Search results for "Hardness"

Influence of energy drinks on enamel erosion : in vitro study using different assessment techniques

2021

Background Dental erosion has become a relevant public health problem in recent years and is related to the increase in the consumption of acidic beverages. Objective: The aim of the present study was to evaluate the erosive potential of energy drinks on dental enamel using an in vitro erosion model. Material and Methods Thirty-eight blocks of human enamel were divided into four groups: G1- TNT Energy Drink®(n=8), G2- Red Bull® (n=10), G3- Monster Energy® (n=10), and G4- Coca-Cola® (n=10) (positive control). For the chemical analysis, the pH values, titratable acidity, and buffering capacity of the beverages were measured in triplicate. For the erosive test, the specimens were immersed in t…

The effect of protocol for disinfection of extracted teeth recommended by center for disease control (CDC) on microhardness of enamel and dentin

2015

Background: According to the guideline of the United States center for disease control (CDC), the extracted teeth should be sterilized by autoclaving or storage in 10% formalin before using for educational or research purposes. The objective of this study was to evaluate the effect of this protocol on microhardness of dentin and enamel. Material and Methods: Thirty extracted single-root teeth were used in this study. The crowns were resected, and the roots were longitudinally sectioned into two halves. The Vickers microhardness (VHN) of specimens was measured on polished canal dentin and buccal enamel surfaces. The crowns were randomly divided into three groups (n=10). Group 1 and 2 were st…

COMPUTED TOMOGRAPHY TO PREDICT HARDNESS OF BILEDUCT STONES BEFORE ENDOSCOPIC LITHOTRIPSY

1984

Micro and macro mechanical characterization of friction stir welded Ti–6Al–4V lap joints through experiments and numerical simulation

2013

Abstract Lap joints of Ti–6Al–4V were produced and the effect of the main process parameters was studied through macro and micro investigations highlighting mechanical resistance, microhardness profiles, grain size and phase distributions. A dedicated numerical model was used to link the input process parameters to temperature and strain distributions and to the final microstructure in the welded joint. It is found that the strain produced in the stir zone by proper combination of process parameters plays a fundamental role in the final microstructure and mechanical properties of the joints.

Experimental and Numerical Analysis of Microstructure Evolution during Linear Friction Welding of Ti6Al4V

2015

Abstract Linear Friction Welding (LFW) is a solid state welding process used to joint bulk components. In the paper, an experimental and numerical study on LFW of Ti6Al4V titanium alloy is presented. A laboratory designed LFW machine has been used to weld the specimens with different contact pressure and oscillation frequency. The joint microstructure has been experimentally observed with SEM and EDS. A dedicated numerical model, able to predict temperature, strain and strain rate distribution as well as the phase volume fraction evolution, has been utilized to predict the final microstructure in the welded parts. It was found that complete transformation of the alpha phase into beta phase …

Enhanced thermoelectric performance in the p-type half-Heusler (Ti/Zr/Hf)CoSb0.8Sn0.2 system via phase separation

2014

A novel approach for optimization of the thermoelectric properties of p-type Heusler compounds with a C1b structure was investigated. A successful recipe for achieving intrinsic phase separation in the n-type material based on the TiNiSn system is isoelectronic partial substitution of Ti with its heavier homologues Zr and Hf. We applied this concept to the p-type system MCoSb0.8Sn0.2 by a systematic investigation of samples with different compositions at the Ti position (M = Ti, Zr, Hf, Ti0.5Zr0.5, Zr0.5Hf0.5, and Ti0.5Hf0.5). We thus achieved an approximately 40% reduction of the thermal conductivity and a maximum figure of merit ZT of 0.9 at 700 °C. This is a 80% improvement in peak ZT fr…

Friction Stir Processing: thermo-mechanical loads and consequent effects on the local material characteristics

2008

The present article is focused on the correlation between the applied thermal and mechanical loads and the consequent effects on the material in friction stir processing (FSP) operations. On one hand, the actions exerted in FSP are split compared to the results obtained with a tool without the pin at its end to a traditional one with a cylindrical pin. In this way, the thermal flux determined by the frictional forces at the tool—shoulder—workpiece interface is secluded from the mechanical stirring action made by the tool pin. On the other hand, the processed specimens are analysed in terms of residual stress state, microhardness, and average grain size values. An in-process heat treatment …

Characterization of Fusion Lines Obtained with Laser Welding on Ductile Iron Plates

2016

This paper studies the ductile iron (DI) weldability using laser welding. For performing an Yb:YAG continuous laser was used, with a maximum power of 6 kW. The parametrical window power (P) - welding speed (S) was explored by carrying out the fusion lines on ductile iron plates without preheating, to determinate areas of weldability (complete penetration, correct geometry) to allow further characterization. The criteria for selection of focus areas were the geometry of the fusion lines and the absence of the welding defects. The unsatisfactory domains were characterized by: collapse of the melted metal, incomplete penetration, low fusion lines quality (geometry, compactness). In present stu…

Spatial identification of the overionized plasma in W49B

2010

Recent Suzaku X-ray observations of the ejecta-dominated supernova remnant W49B have shown that in the global spectrum there is a clear indication for the presence of overionized plasma whose physical origin is still under debate. In order to ascertain the physical origin of such a rapidly cooling plasma, we focus on the study of its spatial localization within the X-ray emitting ejecta. We confirm the presence of a saw-edged excess (interpreted as a strong radiative recombination continuum) in the global spectrum above 8 keV, emerging above the ionization-equilibrium model. We produce a hardness ratio map to determine where the plasma is overionized and we perform a spectral analysis of th…

Obtaining of nanostructured ZnO coatings using mechanoactivated oxidation

2007

The concept to use nanostructured state of metal at the instant of destruction in air environment was used to obtain nanostructured Zn-ZnO coatings on glass and quartz by mechanical method. Subsequent annealing in the ambient atmosphere, annealing in vacuum and irradiation with 532-nm YAG:Nd laser were used to obtain completely oxidized, transparent ZnO coatings. The saturated with oxygen nanostructured coatings were transformed into nanostructured ZnO coatings after annealing above 773K or irradiation with laser (allowing to reach 673K) in ambient atmosphere. AFM and SEM images show that after annealing ZnO coatings have multi-shaped structure. The formation of ZnO need-like whiskers (d = …