Search results for "Heat Exchanger"
showing 10 items of 71 documents
Novel Wireless Sensor System for Dynamic Characterization of Borehole Heat Exchangers
2011
The design and field test of a novel sensor system based in autonomous wireless sensors to measure the temperature of the heat transfer fluid along a borehole heat exchanger (BHE) is presented. The system, by means of two specials valves, inserts and extracts miniaturized wireless sensors inside the pipes of the borehole, which are carried by the thermal fluid. Each sensor is embedded in a small sphere of just 25 mm diameter and 8 gr weight, containing a transceiver, a microcontroller, a temperature sensor and a power supply. A wireless data processing unit transmits to the sensors the acquisition configuration before the measurements, and also downloads the temperature data measured by the…
Numerical evaluation on performances of AHU equipped with a cross flow heat exchanger in wet and dry operation
2012
Abstract In this paper the comparison between the performance of a cross flow heat exchanger in wet and dry operation for air handling process has been investigated. In addition, a case study of application of the component to perform indirect evaporative cooling in a AHU was studied with the software TRNSYS.Using experimental data and an appropriate analytical method, energy saving performances of the system has been evaluated through the entire cooling season for a typical Mediterranean site. Results show that high energy saving potential can be obtained if the component is operated in wet operation in term of reduction of electricity consumption.
Analysis of a full-scale integral test in PERSEO facility by using TRACE code
2017
Over the last decades a lot of experimental researches have been done to increase the reliability of passive decay heat removal systems implementing in-pool immersed heat exchanger. In this framework, a domestic research program on innovative safety systems was carried out leading the design and the development of the PERSEO facility at the SIET laboratories. The configuration of the system consists of an heat exchanger contained in a small pool which is connected both at the bottom and at the top to a large water reservoir pool. Within the frame of a national research program funded by the Italian minister of economic development, the DEIM department of the University of Palermo in coopera…
Thermoelectric Heat Exchange and Growth Regulation in a Continuous Yeast Culture
2018
We have designed a thermoelectric heat exchanger (TEHE) for microbial fermentations that is able to produce electric power from a microbial continuous culture using the intrinsic heat generated by microbial growth. While the TEHE was connected, the system proved able to stably self-maintain both the temperature and the optical density of the culture. This paves the way toward a more sustainable operation of microbial fermentations, in which energy could be saved by converting part of the metabolic heat into usable electric power.
Conjugate heat transfer analysis within in lattice-filled heat exchanger for additive manufacturing
2020
Compact heat exchangers for heat removal has become one of the most effective cooling techniques. In this paper, numerical scheme to simulate conjugated heat transfer using additively manufactured ...
Effect of Heat Exchange Transient Conditions with Moving Water-Air Interface on Space Charge Accumulation in Undersea HVdc Cables
2021
The accumulation of space charge inside the dielectric layer of an HVdc cable is one of the most important issue to be considered in the design stage and during the operating conditions. The separation of space charge is due to several factors including the dependence on temperature of the electrical conductivity of the insulation and the establishment of a thermal gradient under load conditions. This article is focused on the investigation of the effect of an axial heat transmission on the space charge and electric field distributions in an HVdc cable. In order to assess the impact of this phenomenon, a case study involving a cable immersed partly in water and partly in air has been simula…
Temperature measurements along a vertical borehole heat exchanger: A method comparison
2019
Abstract The standard thermal response tests (TRT) provide integral and effective thermal parameters of the ground in the vicinity of borehole heat exchangers (BHE). However, typical ground properties are heterogeneously distributed. As a result, advanced TRT such as distributed and enhanced TRT are growing in popularity as they provide more spatial information of the thermal properties. Thus, the objective of this study is to compare various instruments to measure the depth-dependent temperatures using standard Pt100-sensors, fiber optical thermometers and novel instruments such as Geowire, Geoball and GEOsniff®. The investigations are carried out in a 30 m length test borehole. The result…
Sample building orientation effect on porosity and mechanical properties in Selective Laser Melting of Ti6Al4V titanium alloy
2022
Abstract In recent decades, the focus of research has shifted towards new production technologies with the aim of optimizing production and reducing costs. These innovative technologies include additive manufacturing processes as Selective Laser Melting (SLM). The analysis of the literature on the identification of optimal building orientation to maximize the mechanical properties and minimize porosity of the final products highlights contrasting results, denoting that the thermomechanical complexity of the process, as associated with the variation of the building orientation, has not been fully clarified. A study in which the building orientation effect was evaluated together with the geom…
An interactive multi-objective approach to heat exchanger network synthesis
2010
In this work we present a multi-objective approach to heat exchanger network synthesis. The approach solves a modified version of the Synheat model using an interactive multi-objective optimisation method, NIMBUS, which is implemented in GAMS. The results obtained demonstrate the potential of interactive multi-objective optimisation.
Ground Coupled Heat Pumps in Mixed Climate Areas: Design, Characterization and Optimization
2010
This contribution reviews the research work developed by the authors on the design, characterization and optimization of ground coupled heat pumps in mixed climates areas. The design of a ground coupled heat pump HVAC system starts with the estimation of the thermal loads that the air-conditioned area demands. The capacity of the ground source airconditioning system is determined from this thermal load estimation. With this value and a proper estimation of the ground thermal properties, the characteristics of the water to water heat pump and the required length and layout of the borehole heat exchangers are estimated. Determining ground thermal properties is crucial for an accurate design o…