Search results for "Fluid dynamics"
showing 10 items of 1005 documents
On some issues in the computational modelling of spacer-filled channels for membrane distillation
2017
Abstract This study addresses issues which arise in the computational and experimental modelling of flow and heat/mass transfer in membrane distillation and other processes adopting spacer-filled channels (either planar or spiral wound), but have not been sufficiently clarified in the literature so far. Most of the argumentations presented are based on original computational results obtained by the authors by finite volume simulations; some literature results are also considered. The questions addressed regard the choice of scales for the reduction of data and the definition of dimensionless numbers ( Re , f , Nu , Sh ); the definition of average heat or mass transfer coefficients; the comb…
CFD prediction of flow, heat and mass transfer in woven spacer-filled channels for membrane processes
2021
Abstract Flow and heat or mass transfer in channels provided with woven spacers made up of mutually orthogonal filaments were studied by Computational Fluid Dynamics. The problem addressed was the combined effect of the parameters that characterize the process: pitch to height ratio P/H (2, 3 and 4), flow attack angle θ (0, 7, 15, 20, 30, 40 and 45°) and Reynolds number Re (from ~1 to ~4000). The Prandtl number was 4.33, representative of water at ~40°C, while the Schmidt number was 600, representative of NaCl solutions. Simulations were performed by the finite volume code Ansys CFX™ 18.1 using very fine grids of ~6 to ~14 million volumes. For Re > ~400, the SST turbulence model was used to…
CFD Investigation of Spacer-Filled Channels for Membrane Distillation
2019
The membrane distillation (MD) process for water desalination is affected by temperature polarization, which reduces the driving force and the efficiency of the process. To counteract this phenomenon, spacer-filled channels are used, which enhance mixing and heat transfer but also cause higher pressure drops. Therefore, in the design of MD modules, the choice of the spacer is crucial for process efficiency. In the present work, different overlapped spacers are investigated by computational fluid dynamics (CFD) and results are compared with experiments carried out with thermochromic liquid crystals (TLC). Results are reported for different flow attack angles and for Reynolds numbers (Re) ran…
Pressure drop at low reynolds numbers in woven-spacer-filled channels for membrane processes: CFD prediction and experimental validation
2017
The energy consumption due to pumping power is a crucial issue in membrane processes. Spacers provide mechanical stability and promote mixing, yet increasing pressure drop. Woven spacers and their behaviour at low Reynolds numbers are less studied in the literature. Nevertheless, they are typical of some membrane technologies, as reverse electrodialysis (RED). RED is a promising technology for electric power generation by the chemical potential difference of two salt solutions within a stack equipped by selective ion-exchange membranes. The mechanical energy required for pumping the feed solutions, can dramatically reduce the net power output. In this work computational fluid dynamics (CFD)…
Experimental and computational investigation of heat transfer in channels filled by woven spacers
2017
Abstract Models of woven-type spacer-filled channels were investigated by Computational Fluid Dynamics (CFD) and parallel experiments in order to characterize the performance of Membrane Distillation (MD) modules. The case of overlapped spacers was analysed in a companion paper. Experiments were based on a non-intrusive technique using Thermochromic Liquid Crystals (TLC) and digital image processing, and provided the distribution of the local convective heat transfer coefficient on a thermally active wall. CFD simulations ranged from steady-state conditions to unsteady and early turbulent flow, covering a Reynolds number interval of great practical interest in real MD applications. A specif…
Investigation of heat transfer in spacer-filled channels by experiments and direct numerical simulations
2016
Abstract The analysis of flow fields and heat or mass transfer phenomena is of great importance in the optimum design of spacer-filled channel geometries for a variety of membrane-based processes. In the present work, models of spacer-filled channels often adopted in Membrane Distillation are simultaneously investigated by experiments and Computational Fluid Dynamics (CFD). Experiments rely on a non-intrusive technique, based on the use of Thermochromic Liquid Crystals (TLC) and digital image processing, and provide the local distribution of the convective heat transfer coefficient on a thermally active wall. CFD relies on steady-state (laminar flow) simulations in the lower end of the Reyn…
Performance comparison between overlapped and woven spacers for membrane distillation
2017
The sustainable production of freshwater from seawater desalination is receiving increasing attention. Recently, some desalination technologies are taking advantage from the coupling with renewable resources; among them, membrane distillation (MD) is one of the most promising since it can be easily powered by low-grade thermal energy. MD being an emerging technology, efforts are required to optimize geometry and operating conditions of real units in order to reduce the unitary freshwater production cost. In particular, temperature polarization is a well-known detrimental effect for the process driving force; spacers are traditionally used to enhance mixing and make temperature boundary laye…
Power Consumption in Uncovered Unbaffled Stirred Tanks: Influence of the Viscosity and Flow Regime
2013
Notwithstanding the increasing industrial interest toward unbaffled tanks, available experimental information on their behavior is still scant, even for basic quantities such as the mechanical power drawn. In this work, the influence of the Reynolds and Froude numbers on the power consumption characteristics is presented for unbaffled stirred tanks operating both in nonaerated conditions (subcritical regime) and in aerated conditions (supercritical regime), i.e., when the free surface vortex has reached the impeller and the gas phase is ingested and dispersed inside the reactor. Experimental results obtained at various liquid viscosities show that power numbers obtained in subcritical condi…
CFD Simulation of Particle Suspension Height in Stirred Vessels
2004
Computational fluid dynamics (CFD) simulation capabilities for stirred solid–liquid dense systems are explored. These systems may give rise to the formation of a thick and well defined clear liquid layer in the upper part of the vessel, whose extension progressively reduces with increasing impeller speed. Experimental measurements of the suspension height (the height of the particle laden layer) were carried out at various agitation speeds for a variety of solid–liquid systems in a fully baffled transparent tank. A clear layer of liquid was actually observed in all runs, with the suspension height almost linearly dependent on agitation speed. CFD simulations of the above described systems w…
CFD modelling of profiled-membrane channels for reverse electrodialysis
2014
Abstract: Reverse electrodialysis (RE) is a promising technology for electric power generation from controlled mixing of two differently concentrated salt solutions, where ion-exchange membranes are adopted for the generation of ionic currents within the system. Channel geometry strongly influences fluid flow and thus crucial phenomena such as pressure drop and concentration polarization. Profiled membranes are an alternative to the more commonly adopted net spacers and offer a number of advantages: avoiding the use of non-conductive and relatively expensive materials, reducing hydraulic losses and increasing the active membrane area. In this work, Computational Fluid Dynamic simulations we…