Search results for "Heat Transfer"
showing 10 items of 442 documents
Effect of a Steady Magnetic Field and Imposed Rotation of Vessel on Heat and Mass Transfer in Swirling Recirculating Flows
1999
A simplified theoretical model for the solidification interface shape prediction is introduced and tested. We linearised a coupled hydrodynamic-solidification problem about the state with a flat interface. In such a way we split the problem into a hydrodynamic part with a flat solid-liquid front and a solidification part with a calculated heat flux from the liquid phase. The method allows obvious conclusions on optimum heat conditions near the solidification interface providing its flatness and maximum pulling velocity at the same time. Comparison to the results by FLUENT package showed that the method provides a reasonable accuracy even for a noticeably deformed interface shape. Another pa…
Assessment of DEMO WCLL breeding blanket primary heat transfer system isolation valve absorbed doses due to activated water
2020
Abstract Within the framework of the activities foreseen by the EUROfusion action on the cooling water activation assessment for a DEMO reactor equipped with a Water Cooled Lithium Lead Breeding Blanket (WCLL BB), the University of Palermo is involved in the investigation of the absorbed dose induced by the decay of nitrogen radioisotopes produced by water activation, in the main components (e.g. isolation valves) of both First Wall (FW) and Breeder Zone (BZ) cooling circuits. The aim of this work is to assess the spatial distribution of the absorbed dose in the DEMO Upper Pipe Chase (UPC), focusing the attention on the space neighbouring a typical isolation valve of the Primary Heat Transf…
A computational procedure for the investigation of whipping effect on ITER High Energy Piping and its application to the ITER divertor primary heat t…
2015
Abstract The Tokamak Cooling Water System of nuclear facility has the function to remove heat from plasma facing components maintaining coolant temperatures, pressures and flow rates as required and, depending on thermal-hydraulic requirements, its systems are defined as High Energy Piping (HEP) because they contain fluids, such as water or steam, at a pressure greater than or equal to 2.0 MPa and/or at a temperature greater than or equal to 100 °C, or even gas at pressure above the atmospheric one. The French standards contemplate the need to consider the whipping effect on HEP design. This effect happens when, after a double ended guillotine break, the reaction force could create a displa…
Large-Eddy Simulation of Flow and Heat Transfer in Compact Heat Exchangers
1994
LES results are presented for different heat exchanger geometries. Subgrid terms were usually computed by the Smagorinsky model; preliminary comparative results are also given for the ‘dynamic’ subgrid model. The numerical methods used were those implemented in a commercial general-purpose code (CFDS-FLOW3D); they included a finite-volume approach, colocated body-fitted grids, central differencing for the advection terms, the SIMPLEC algorithm, and Crank-Nicolson time stepping. Predictions arc compared with experimental measurements (including local Nu distributions), and with results from a low-Reynolds number k-e model. In most cases, LES was more ‘robust’ and required little more CPU tim…
Determination of the oxygen transmissibility and permeability of hydrogel contact lenses
1999
To test the validity of the method of stacked hydrogel contact lenses to obtain the oxygen permeability and transmissibility coefficients of the lenses, the coefficients of one low hydration (38% water) and two high hydration (55 and 58% water) hydrogel contact lenses stacked one to five on an oxygen electrode were deter- mined. From the oxygen diffusion through the lenses, the current intensity in the stationary state was determined, and from this the "instrument" the oxygen transmis- sibility was obtained. The permeability coefficients of the lenses, corrected for edge effects, were obtained from the slope of the plot of the reciprocal of the transmissibility coefficients versus the lens …
Numerical simulation of nanofluids for improved cooling efficiency in a 3D copper microchannel heat sink (MCHS)
2017
ABSTRACTIn this paper, laminar nanofluid flow in 3D copper microchannel heat sink (MCHS) with rectangular cross section, and a constant heat flux, has been treated numerically using the computational fluid dynamics software (FLUENT). Results for the temperature and velocity distributions in the investigated MCHS are presented. In addition, experimental and numerical values are compared in terms of friction factors, convective heat transfer coefficients, wall temperature and pressure drops, for various particle volume concentrations and Reynolds numbers. The numerical results show that enhancing the heat flux has a very weak effect on the heat transfer coefficient for pure water, but an appr…
An enhanced, near-term HCPB design as driver blanket for the EU DEMO
2019
The Helium Cooled Pebble Bed (HCPB) breeding blanket is a candidate as driver blanket for the EU DEMO. The reference design of the HCPB is based on a cooling plate “sandwich” arrangement built in Multi-Module Segments. This architecture significantly improved the tritium breeding performance (TBR = 1.15) and the plant circulating power (≈130 MW) compared to the former ITER-like “beer-box”-like design (TBR<1.10, plant circulating power>200 MW). However, several issues remain with this design, in which (1) the still large power required per He circulator (beyond the state-of-the-art for these components) and (2) the large tritium inventory foreseen in Be have been identified as the most…
Flow and Heat Transfer in Corrugated Passages: Direct and Large Eddy Simulation and Comparison with Experimental Results
1993
Direct and large-eddy numerical simulations are presented for the transitional and turbulent flow with heat transfer in corrugated passages, representative of compact heat exchangers such as rotary air preheaters (regenerators), at Reynolds number ranging from 103 to 104. Pressure drop and heat transfer results are compared with wind-tunnel experimental data; the agreement is quite satisfactory, and superior to that obtained by more traditional methods.
On the influence of curvature and torsion on turbulence in helically coiled pipes
2014
Turbulent flow and heat transfer in helically coiled pipes at Ret=400 was investigated by DNS using finite volume grids with up to 2.36×10^7 nodes. Two curvatures (0.1 and 0.3) and two torsions (0 and 0.3) were considered. The flow was fully developed hydrodynamically and thermally. The central discretization scheme was adopted for diffusion and advection terms, and the second order backward Euler scheme for time advancement. The grid spacing in wall units was ~3 radially, 7.5 circumferentially and 20 axially. The time step was equal to one viscous wall unit and simulations were typically protracted for 8000 time steps, the last 4000 of which were used to compute statistics. The results sho…
Fully developed laminar flow and heat transfer in serpentine pipes
2015
Abstract A serpentine pipe is a sequence of parallel straight pipe segments connected by U-bends. Its geometry is fully characterized by pipe radius, a , bend curvature radius, c and length of the straight segments, l . The repeated curvature inversion forces the recirculation (secondary flow) pattern to switch between two specular configurations, which may enhance mixing and heat or mass transfer with respect to a constant-curvature pipe at the cost of an increase in pressure drop. In the present work, fully developed laminar flow and heat transfer in serpentine pipes were investigated by numerical simulation. The curvature δ = a / c was made to vary between 0.1 and 0.5 while the paramet…