Search results for "Glass fiber"
showing 10 items of 66 documents
A Certain Mathematical Model of the Glass Fibre Material Production
1997
There is considered the full mathematical model of chemical reactions on the surface of glass fibre material that was imbedded in the flow of acid solution and was pulled longitudionally. Self-similar forms of this model are obtained and their approximations by monotone schemes of differences are proposed. Some special cases which make possible to get the analytic solutions are underlined. The self-similar forms of the differential equations of the substances transport allow to calculate the emission of the alkaline oxide from the glass fibre material under the influence of the acid solution flow. Some conclusions with practical significance for the technological process is made up accordin…
A model of oil burnout from glass fabric
1997
A mathematical model is proposed for the process of the removal (by burning) of oil contained in a glass fibre insulation fabric manufactured in Latvia. The small aspect ratio of the fabric allows simplifications to the modelling which reduce the problem to a single nonlinear ordinary differential equation. When the effects of reflected radiation are also included, the differential equation is supplemented by two integral equations. Predictions of the position of the ‘burning zone’ accord well with observations made at the factory. The effect of the inclusion of extra heating chambers is also examined, and it is found that the temperature gradient in the fabric may be greatly decreased in t…
A Comparative Study of Natural Fiber and Glass Fiber Fabrics Properties with Metal or Oxide Coatings
2015
Rapidly growing global demand for technical textiles industries is stimulated to develop new materials based on hybrid materials (yarns, fabrics) made from natural and glass fibres. The influence of moisture on the electrical properties of metal and metal oxide coated bast (flax, hemp) fibre and glass fibre fabrics are studied by electrical impedance spectroscopy and thermogravimetry. The bast fibre and glass fiber fabrics are characterized with electrical sheet resistance. The method for description of electrical sheet resistance of the metal and metal oxide coated technical textile is discussed. The method can be used by designers to estimate the influence of moisture on technical data of…
Influence de l'orientation des fibres sur un essai Arcan = Influence of fiber orientation on Arcan test data
2009
National audience; Ce papier présente les résultats d'une étude expérimentale portant sur le comportement d'éprouvettes ‘papillon' en verre/époxy, soumises à des chargements de cisaillement pur et de traction-cisaillement combinés, au moyen d'un dispositif Arcan. Des éprouvettes dont les fibres sont orientées parallèlement à la direction des entailles et d'autres pour lesquelles les fibres sont perpendiculaires à cette direction, respectivement désignées Mat31 et Mat32, ont été testées pour différents angles de sollicitation, dans une plage comprise entre 0° et 90°. Le mode de rupture observé pour les éprouvettes Mat31 est répétitif, alors qu'il dépend de la direction de la sollicitation po…
Characterization of a fiber-reinforced new fully aromatic liquid crystalline polymer
1998
A new rigid liquid crystalline polymer that demonstrates good mechanical and thermomechanical properties and acceptable processing temperature has been recently synthesized and characterized. The melting temperature and some thermomechanical properties do not seem, however, suitable for use in some applications at high temperature or in the presence of aggressive fluids. The use of appropriate inorganic fillers can overcome these shortcomings. In this work the new LCP, polymerized in a bench-scale apparatus, and the same sample filled with carbon fibers are characterized. The properties of the carbon fiber filled LCP are compared with those of another filled wholly aromatic commercial LCP,…
Prediction method of electrical conductivity of nano-modified glass fibre reinforced plastics
2019
Glass fibre reinforced plastics (GFRP) is non-conductive construction material, however with carbon nanotubes (CNT) modifying it can get additional functionality due to its gained electrical conductivity. Main aim of the study is to check functionality of the prediction method of electrical conductivity of GFRP with nano-modified epoxy matrix using structural approach. GFRP composites under investigation were based on unidirectional (UD) Glass fiber and two matrixes modified with carbon nanotubes. Electrical conductivity of epoxy resin modified by CNT (concentrations < 1%) was modelled using structural approach. Electrical conductivity of unidirectional GFRP layer was measured experimentall…
Strain rate effect in the single-fiber-fragmentation test
2001
The single fiber fragmentation test (SFFT) has been widely used to characterize the interface in fiber-reinforced polymers. The purpose of the work reported here was to determine the effect of strain rate on the fiber fragment lengths obtained in the SFFT. Three materials systems were used to make single-fiber-composite specimens: E-glass fiber/polycarbonate matrix, AS4-carbon fiber/polycarbonate matrix, and AU4-carbon fiber/polycarbonate matrix. The fiber-matrix adhesion in all three systems is based on physisorption rather than chemisorption. Each system was tested at strain rates ranging over four orders of magnitude. Results are reported in terms of fragment length, the dependent variab…
Dependence of Coefficient of volumetric thermal expansion (CVTE) of glass fiber reinforced (GFR) polymers on the glass fiber content
2007
In a Glass Fiber Reinforced (GFR) polymer, the coefficient of volumetric thermal expansion CVTE (determined as a sum of the coefficients of linear thermal expansion CLTE’s for the three principal directions) is sometimes much smaller than the value predictable on the basis of well acquainted models, such as Chow model, taking into account fibers anisotropy and aspect ratio.
Indentation test as a tool for monitoring the solidification process during injection molding
2003
An inline method for monitoring the solidification process during the injection molding of semicrystalline polymers is demonstrated. The method has been applied to various poly(ethylene terephthalate) (PET) and poly(buthylene terephthalate) (PBT) samples. The technique is based on a simple device by which an additional ejector pin is pushed onto the injection-molded part with a fixed force at different times during the solidification phase while the mold remains closed. The residual deformation (the so-called indentation depth) due to the applied load is measured offline after ejection. By the performance of indentation at different times during the cooling phase, an indentation depth profi…
Effects of filler type and mixing method on the physical properties of a reinforced semirigid liquid crystal polymer
1996
Semirigid liquid crystalline polymers (LCPs) show some advantages with respect to rigid LCP: in particular lower processing temperatures, better compatibility with flexible thermoplastics, but also some disadvantages. Thermal resistance of rigid LCPs is much better and the maximum working temperature is, in general, very high. The thermomechanical properties can be improved by adding inorganic fillers. In this work processing, mechanical and thermomechanical properties of a filled semirigid liquid crystal copolyester are reported. Several inorganic fillers have been used in order to put in evidence the influence of shape and dimensions of the particles on the properties of the filled materi…