Search results for "Glass"

Polymer Dynamics in a Polymer-Solid Interphase: Molecular Dynamics Simulations of 1,4-Polybutadiene At a Graphite Surface

2014

A chemically realistic model of 1,4-polybutadiene confined by graphite walls in a thin film geometry was studied by molecular dynamics simulations. The chemically realistic approach allows for a quantitative determination of a variety of experimentally accessible relaxation functions (e.g., dielectric, NMR, or neutron scattering responses). The simulations yield these experimental observables. Additionally, the simulations can be resolved as a function of distance to the solid interface on a much finer scale than experimentally possible, providing a detailed mechanistic picture of the segmental and large scale motions of polymers in the interfacial region between bulk polymer melts and soli…

Prediction method of electrical conductivity of nano-modified glass fibre reinforced plastics

2019

Glass fibre reinforced plastics (GFRP) is non-conductive construction material, however with carbon nanotubes (CNT) modifying it can get additional functionality due to its gained electrical conductivity. Main aim of the study is to check functionality of the prediction method of electrical conductivity of GFRP with nano-modified epoxy matrix using structural approach. GFRP composites under investigation were based on unidirectional (UD) Glass fiber and two matrixes modified with carbon nanotubes. Electrical conductivity of epoxy resin modified by CNT (concentrations < 1%) was modelled using structural approach. Electrical conductivity of unidirectional GFRP layer was measured experimentall…

Spatial scale-dependent tracer diffusion in bulk polycarbonate studied by holographic relaxation.

2005

The diffusion of a photochromic dye tracer in polycarbonate was studied by a holographic relaxation technique (forced Rayleigh scattering) at temperatures close to the glass transition temperature. By varying the holographic grating period the results could be interpreted via the spatial scale dependence of apparent diffusion coefficients within a two-state diffusion model. This indicates inhomogeneities on the scale of a few micrometers in the polymer glass.

1993

4-(4-Carboxyphenyl)-3,5-dioxo-1,2,4-triazolidin-1-yl moieties resulting from 4-(3,5-dioxo-1,2,4-triazolin-4-yl)benzoic acid (U4A) randomly attached to 1,4-polybutadiene form supramolecular aggregates which act as effective junction zones in new thermoplastic elastomers. Deuteron nuclear magnetic resonance (2H NMR) spectroscopy was used to investigate the molecular dynamics of the polymer backbone and the junction zones in selectively labelled samples. The spectra show motional heterogeneity along the polymer chain as well as in the supramolecular domains. Polybutadiene segments which are adjacent to these polar clusters are restricted in their mobility, even at temperatures 100 K above the …

NLO-polymers containingtert-butyloxycarbonyl protecting groups: Modification after processing leading to thermally stable nonlinear optical materials

1997

Influence of the modification, induced by zirconia nanoparticles, on the structure and properties of polycarbonate

2013

Melt compounding was used to prepare polycarbonate (PC)–zirconia nanocomposites with different amounts of zirconia. The effect of the zirconia loading, in the range of 1–5 wt.%, on the structure, mechanical properties and thermal degradation kinetics was investigated. The zirconia nanoparticle aggregates were well dispersed in the PC matrix and induced the appearance of a local lamellar order in the polycarbonate as inferred by SAXS findings. This order could be a consequence of the intermolecular interactions between zirconia and the polymer, in particular with the quaternary carbon bonded to the methyl groups and the methyl carbon as inferred from the NMR results. The presence of zirconia…

Methylcellulose-Based Edible Films and Coatings:  2. Mechanical and Thermal Properties as a Function of Plasticizer Content

1997

Several edible films based on methylcellulose and polyethylene glycol 400 (PEG400) were prepared and stored until equilibration at different relative humidities. Tensile stress−strain curves show very different behaviors as a function of PEG400 and relative humidity. Tensile strength strongly depends on relative humidity and then on water content, more than on PEG400 content. On the contrary, elongation is dependent both on water and PEG400. These differences correspond to the glass transition of the polymer, which affects the elongation more than the tensile strength. However, from DSC measurements, it appears that the PEG400 has no or a very low compatibility with the methylcellulose matr…

Neutron reflectometry studies on the interfacial width between polystyrene and various poly(alkylmethacrylates)

1999

From neutron reflectometry we have obtained the interfacial width (typically 2-8 nm) between incompatible polymers above the glass transition temperatures. The investigated polymer bilayers consist of a deuterated polystyrene top layer and various poly(alkylmethacrylates) as a bottom layer. We obtained interesting effects of the length of the alkyl group on the interfacial width. Using mean-field theory we calculate Flory-Huggins-Stavermann interaction parameters X from the interfacial width a I data. These results are compared with investigations of the interfacial width between deuterated poly(methylmethacrylate) and respective polyalkyl-methacrylates.

Rheological characterization of polycaprolactam anionically synthesized in the presence of lithium chloride

1980

Melt viscosity and dynamic-mechanical data are reported for samples obtained by anionic polymerization of caprolactam, in the presence of LiCl. The full body of results is essentially in line with those previously reported relative to mixtures of inorganic salts and commercial nylon 6, In particular a drastic-decrease of the melting point and of the rate of crystallization is confirmed as well as an increase of the glass transition temperature and of the melt viscosity. Some quantitative differences exist, which may be attributed to the different molecular weight distribution in the polymers employed in the present work.

Strain rate effect in the single-fiber-fragmentation test

2001

The single fiber fragmentation test (SFFT) has been widely used to characterize the interface in fiber-reinforced polymers. The purpose of the work reported here was to determine the effect of strain rate on the fiber fragment lengths obtained in the SFFT. Three materials systems were used to make single-fiber-composite specimens: E-glass fiber/polycarbonate matrix, AS4-carbon fiber/polycarbonate matrix, and AU4-carbon fiber/polycarbonate matrix. The fiber-matrix adhesion in all three systems is based on physisorption rather than chemisorption. Each system was tested at strain rates ranging over four orders of magnitude. Results are reported in terms of fragment length, the dependent variab…