Search results for "HARDNESS"

Effects of fluoride versus amorphous calcium phosphate solutions on enamel microhardness of white spot lesions: An in-vitro study

2019

Background Development of white spot lesions around orthodontic fixed orthodontic appliances is a common finding, especially in patients with poor oral hygiene. One of the conservative interventions for regression of these lesions is using chemical solutions. The current study aimed to compare the effectiveness of fluoride and amorphous calcium phosphate (ACP) on microhardness improvement of affected enamel. Material and Methods Forty-five intact human incisor teeth were selected and randomly divided into 3 groups of 15. Fluoride group, ACP group and artificial saliva group (control group). Inducing of white spot lesion was done by PH-cycling model. Samples of the first and second group wer…

Comparative evaluation of Nano-Hydroxyapatite preparation and Calcium Sucrose Phosphate on microhardness of deciduous teeth after iron drop exposure …

2016

Background To evaluate and compare the microhardness of deciduous teeth treated with nano-hydroxyapatite and calcium sucrose phosphate after iron drop exposure. Material and Methods Twenty healthy anterior deciduous teeth were collected and stored in 0.9% saline solution at room temperature. All the teeth were immersed in artificial saliva in an incubator shaker at 37° for an hour and then subjected to Vickers microhardness test at 100g load for 5 seconds. The teeth were then immersed in iron drop for 5 minutes, twice daily, rinsed with distilled water and kept in artificial saliva. This procedure was repeated for 7 days and teeth were subjected to microhardness testing. Further, the teeth …

Laser-Casein phosphopeptide effect on remineralization of early enamel lesions in primary teeth

2014

Background: The aim of this study was to assess the effect of Nd:YAG laser irradiation following casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) application on calcium and phosphate concentration and surface microhardness (SMH) of enamel surface in artificial white spot lesions of primary teeth. Material and Methods: Eighty teeth with artificial white spot lesions were randomly divided into four groups: (A) distilled and deionized water, (B) Nd:YAG laser, (C) CPP-ACP crème, & (D) CPP-ACP plus laser. SMH was measured using Vickers diamond indenter in Vickers Hardness Number (VHN). Two samples of each group were analyzed using scanning electron microscope (SEM). The results were a…

FACTORS AFFECTING THE INFESTATION DUE TO BACTROCERA OLEAE (ROSSI) IN SEVERAL SICILIAN OLIVE CULTIVARS

2010

The effects of intensity, frequency, static load, and shore hardness on different parameters in vibration sensitivity measurements.

1987

The effects of shore hardness, static load, frequency, and intensity of vibration on the amplitude and dynamic force effects of vibration were studied in conditions corresponding to those occurring in vibrotactile sensitivity measurements. The measurements were performed on three silicon plates of known shore hardness. The results indicated that the effect of differences in elasticity on the vibration amplitudes was evident at lower frequencies up to about 200 Hz whereas at higher frequencies the amplitudes remained at the same level, regardless of elasticity. On dynamic force the effect of elasticity was observed at all frequencies studied (50-500 Hz). The static load of the contractor had…

Eroded enamel rehardening using two intraoral appliances designs in different times of salivary exposure.

2019

Background The aim of this study was evaluated the eroded enamel rehardening potential using upper palatal and lower buccal removable appliances in different times of salivary exposure (30 min, 1h, 2h, 12h) after a single erosive challenge event. Material and Methods After initial surface hardness evaluation, bovine enamel blocks were eroded in vitro (0.01 M hydrochloric acid, pH 2.3, 30 seconds), selected (n = 160) and randomly assigned to the two appliance designs and twenty volunteers. Four enamel blocks were inserted in each removable appliance. On the in situ phase, the volunteers were instructed to use the upper palatal and lower buccal appliances simultaneously for 12 nonconsecutive …

Radiation Hardness Assurance Through System-Level Testing: Risk Acceptance, Facility Requirements, Test Methodology, and Data Exploitation

2021

International audience; Functional verification schemes at a level different from component-level testing are emerging as a cost-effective tool for those space systems for which the risk associated with a lower level of assurance can be accepted. Despite the promising potential, system-level radiation testing can be applied to the functional verification of systems under restricted intrinsic boundaries. Most of them are related to the use of hadrons as opposed to heavy ions. Hadrons are preferred for the irradiation of any bulky system, in general, because of their deeper penetration capabilities. General guidelines about the test preparation and procedure for a high-level radiation test ar…

Surface Development of (As2S3)1–x (AgI)x Thin Films for Gas Sensor Applications

2011

Thin (As2S3)100−x(AgI)x (x = 0–40) films were deposited by thermal vacuum evaporation from the respective bulk glasses; their structure and morphology before and after illumination with light have been studied by scanning electron microscopy (SEM). As-deposited films show fractional evaporation and surface inhomogeneities but after illumination they become uniform on the surface and in the depth as revealed by SEM top-view and cross-section images. Mechanical parameters like stress and microhardness of as-prepared and illuminated films were also investigated. The results from the stress measurements show variation in both the sign and the magnitude of the values with increasing AgI content …

Effects of Different Percentages of Microhydroxyapatite on Microhardness of Resin-modified Glass-ionomer and Zirconomer

2016

Background Hydroxyapatite (HA) is the main mineral component of the tooth structure, which exhibits considerable biological behavior and its incorporation might improve microhardness of dental materials. Microhardness of restorative materials, like glass-ionomer, is critical for the clinical longevity of restorations. The aim of this study was to evaluate the microhardness of two glass-ionomers types by incorporating different percentages of microhydroxyapatite. Material and Methods In this study, 80 disc-shaped experimental specimens (6 mm in diameter, 2 mm in height) were prepared in 8 groups, including resin-modified glass-ionomer (RMGI, GC, Gold Label, Japan), zirconia-reinforced glass-…

Minimal exposure time of different LED-curing devices

2007

Abstract Objectives The purpose of the study was to investigate the shortest possible exposure time of different LED-curing devices for five different resin composites in a clinically relevant in vitro-model, where a 7 mm distance from the light guide tip to the bottom side of the cavity was compiled. Methods Resin composite samples (Tetric EvoCeram A3, Filtek Supreme XT A3B, Premise A3, CeramX Mono M5, QuiXfil) were filled in three increments of 2 mm thickness each in stainless steel moulds (O = 5 mm, h  = 6 mm, n  = 9). The samples were incrementally exposed to different blue LED-curing devices (Bluephase, Bluephase C8, Bluephase 16i/Ivoclar Vivadent, L.E.Demetron II/sds Kerr, Elipar Free…