Search results for "Glass"
showing 10 items of 1153 documents
Diffusion of spherical micronetworks in polymer diluent systems and melts studied by dynamic light scattering techniques
1994
Spherical polystyrene (PS) micronetworks can be prepared in microemulsion with bulk radii of 5–60 nm and different cross-linking densities. The diffusion of these PS spheres has been studied in polymer diluent systems ranging from dilute solutions to plasticized melts by using forced Rayleigh scattering and photon correlation spectroscopy. On increasing the PS concentration, a colloid glass transition is observed at a volume fraction ΦC ≈ 0.64 of the swollen spheres. At higher concentration inside the “colloid glass” state the sphere diffusion is slowed down and becomes very complex but can be observed up to the limit of a melt of collapsed spheres.
Effect of cooling rate on the viscoelastic properties in the plastic zone of solid polymers
1979
PMMA and PC samples were subjected to several cooling rates from the glass transition temperature.
Dependence of Coefficient of volumetric thermal expansion (CVTE) of glass fiber reinforced (GFR) polymers on the glass fiber content
2007
In a Glass Fiber Reinforced (GFR) polymer, the coefficient of volumetric thermal expansion CVTE (determined as a sum of the coefficients of linear thermal expansion CLTE’s for the three principal directions) is sometimes much smaller than the value predictable on the basis of well acquainted models, such as Chow model, taking into account fibers anisotropy and aspect ratio.
Indentation test as a tool for monitoring the solidification process during injection molding
2003
An inline method for monitoring the solidification process during the injection molding of semicrystalline polymers is demonstrated. The method has been applied to various poly(ethylene terephthalate) (PET) and poly(buthylene terephthalate) (PBT) samples. The technique is based on a simple device by which an additional ejector pin is pushed onto the injection-molded part with a fixed force at different times during the solidification phase while the mold remains closed. The residual deformation (the so-called indentation depth) due to the applied load is measured offline after ejection. By the performance of indentation at different times during the cooling phase, an indentation depth profi…
Extension of the Concept of Intrinsic Viscosities to Arbitrary Polymer Concentration: From [η] via {η} to Intrinsic Bulkiness
2019
The capabilities of an alternative definition of intrinsic viscosities [η] published some years ago is being studied by means of comprehensive viscometric data reported in the early days of polymer science. It introduces the generalized intrinsic viscosity {η} as the specific hydrodynamic volume at arbitrary polymer concentration c. {η} quantifies the size of the flow unit and decreases monotonously for T ≫ Tg (glass transition temperature) as a function of c but passes a pronounced minimum as T approaches Tg. In the limit of the pure polymer melt, {η} becomes ; this newly introduced property is termed intrinsic bulkiness, by analogy to the intrinsic viscosity, and provides noncalorimetric …
The glass transition behaviour of salted nylon 6
1981
Glass transition measurements of nylon-6/lithium halides mixtures have been carried out in wide range of frequency with the aid of different experimental techniques. The results show an increase of the glass transition temperature when the salt is present and prove the larger effectiveness of lithium chloride with respect of lithium bromide. This effect, in line with the large reduction of the specific volume caused by the salt, is due to the formation of a pseudo-cross-linking between lithium ions and the carbonyl-oxygen groups of the polyamide.
Molecular Mobility in Oriented and Unoriented Membranes Based on Poly[2-(Aziridin-1-yl)ethanol]
2021
Unoriented and oriented membranes based on dendronized polymers and copolymers obtained by chemical modification of poly[2-(aziridin-1-yl) ethanol] (PAZE) with the dendron 3,4,5-tris[4-(n-dodecan-1-yloxy)benzyloxy]benzoate were considered. DSC, XRD, CP-MAS NMR and DETA, contribute to characterize the tendency to crystallize, the molecular mobility of the benzyloxy substituent, the dendritic liquid crystalline group and the clearing transition. The orientation of the mesogenic chain somewhat hindered this molecular motion, especially in the full substituted PAZE. The fragility, free volume and thermal expansion coefficients of these membranes near the glass transition are related to the orie…
The effect of macromolecular architecture of ethylene copolymers with multi-alkenylsilsesquioxane on morphological, rheological and dynamic mechanica…
2021
Abstract The influence of the degree and the way of incorporation of multi-alkenylsilsesquioxane into the polymer chain on morphological, rheological and dynamic mechanical parameters were determined. It was found that POSS incorporated into the polymer chain was located outside the crystalline structure of lamella in amorphous phase. The incorporation of POSS-6-2 as a pendant group resulted in significant increase of separation of macromolecules. The key factor in rheological and dynamic mechanical behavior of copolymers turned out to be the way of POSS incorporation into the polymer chain. The incorporation of POSS into the polymer chain as a pendant group resulted in decreased relaxation…
The glass transition in polymer melts
1994
This paper presents some results of a Monte Carlo simulation for the glass transition in two- and three-dimensional polymer melts. The melt was simulated by the bond-fluctuation model on a d-dimensional cubic lattice which was combined with a two-level hamiltonian favouring long bonds in order to generate a competition between the energetic and topological constraints in the system. This competition prevents crystallization and makes the melt freeze in an amorphous structure as soon as the internal relaxation times match the observation time of the simulation set by the cooling rate. The freezing point of the melt, i.e the glass transition temperature Tg, thus depends upon the cooling rate …
Novel Amphiphilic Styrene-Based Block Copolymers for Induced Surface Reconstruction
2008
This paper describes the synthesis of amphiphilic block copolymers by living radical polymerization (NMP) of new styrene-like monomers. The polar monomers (ethylene oxide side chains and free hydroxyl- or amino-groups after deprotection) were polymerized in a “protected form” to adjust the solubility of the monomers. In this way high molar mass polymers with a narrow polydispersity (around or below 1.2) were accessible. In the bulk state hydrophobic and hydrophilic domains demix. By exposing thin films of these polymers to vacuum (air) or alternatively to water or a hydrophilic surface it becomes possible to switch the surface polarity reversibly between contact angles of about 105° and 83°…