Search results for "Fuel Cell"

Impact of Ir modification on the durability of FeNC catalysts under start-up and shutdown cycle conditions

2022

A common problem associated with FeNC catalysts is their poor stability dominated by the carbon oxidation reaction (COR). In this work, the feasibility of stabilizing FeNC catalysts with small quantities of Ir was explored. With iridium being present, instead of COR the oxygen evolution reaction should be favored. The impact on structure and morphology was investigated by 57Fe Mössbauer spectroscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and transmission electron microscopy. The catalytic activity and durability for the oxygen reduction reaction was evaluated by rotating ring disc electrode experiments and accelerated stress tests mimicking the start-up and shutdown cycle (SS…

Ab initio thermodynamic study of (Ba,Sr)(Co,Fe)O3 perovskite solid solutions for fuel cell applications

2013

(Ba,Sr)(Co,Fe)O3 (BSCF) perovskite solid solutions are promising materials for solid oxide fuel cell cathodes and oxygen permeation membranes. Cathode performance strongly depends on the morphology of these materials remaining as a single phase or two-phase mixture. Combining ab initio calculations of the atomic and electronic structure of different supercells with thermodynamics of solid solutions, we have constructed and discussed phase diagrams of several important BSCF chemical compositions. It is demonstrated that in BSC cobaltite solid solution the spinodal decomposition may occur already at relatively low temperatures, while ferrite (BSF and SCF) solid solutions decompose at relative…

Characterisation of scheelite LaW0.16Nb0.84O4.08 ion conductor by combined synchrotron techniques: Structure, W oxidation state and interdiffusion

2021

Abstract Scheelite-type materials such as LaNbO4 are increasingly attracting attention as a possible alternative to the most common fluorite and perovskite structure as ion conductors. However, they are much less used and investigated. The introduction of tungsten in lanthanum orthoniobate leads to conduction properties that are compatible with oxygen ion conductivity. In this paper, we studied the effect of the introduction of tungsten in the LaNbO4 structure. High resolution X-ray diffraction showed that in LaNb1-xWxO4+x/2 with x = 0.16 the monoclinic distortion is largely suppressed and the tetragonal phase is predominant at room temperature. By XANES/EXAFS we proved that tungsten is in …

Influence of the Molecular Weight on PVA/GO Composite Membranes for Fuel Cell Applications

2020

Composite polymer electrolyte membranes were prepared with poly (vinyl alcohol) (PVA). Two different molecular weight (Mw), 67·103 and 130·103 g·mol−1 were selected, cross-linked with sulfosuccinic acid (SSA) and doped graphene oxide (GO). The effects on the membranes obtained from these polymers were characterized in order to evaluate the fuel cell performance. Electron microscopy showed a proper nanoparticle distribution in the polymer matrix. The chemical structure was evaluated by Fourier transform infrared spectroscopy. The absence of a crystalline structure and the enhancement on the thermal stability with the addition of 1% of GO was demonstrated by thermal characterization. Total tr…

Ionic Liquid Composite Polybenzimidazol Membranes for High Temperature PEMFC Applications

2019

A series of proton exchange membranes based on polybenzimidazole (PBI) were prepared using the low cost ionic liquids (ILs) derived from 1-butyl-3-methylimidazolium (BMIM) bearing different anions as conductive fillers in the polymeric matrix with the aim of enhancing the proton conductivity of PBI membranes. The composite membranes prepared by casting method (containing 5 wt. % of IL) exhibited good thermal, dimensional, mechanical, and oxidative stability for fuel cell applications. The effects of anion, temperature on the proton conductivity of phosphoric acid-doped membranes were systematically investigated by electrochemical impedance spectroscopy. The PBI composite membranes containin…

Performance analysis of single cell solid oxide fuel cells

2017

Solid oxide fuel cells (SOFCs) are a class of fuel cells operating on high temperatures which have the potential to become one of the efficient and cost effective system for direct conversion of a wide variety of fuels to electricity. For proper operation of SOFCs, evaluation of cell stability and optimization of fuel utilization is of paramount importance. In this paper, we have performed experiments to obtain current-voltage (I–V) characteristics by using three different Hydrogen (H 2 ) flow rates(100 ml/min, 150 ml/min and 200 ml/min). Furthermore, we perform oxidation and reduction (redox) cycles to determine how many redox cycles a SOFC can withstand without cracking the cell which we …

Metal Hydride-Based Hydrogen Storage Tank Coupled with an Urban Concept Fuel Cell Vehicle: Off Board Tests

2018

Study and design of a controlled oscillator for an embedded system to measure the complex impedance of PEM fuel cell »

2017

We present in this paper the study and the design of a voltage controlled oscillator (VCO) for an embedded system to diagnose the PEM fuel cell. Some problems related to fuel cells used in the electric vehicle field are the management of its efficiency and the lifetime of its membranes. To do this, the diagnosis using measuring the complex impedance is an important phase. It is based on the injection of a perturbation signal at the output of the PEM fuel cell, then we observe its behavior by measuring its impedance. The used measurement method is the electrochemical impedance spectroscopy (EIS) using the load modulation technique, which is implemented in an embedded measurement system based…

Opportunity of metallic interconnects for ITSOFC : Reactivity and electrical property.

2006

International audience; Iron-base alloys (Fe-Cr) are proposed hereafter as materials for interconnect of planar-type intermediate temperature solid oxide fuel cell (ITSOFC); they are an alternative solution instead of the use of ceramic interconnects. These steels form an oxide layer (chrornia) which protects the interconnect from the exterior environment, but is an electrical insulator. One solution envisaged in this work is the deposition of a reactive element oxide coating, that slows down the formation of the oxide layer and that increases its electric conductivity. The oxide layer, formed at high temperature on the uncoated alloys, is mainly composed of chromia; it grows in accordance …

Main Fuel Cells mathematical models: Comparison and analysis in terms of free parameters

2010

This paper resumes the main mathematical models of Fuel Cells (PEM models). In particular, a comparison study of the various models introduced in the technical literature is presented and the dependency of the various model parameters is analyzed in different operating conditions. As the manifold of the model parameter is very wide and their determination is difficult, it is mandatory to introduce approximations and simplifications on which each model is based. The novelty of this work is the organization of the existing models in three categories with regard to the number of free parameters and to the dependency of such parameters on the different running conditions and the usage of a refe…