Search results for "Forensic"
showing 10 items of 1701 documents
Mechanical recycling of polylactide, upgrading trends and combination of valorization techniques
2016
[EN] The upcoming introduction of polylactides in the fractions of polymer waste encourages technologists to ascertain its valorization at the best quality conditions. Mechanical recycling of PLA represents one of the most cost-effective methodologies, but the recycled materials are usually directed to downgraded applications, due to the inherent thermomechanical degradation affecting its mechanical, thermal and rheological performance. In this review, the current state of mechanical recycling of PLA is reported, with special emphasis on a multi-scale comparison among different studies. Additionally, the applications of physical and chemical upgrading strategies, as well as the chances to b…
The effects of surgical preparation techniques and implant macro-geometry on primary stability : an in vitro study
2016
Background The attainment of a good primary stability is a necessary condition to ensure the success of osseointegration in implantology. In type IV cancellous bone, however, it is possible that a reduced primary stability can lead to an increased rate of failure. The aim of this study was therefore to determine, with the help of the resonance frequency (Osstell mentor), which technique of implant site preparation (piezo surgery, conventional, under-preparation, bone compaction, osteodistraction) and macro-geometry is able to improve implant stability in type IV cancellous bone. Material and Methods 10 pig ribs were prepared with a surgical pre-drilled guide, calibrated for a correct implan…
Strength distribution in paper
1998
Abstract Tensile strength distributions are studied in four paper samples that exhibit a variety of brittle-to-ductile properties. 1005 tensile specimens were measured in each case. The standard Gumbel and Weibull distributions, and a recently proposed double exponential modification of the former are compared with the observations visually and using chi-squared and Kolmogorov–Smirnov tests. The Gumbel distribution fails to fit the data while the Weibull distribution gives satisfactory agreement. However, the double exponential distribution fits the data best, regardless of the ductility of the material.
Investigation and modeling of the anomalous yield point phenomenon in pure tantalum
2014
International audience; The monotonic and cyclic behavior of commercially pure tantalum has been investigated at room temperature, in order to capture and understand the occurrence of the anomalous yield point phenomenon. Interrupted tests have been performed, with strain reversals (tensile or compressive loading) after an aging period. The stress drop is attributed to the interactions between dislocations and solute atoms (oxygen) and its macroscopic occurrence is not systematically observed. InfraRed Thermography (IRT) measurements supported by Scanning Electron Microscopy (SEM) pictures of the polished gauge length of a specimen during an interrupted tensile test reveal the nucleation an…
Multi-Module vs. Single-Module concept: Comparison of thermomechanical performances for the DEMO Water-Cooled Lithium Lead breeding blanket
2018
Abstract Within the framework of EUROfusion R&D activity an intense research campaign has been performed at the University of Palermo, in close cooperation with ENEA labs and KIT, in order to compare the thermomechanical performances of the Back Supporting Structure (BSS) of Multi-Module and Single-Module concepts of DEMO Water-Cooled Lithium Lead breeding blanket (WCLL). To this purpose, detailed 3D models of the DEMO WCLL right inboard and central outboard segments, including detailed BSS and simplified First Wall and structures according to the two concepts, have been set-up. The study has been performed considering the Normal Operation and Central Major Disruption steady state loading s…
Elastic configurations of self-supported oxide membranes for fuel cells
2013
Abstract Ultra-thin oxide films are of interest in energy conversion technologies such as low temperature solid oxide fuel cells and permeation membranes. Understanding their thermo-mechanical stability is an important problem. Edge clamped, self-supported thin film membranes show hierarchical wrinkles; with the largest wavelengths in the center, while smaller ones arise near the clamped boundary; correspondingly the largest strains, with tensile stress comparable to the residual stress, are in the vicinity of the clamped boundary. Our results can be understood by simple scaling arguments and are valid for membranes in the post-buckling regime far from threshold. We confirm the validity of …
Evaluation of Subgrade Resilient Modulus Predictive Model for Use in Mechanistic-Empirical Pavement Design Guide
2006
The characterization of unbound materials in the mechanistic–empirical pavement design guide (MEPDG), also known as the 2002 design guide, is reviewed, and this characterization is applied to Minnesota subgrades. The main emphasis is on the collection of k1-, k2-, and k3-parameters for Minnesota fine-grained soils and the procedure for the interpretation of the resilient modulus test to provide an input to the multilayer elastic theory (MLET) analysis (Level 2 input). This is an important aspect of adaptation of the MEPDG, because the guide recommends measurement of resilient moduli from laboratory testing, but the procedure does not specify how to interpret the test data to obtain an input …
Advantages of fitting contrast curves using logistic function: a technical note.
2013
Objective The aim of this article is to demonstrate how the contrast properties of an imaging system can be ideally fitted with the use of stripe patterns and the logistic function. Study Design Stripe patterns with defined amounts of line pairs (lp/mm) per mm (10-20 lp/mm) were recorded with the use of digital photostimulable storage phosphor. Scan data and normalized image data were analyzed with the use of ImageJ and MatLab to calculate different contrast curves. Results For original scan data, the goodness of fit was 0.0000019 (sum of squared error [SSE]). The R-square was 0.9998. For normalized data the goodness of fit was 0.0007 (SSE) and the R-square 0.998. An amount of 50% contrast …
La matriz extracelular: morfología, función y biotensegridad (parte I)
2009
La matriz extracelular (MEC) representa una red tridimensional que engloba todos los órganos, tejidos y células del organismo. Constituye un filtro biofísico de protección, nutrición e inervación celular y el terreno para la respuesta inmune, angiogénesis, fibrosis y regeneración tisular. Y representa el medio de transmisión de fuerzas mecánicas a la membrana basal, que a través de las integrinas soporta el sistema de tensegridad y activa los mecanismos epigenéticos celulares. La alteración de la MEC supone la pérdida de su función de filtro eficaz, nutrición, eliminación, denervación celular, pérdida de la capacidad de regeneración y cicatrización y alteración de la transmisión mecánica o …
Involvement of the cholinergic basal forebrain nuclei in spinocerebellar ataxia type 2 (SCA2)
2013
Aims: Spinocerebellar ataxia type 2 (SCA2) belongs to the CAG repeat or polyglutamine diseases. Along with a large variety of motor, behavioural and neuropsychological symptoms the clinical picture of patients suffering from this autosomal dominantly inherited ataxia may also include deficits of attention, impairments of memory, as well as frontal-executive and visuospatial dysfunctions. As the possible morphological correlates of these cognitive SCA2 deficits are unclear we examined the cholinergic basal forebrain nuclei, which are believed to be crucial for several aspects of normal cognition and may contribute to impairments of cognitive functions under pathological conditions. Methods: …