Search results for "HYDRAULICS"

On the hydraulic behaviour of ITER Shield Blocks #14 and #08. Computational analysis and comparison with experimental tests

2016

Abstract As a consequence of its position and functions, the ITER blanket system will be subjected to significant heat loads under nominal reference conditions. Therefore, the design of its cooling system is particularly demanding. Coolant water is distributed individually to the 440 blanket modules (BMs) through manifold piping, which makes it a highly parallelized system. The mass flow rate distribution is finely tuned to meet all operation constraints: adequate margin to burn out in the plasma facing components, even distribution of water flow among the so-called plasma-facing “fingers” of the Blanket First Wall panels, high enough water flow rate to avoid excessive water temperature in …

Steady state and transient thermal–hydraulic analyses on ITER divertor module

2005

Abstract One of the most challenging components of ITER is the divertor devoted at controlling the characteristics of the plasma boundary, exhausting the α particles and reducing the impurities in the plasma. The thermal–hydraulic design of the divertor is particularly, demanding because of the high heat loads and the cooling flow margin in the plasma-facing components (PFCs). The pressure drop is limited by the pumping power and also avoiding the risk of reaching critical heat flux (CHF). Furthermore, for maintenance operation foreseen, each single divertor cassette should be drained and dried before withdrawing it out from the vacuum vessel. To address these requirements, European Fusion …

Evaluating the Effects of the Rill Longitudinal Profile on Flow Resistance Law

2022

In this paper, for the first time, the effect of the longitudinal profile shape of the rill (uniform, concave, and convex) on flow resistance law was studied. The first part of the paper is based on a theoretical equation to estimate the Darcy–Weisbach friction factor f, deduced from the power velocity distribution and rill measurements performed on a plot. At first, the equation to estimate the Γ parameter of the velocity profile was calibrated using all available measurements. Then an analysis of the hydraulic characteristics at reach scale, for comparable values of discharge, was carried out, comparing the different profile shapes. To assess the influence of the rill profile …

Hydraulic kinetics of the graft union in different Olea europaea L. scion/rootstock combinations

2007

The hydraulic resistance of young olive trees grafted on rootstocks with contrasting size-controlling potential was measured 30, 90, 360 and 480 days after grafting. Olive (Olea europaea L.) clones inducing plant vigorous growth (Leccino ‘Minerva’, LM) or dwarfing (Leccino ‘Dwarf’, LD) were studied in different scion/rootstock combinations (LD/LD, LD/LM, LM/LD, LM/LM). Plants growing on LD root systems developed lower leaf surface areas (about 50% less) than plants grafted on LM rootstocks. Graft union represented the largest fraction (up to 85%) of whole-plant hydraulic resistance 30 days after grafting, and still represented an important fraction of it 2 months later (40–55%). Four-hundre…

Kairomone involvement in the host specificity of the egg parasitoid Trissolcus basalis

2006

This paper reports the results of a comparative laboratory analysis of the behavioural responses of the egg parasitoid Trissolcus basalis (Wollaston) (Hymenoptera: Scelionidae) to semiochemical cues from four species of pentatomid bugs, Nezara viridula (L.), Eurydema ventrale Klt., Murgantia histrionica Hahn. and Graphosoma semipunctatum F. (Heteroptera: Pentatomidae). In a Y-tube olfactometer, T. basalis was attracted by volatile chemicals from N. viridula, but not from other pentatomid species. In an open arena, the parasitoid reacted to chemical trails left on filter paper by all the species but most intensely to those left by N. viridula. However, upon encountering pentatomid eggs, T. b…

The hydraulic behaviour of the prototype of on a ITER divertor cassette

2009

Digital Hydraulic Technology for Linear Actuation:A State of the Art Review

2020

This paper analyses the current state of the art in linear actuation with digital hydraulics. Based on the differences in their aims the paper partitions the area into four actuation concepts – parallel valve solutions, single switching valve solutions, multi-chamber cylinders, and multi-pressure cylinders. The concepts are evaluated based on accuracy and smoothness of motion, switching load, reliability, efficiency and the number of components required.

CFD Assisted Steady-State Modelling of Restrictive Counterbalance Valves

2020

The counterbalance valve is an important component in many hydraulic applications and its behaviour hugely impacts system stability and performance. Despite that, CBVs are rarely modelled accurately due to the effort required to obtain basic model parameters and the complexity involved in identifying expressions for flow forces and friction. This paper presents a CFD assisted approach to steady-state modelling of CBVs. It is applied to a 3-port restrictive commercially available counterbalance valve. The model obtained is based on detailed measurements of the valve geometry, a single data set and CFD modelling and includes flow forces and friction. The CFD assisted model is compared to expe…

Analysis of the SPES-3 direct vessel injection line break by using TRACE code

2011

Preliminary thermal-hydraulic analysis of the EU-DEMO Helium-Cooled Pebble Bed fusion reactor by using the RELAP5-3D system code

2021

Abstract In the frame of the activities promoted and encouraged by the EUROfusion Consortium aimed at developing the EU-DEMO fusion reactor, great emphasis has been placed at a very early stage of the design to incorporate the provisions needed to improve the overall plant safety and reliability performances as well as to analyse possible mitigation actions. In this framework, the research activity has been focused on the representative and safety relevant cooling loop of the Helium Cooled Pebble Bed (HCPB) Breeding Blanket (BB) Primary Heat Transfer System (PHTS), purposely selected by the safety team, in order to assess its thermal-hydraulic behaviour during normal operational conditions …