Search results for "Gradation"
showing 10 items of 1275 documents
Incorporation of an antibiotic in poly(lactic acid) and polypropylene by melt processing
2016
Purpose In this work an antibiotic, ciprofloxacin (CFX), was incorporated into 2 different polymeric matrices, poly(lactic acid) (PLA) and polypropylene (PP), to provide them with antimicrobial properties. The influence of CFX content on release kinetics and on antimicrobial and mechanical properties was evaluated. Methods CFX was incorporated into both the polymers by melt mixing. Results The effect of CFX incorporation was found to strongly depend on which polymer matrix was used. In particular, the antimicrobial tests revealed that PLA samples containing CFX produced no inhibition zone and only a slight antibacterial activity was observed when the highest concentration of CFX was added t…
Hybrid paper–TiO2 coupled with a Cu2O heterojunction: an efficient photocatalyst under sun-light irradiation
2016
Hybrid paper-TiO2, paper-Cu2O-TiO2 and paper-TiO2-Cu2O photocatalysts were prepared via a non-hydrolytic sol-gel process followed by mild hydrothermal treatment to generate the TiO2 layer, and a reduction process to form the Cu2O nanoparticles. The hybrid photocatalysts have been characterized by Raman, TGA, FE-SEM, UV-Vis and XPS. The immobilized TiO2 was found to form a homogeneous thin layer composed of nanoparticles with a size smaller than 10 nm. The Cu2O nanoparticles with sizes of 30-100 nm were generated either on the top of the TiO2 layer or by reduction of Cu2+ ions. All the prepared hybrid catalysts showed efficient photocatalytic properties for the degradation of toluidine when …
X-ray micro-computed tomography investigation of fibre length degradation during the processing steps of short-fibre composites
2014
The mechanical properties of composites in the fibre direction are mainly attributed to the fibre slenderness, or aspect ratio. A trade-off between performance and processability is usually required, and dependent on the intended application. If the fibre length could be retained or not severely degraded during various processing steps towards the injection-moulded component, a stiffer and stronger composite product could be obtained. The processing steps for injection moulded wood-fibre composites here include: Pulping, commingling, extrusion, pelletizing, and injection moulding. To tune the processing parameters systematically for retained fibre length, it would be useful to investigate t…
Atmospheric Turbulence Effects Removal on Infrared Sequences Degraded by Local Isoplanatism
2007
When observing an object horizontally at a long distance, degradations due to atmospheric turbulence often occur. Different methods have already been tested to get rid of this kind of degradation, especially on infrared sequences. It has been shown that the Wiener filter applied locally on each frame of a sequence allows to obtain good results in terms of edges, while the regularization by the Laplacian operator applied in the same way provides good results in terms of noise removal in uniform areas. In this article, we present hybrid methods which take advantages of both Wiener filter and Laplacian regularization.
Effect of relative humidity on carvacrol release and permeation properties of chitosan based films and coating
2014
International audience; The influence of water vapour conditions on mass transport and barrier properties of chitosan based films and coatings were studied in relation to surface and structural properties. Water contact angles, material swelling, polymer degradation temperature, barrier properties (PO2, PCO2, WVP) and aroma diffusion coefficients were determined. The solvent nature and the presence of carvacrol influenced the surface and structural properties and then the barrier performance of activated chitosan films. Increasing RH from 0% to 100% led to a significant increase in material swelling. The plasticization effect of water was more pronounced at high humid environment, while at …
Performance assessment of field deployed multi-crystalline PV modules in Nordic conditions
2019
This paper presents an investigation of data monitoring quality and evaluation of performance degradation of four different multi-crystalline silicon (mc-Si) photovoltaic (PV) modules installed in the higher latitude conditions in southern Norway. Degradation of each module has been investigated in terms of degradation of short-circuit current (I SC ), open-circuit voltage (V OC ), fill factor (FF) and maximum power (P MPP ). The analysis for the period of monitoring data from 2014 to 2018 show no considerable module degradation compared to the standard degradation rate of all parameters. The statistical analysis of I SC shows an average degradation of 0.17% for all modules. Spectral correc…
Impact of hydrothermal ageing on the thermal stability, morphology and viscoelastic performance of PLA/sisal biocomposites
2016
The influence of the combined exposure to water and temperature on the behaviour of polylactide/sisal biocomposites coupled with maleic acid anhydride was assessed through accelerated hydrothermal ageing. The biocomposites were immersed in water at temperatures from 65 to 85 °C, between the glass transition and cold crystallisation of the PLA matrix. The results showed that the most influent factor for water absorption was the percentage of fibres, followed by the presence of coupling agent, whereas the effect of the temperature was not significant. Deep assessment was devoted to biocomposites subjected to hydrothermal ageing at 85 °C, since it represents the extreme degrading condition. Th…
Ecosystem responses to land abandonment in Western Mediterranean Mountains
2017
Agricultural expansion in the Mediterranean resulted in plant and soil degradation due to the intensive use, climate conditions, and rugged terrain. After abandonment, the recovery of vegetation contributed to improvement in soil quality from a hydrological, pedological and geomorphological point of view. This paper shows three examples of ecosystem evolution in abandoned fields in Valencia, Murcia and Andalucia and the application of different methodological approaches that resulted in similar findings. In Valencia, the main responses were the recovery of vegetation after land abandonment and an increase in organic matter and infiltration capacity of soils. In Murcia, with the exception of…
Urban growth (1956-2012) and soil sealing in the metropolitan area of Valencia (Eastern Spain)
2019
[EN] The aim of this study is to understand the urban growth dynamics from the mid-1950s to 2012 in the Metropolitan Area of Valencia, eastern Spain, and its impact on soils. The study area is a very interesting example of the many changes in land use and land cover in the landscape of Mediterranean alluvial plains. The analysis of urban growth was based on photo interpretation of aerial photographs and GIS based methodology. At a detailed scale (1:10,000), results show that there has been a highly dynamic process produced by the extent of land developed as urban area. In 1956 only 3,441 hectares (9.3% of the overall study area) were occupied by urban use. In 2012 the total sealed surface w…
The influence of fire history, plant species and post-fire management on soil water repellency in a Mediterranean catchment : The Mount Carmel range,…
2017
Fire is a key factor impacting soil hydrology in many Mediterranean catchments. Soil water repellency (SWR) can stimulate land degradation processes by reducing the affinity of soil and water thereby triggering a reduction in soil fertility and increasing soil and water losses. The effects of two consequent fires (1989 and 2005) on SWR were assessed in the Carmel Mountains, Israel. Fire history, plant recovery and post-fire management (14 treatments) were investigated as determining factors in a time dependent system. In total 210 locations were investigated 9 times from October 2011 to February 2012, which totals 1890 water drop penetration tests that were performed. During each visit to t…