Search results for "Fuel Technology"

Hydrothermal liquefaction of wood using a modified multistage shrinking-core model

2020

Abstract Wood liquefaction in hot compressed water is modeled using the hydrolysis of Cellulose, Hemicellulose, and Lignin. These three components are reacted under catalyst-free subcritical conditions in a temperature range from 553 K to 640 K, and the heating rate ranges from 2 K/min to 6 K/min. Using a simplified reaction scheme, water-soluble products 1 (WSP), Biocrude, char, and gas are generated through intermediates with each wood component. A modified multistage shrinking core model is employed to simulate biomass particle degradation. The reaction and kinetic regime of the hydrothermal liquefaction 2 (HTL) process are treated separately for each wood component. Although the lack of…

Effect of Ni content on the structure and hydrogenation property of mechanically alloyed TiMgNix ternary alloys

2017

Abstract In this study, TiMgNix samples (x = 0.2, 0.4, 0.6, 0.8, 1) have been prepared by mechanical alloying using a planetary high-energy ball mill. The structural transformations were characterized by XRD and indicated that all the as-milled TiMgNix alloys consist of mixtures of crystalline Mg and amorphous Ti-Ni-(Mg) phase. TEM analyses also show that nanocrystallites and amorphous phases coexist in the as-milled TiMgNi alloy. Electrochemical test shows that the TiMgNi composition yields the highest discharge capacity. The discharge capacities and activation properties of TiMgNix alloys linearly increase with increasing Ni content. The MgTiNi0.8 composition boasts the best cycling prope…

Coated interconnects development for high temperature water vapour electrolysis: Study in anode atmospher

2013

International audience; High temperature water vapour electrolysis (HTE) is an efficient technology for hydrogen production. In this context, a commercial stainless steel, K41X (AISI 441), was chosen as interconnect. In a previous paper, the high temperature corrosion and the electrical conductivity were evaluated in both anode (O-2-H2O) and cathode (H-2-H2O) atmosphere at 800 degrees C. In O-2-H2O atmosphere, the formation of a thin chromia protective layer was observed. Nevertheless, the ASR parameter measured was higher than the maximum accepted value. These results, in addition with chromium evaporation measurements, proved that the K41X alloy is not suitable for HTE interconnect applic…

Mechanism of co-pyrolysis of coal-tar pitch with polyacrylonitrile

2003

Abstract Co-pyrolysis of coal-tar pitch with polyacrylonitrile (PAN) and PAN oxidized in air at 300 °C was studied as a possible way of manufacturing of carbonaceous materials enriched in nitrogen. The thermal behaviour of components and blends was evaluated by thermogravimetry and optical microscopy of solid residues. The transformation of nitrogen functional groups on co-treatment was monitored using elemental analysis, infrared spectroscopy and X-ray photoelectron spectroscopy. Oxidized polymer behaved as an inert during co-pyrolysis. In contrast, strong interactions of unoxidized PAN with pitch could be deduced from enhanced residue yield and extensive deterioration of the optical textu…

Efficient Vacuum-Deposited Perovskite Solar Cells with Stable Cubic FA 1– x MA x PbI 3

2020

Preparation of black formamidinium lead iodide (FAPbI3) requires high temperature annealing and the incorporation of smaller A-site cations, such as methylammonium (MA+), cesium or rubidium. A major advantage of vacuum processing is the possibility to deposit perovskite films at room temperature (RT), without any annealing step. Here we demonstrate stabilization of the cubic perovskite phase at RT, in a three-sources co-sublimation method. We found that the MA+ incorporation is a self-limiting process, where the amount of MA+ which is incorporated in the perovskite is essentially unvaried with increasing MAI deposition rate. In this way a phase-pure, cubic perovskite with a bandgap of 1.53 …

Efficient Wide-Bandgap Mixed-Cation and Mixed-Halide Perovskite Solar Cells by Vacuum Deposition

2021

Vacuum deposition methods are increasingly applied to the preparation of perovskite films and devices, in view of the possibility to prepare multilayer structures at low temperature. Vacuum-deposited, wide-bandgap solar cells based on mixed-cation and mixed-anion perovskites have been scarcely reported, due to the challenges associated with the multiple-source processing of perovskite thin films. In this work, we describe a four-source vacuum deposition process to prepare wide-bandgap perovskites of the type FA1-n Cs n Pb(I1-x Br x )3 with a tunable bandgap and controlled morphology, using FAI, CsI, PbI2, and PbBr2 as the precursors. The simultaneous sublimation of PbI2 and PbBr2 allows the…

Strontium and iron-doped barium cobaltite prepared by solution combustion synthesis: exploring a mixed-fuel approach for tailored intermediate temper…

2013

Ba0.5Sr0.5Co0.8Fe0.2O3-? (BSCF) powders were prepared by solution combustion synthesis using single and double fuels. The effect of the fuel mixture on the main properties of this well-known solid oxide fuel cell cathode material with high oxygen ion and electronic conduction was investigated in detail. Results showed that the fuel mixture significantly affected the area-specific resistance of the BSCF cathode materials, by controlling the oxygen deficiency and stabilizing the Co2+ oxidation state. It was demonstrated that high fuel-to-metal cations molar ratios and high reducing power of the combustion fuel mixture are mainly responsible for the decreasing of the area-specific resistance o…

Correction to Overview and Essentials of Biomass Gasification Technologies and Their Catalytic Cleaning Methods

2017

New insight on the lithium hydride–water vapor reaction system

2018

Abstract The reaction of lithium hydride (LiH) powder with pure water vapor (H2O and D2O) was studied by thermogravimetry and in situ infrared spectroscopy at 298 K over a large pressure range. The mean particle size of LiH is around 27 μm. At very low pressure, the hydrolysis starts with the formation of lithium oxide (Li2O). Then, both Li2O and lithium hydroxide (LiOH) are formed on increasing pressure, thus, creating a Li2O/LiOH bilayer. The reaction takes place through the consumption of LiH and the formation of Li2O at the LiH/Li2O interface and through the consumption of Li2O and the formation of LiOH at the Li2O/LiOH interface. Above 10 hPa, only the monohydrate LiOH·H2O is formed. T…

Improvement in the performance of low temperature H2-O2 fuel cell with chitosanephosphotungstic acid composite membranes

2016

Abstract Free-standing chitosan/phosphotungstic acid polyelectrolyte membranes, prepared by ionotropic gelation on alumina porous supports, were employed as proton conductor in low temperature H 2 –O 2 fuel cell. A drying step on glass substrate was introduced in the fabrication procedure to reduce shrinkage and consequent corrugation. Membranes were tested with electrodes prepared according to different procedures and with two different Pt loadings, namely 0.5 and 1 mg cm −2 . Both the investigated kinds of electrodes allowed to get very promising power peaks of 550 mW cm −2 in spite of the different Pt content. The polarization curves and the electrochemical impedance spectra suggest that…