Search results for "Friction"

Resistance to water and abrasion of a broad-spectrum sunscreen: a prospective, open-label study.

2015

Caratterizzazione microstrutturale e meccanica di giunti friction skin-stringer (2024/t4-7075/t6) saldati a basso e alto apporto termico

2011

Fatigue resistance of AA2024-T4 friction stir welding joints: Influence of process parameters

2005

Material flow and CDRX phenomena determining joint resistance in AA7075-T6 friction stir welding

2006

Feasibility of using more polishable aggregates in dense-graded asphalt surface mixture: Case study of dolomite

2022

This study aimed to evaluate the feasibility of using more dolomite aggregates in asphalt surface mixtures that are typically used by West Virginia Division of Highways (WVDOH). The laboratory test results indicated that increasing dolomite content in asphalt surface mixtures resulted in a faster deterioration rate at the early polishing stage. In addition, asphalt surface mixtures containing more than 50% dolomite coarse aggregates would significantly reduce roadway safety. The field test results validated that dolomite shall not exceed 50% of coarse aggregate in asphalt surface mixture if the projected traffic volume is greater than 3.0 million equivalent single axle loads (ESALs).

BE contact analysis of delamination cracks actively repaired trhough piezoelectric active patches

2009

New mesh shape and improved implantation procedure to simplify and standardize open ventral hernia repair: a preliminary report.

2010

Introduction Issues in ventral hernia repair are represented by the need for mesh fixation and how to assure a sufficient mesh overlap of the defect. Aiming to resolve these problems, this study describes a modified technique for ventral and incisional hernia repair based upon a newly developed mesh with a special design. This new type of implant allows broader coverage of the abdominal wall and results in tension- and fixation-free repair. Materials and methods A unique geometrically shaped mesh consisting of a large central body and radiating arms was used to repair ventral or incisional hernia. The mesh was intended not to be point-fixated. The friction of the straps passing through the …

Tentacle-shaped mesh for fixation-free repair of umbilical hernias

2019

Purpose: Mesh fixation and broad overlap represent an open issue in umbilical hernia repair. A proprietary-designed implant with tentacle straps at its boundary has been developed to ensure a suture-free repair and a broader coverage of the abdominal wall. The study describes the results of umbilical hernia procedures carried out with the tentacle-shaped implant and the related surgical technique. Methods: A proprietary tentacle-shaped flat mesh having a central body with integrated radiating arms at its edge was used to repair large umbilical hernias in 62 patients. The implant was placed in preperitoneal sublay. The friction of the straps, crossing the abdominal wall thanks to a special n…

Characterization of friction stir consolidated recycled billet by uniaxial compression tests with miniaturized cylindrical specimen

2023

Abstract. Friction stir consolidation (FSC) is a solid-state recycling method that directly converts machining scraps into semifinished billets. This process has been proven to be a more energy efficient and environmentally friendly technique compared to remelting based conventional recycling methods. During FSC, machining chips are transformed into a solid billet by the stirring action and friction heat of the rotating tool. Due to process mechanics, especially temperature gradient and strain rate, billets have shown different hardness values and grain size distribution across their sections. Therefore, in this research, miniaturized upsetting samples are extracted from the FSC billet. The…

Fabrication of Billet from Aluminum Alloys AA 2011-T3/7075 Chips through Friction Stir Consolidation

2022

Recently evolving Solid-State Recycling (SSR) techniques have shown promising features to recycle metals scraps more efficiently compared to remelting-based approaches. Among these SSR methods, Friction Stir Consolidation (FSC) has been successfully tested to transform metals chips directly into semi or final solid products. Therefore, researchers explored FSC critical process parameters and their subsequent effects on quality in terms of the mechanical and metallurgical properties of the billet. All the previous studies of FSC were limited to developing billet of mono materials. Therefore, in this research, an attempt was made to go beyond the idea of recycling; in fact, a billet of two di…