Search results for "Glass"
showing 10 items of 1153 documents
Mechanical relaxation in miscible polymer systems: the glass transition regime in poly(vinylmethylether) (PVME)-cross-polystyrene (PS) semi-interpene…
1990
Abstract Miscible semi-interpenetrating polymer networks (semi-IPN) of varying composition are prepared by crosslinking polystyrene containing few maleic anhydride groups with a diamine in the presence of linear poly(vinylmethylether) (PVME). The resulting PVME-c-P(ScoMA) semi-IPNs are characterized by their thermal and thermomechanical behaviour. Comparison with the corresponding uncrosslinked material proves that weak crosslinking has a negligible effect on the location of the glass transition as measured by d.s.c. Both the Tg data and the temperatures of the loss modulus maximum E″ (at 1 rad/s) show the same non-linear curved composition dependence. Contrary to this the tan δ maximum var…
Excess viscosity and glass transition
2001
Abstract Literature data on the viscosity of solutions of poly(butyl methacrylate) (PBMA) and poly(methyl methacrylate) (PMMA) in diethyl phthalate (DEP) for different temperatures, including the range around and below T g , the glass transition temperatures of the pure polymers, were evaluated by means of an approach that uses surface fractions as composition variables. The discussion of these results together with information on solutions of the isomeric polymers, poly(vinyl acetate) (PVAc) and poly(methyl acrylate) (PM(A)), in the same solvent testifies that the previously published relations remain valid for T T g . They enable the determination of viscosities of the pure polymers below…
Effects of filler type and mixing method on the physical properties of a reinforced semirigid liquid crystal polymer
1996
Semirigid liquid crystalline polymers (LCPs) show some advantages with respect to rigid LCP: in particular lower processing temperatures, better compatibility with flexible thermoplastics, but also some disadvantages. Thermal resistance of rigid LCPs is much better and the maximum working temperature is, in general, very high. The thermomechanical properties can be improved by adding inorganic fillers. In this work processing, mechanical and thermomechanical properties of a filled semirigid liquid crystal copolyester are reported. Several inorganic fillers have been used in order to put in evidence the influence of shape and dimensions of the particles on the properties of the filled materi…
Influence of the cross-linking density on the main dielectric relaxation of poly(methyl acrylate) networks.
2005
A series of polymer networks of varying cross-linking density was prepared by copolymerization of methyl acrylate and ethyleneglycol dimethacrylate. The aim of this work is to study the influence of cross-linking on the conformational mobility of the polymer chains using dielectric relaxation spectroscopy (DRS) in the temperature range of the main dielectric relaxation. As expected, the temperature range in which glass transition takes place became wider with increasing crosslinking density. DRS results were analyzed using the Havriliak-Negami equation. Master Cole-Cole arcs could be drawn for all the networks. The arcs become more symmetric as cross-linking density increases, as a conseque…
Isobornyl Methacrylate as a Reactive Solvent of Polyethylene
2004
Solutions containing 15 wt, -% of a low-molar-mass polyethylene (PE) in isobornyl methacrylate (IBoMA), containing 0, 5 or 10 wt.-% of 1,4 butanediol dimethacrylate (BDDMA) as crosslinker, were polymerized using either benzoyl peroxide (BPO), at 80°C, or dicumyl peroxide (DCPO), with a thermal cycle attaining 150°C, as initiators. Phase separation of an amorphous PE-rich phase took place when carrying out the reaction at temperatures higher than the PE melting temperature. Partial crystallization of PE was observed when cooling to room temperature. Depending on the initial amount of BDDMA, the fraction of PE that was phase separated varied between 57 and 66% of the initial amount, with crys…
Sorption of n-hexane in amorphous polystyrene
2014
Sorption properties of pure n-hexane vapor in amorphous polystyrene (PS) were studied at 298 K by thermogravimetry under controlled vapor pressure. Two sorption-desorption cycles were performed by varying the relative pressure between 0 and 0.91. Mixing of PS with n-hexane resulted in a strong plasticization, which was evidenced by quite significant depression in the glass transition temperature of the polymer as shown by differential scanning calorimetry. Maximum quantity of n-hexane sorbed in the PS at 298 K and at a pressure close to saturation was about 12.4 wt %. The thermogravimetry yielded an isotherm with a strong hysteresis loop, explanation of which was hypothesized with the help …
Dielectric properties of a filled epoxy resin: Effect of thermal treatments
1982
Dielectric measurements have been performed at several frequencies on samples of a cycloaliphatic epoxy resin filled with aluminum hydroxide. The samples were thermally treated at three different temperatures for times up to 2,000 hours. At low aging temperatures and times an improvement of the characteristics is observed due perhaps to an assessment of the bulk of the polymer and more precisely to a change in the free volume. At high temperatures and times a thermo-oxidation involving layers deeper and deeper becomes the predominant mechanism responsible of the decrease in the properties with respect to the virgin material.
Reduction of the glass transition temperature in polymer films: A molecular-dynamics study
2001
We present results of molecular dynamics (MD) simulations for a non-entangled polymer melt confined between two completely smooth and repulsive walls, interacting with inner particles via the potential $U_{\rm wall}\myeq (\sigma/z)^9$, where $z \myeq |z_{\rm particle}-z_{\rm wall}|$ and $\sigma$ is (roughly) the monomer diameter. The influence of this confinement on the dynamic behavior of the melt is studied for various film thicknesses (wall-to-wall separations) $D$, ranging from about 3 to about 14 times the bulk radius of gyration. A comparison of the mean-square displacements in the film and in the bulk shows an acceleration of the dynamics due to the presence of the walls. %Consistent…
Relaxation processes and glass transition of confined polymer melts: A molecular dynamics simulation of 1,4-polybutadiene between graphite walls.
2017
Molecular dynamics simulations of a chemically realistic model for 1,4-polybutadiene in a thin film geometry confined by two graphite walls are presented. Previous work on melts in the bulk has shown that the model faithfully reproduces static and dynamic properties of the real material over a wide temperature range. The present work studies how these properties change due to nano-confinement. The focus is on orientational correlations observable in nuclear magnetic resonance experiments and on the local intermediate incoherent neutron scattering function, Fs(qz, z, t), for distances z from the graphite walls in the range of a few nanometers. Temperatures from about 2Tg down to about 1.15Tg…
Monte Carlo simulation of the glass transition in polymer melts: An application of MCT
1995
Abstract This paper reviews the results of a large scale Monte Carlo simulation for the dynamics of a supercooled polymer melt. The dynamics of the melt was studied by means of the time evolution of the incoherent intermediate scattering function φs q(t), which was monitored over seven decades in time. In an intermediate time window it is possible to describe the decay of φs q(t) quantitatively in the framework of mode-coupling theory, provided the extended version of the theory is used.