based on volume replacement with lipofilling or other methods. Clinical observations and research have shown that injection of stabilized hyaluronic acid (HA) induces collagen synthesis, partially restoring dermal matrix components, and eventually producing a permanent effect.2–5 Based on these data, we hypothesize that HA injections might successfully treat atrophic tissue changes caused by corticosteroid injection. We descri…

Complications of botulinum toxin and fillers: A narrative review

2019

Background Cosmetic surgery and esthetic procedures have become a billion dollar industry owing to the ever-growing demand of the population to stay young. The injectable treatments including fillers and botulinum toxin have become highly popular because of their quick, predictable and lasting results in the management of facial wrinkles and rejuvenation. Although these treatment modalities are relatively safe, they are associated with certain side effects. Aims In this review, we will focus on the complications of fillers and botulinum toxin. Patients/methods The literature research considered published journal articles (clinical trials or scientific reviews). Studies were identified by se…

Interazioni tra nanotubi e molecole organiche

Nell'ampio scenario dei nanomateriali, i sistemi nanotubolari godono di un consolidato e crescente interesse sia nell'ambito scientifico che industriale. Fra la miriade di sistemi tubolari, i più utilizzati sono i nanotubi a base di carbonio e carbon nanohorns e più recentemente, vista l'elevata biocompatibilità e il loro basso costo, nanotubi inorganici quali i nanotubi di allosite. la funzionalizzazione di questi materiali con diverse tipologie di molecole organiche, ha permesso la sintesi di materiali che potrebbero o hanno trovato applicazione come filler polimerici, come supporti eterogenei in catalisi e nel campo del drug carrier e delivery. Inoltre, nel caso di nanotubi di allosite, …