Search results for "IMPIANTI"
showing 10 items of 797 documents
A Multi-Objective Approach to Optimize a Periodic Maintenance Policy
2012
The present paper proposes a multi-objective approach to find out an optimal periodic maintenance policy for a repairable and stochastically deteriorating multi-component system over a finite time horizon. The tackled problem concerns the determination of the system elements to replace at each scheduled and periodical system inspection by ensuring the simultaneous minimization of both the expected total maintenance cost and the expected global system unavailability time. It is assumed that in the case of system elements failure they are instantaneously detected and repaired by means of minimal repair actions in order to rapidly restore the system. A nonlinear integer mathematical programmi…
Decay Heat Removal and Transient Analysis in Accidental Conditions in the EFIT Reactor
2008
The development of a conceptual design of an industrial-scale transmutation facility (EFIT) of several 100 MW thermal power based on accelerator-driven system (ADS) is addressed in the frame of the European EUROTRANS Integral Project. In normal operation, the core power of EFIT reactor is removed through steam generators by four secondary loops fed by water. A safety-related decay heat removal (DHR) system provided with four independent inherently safe loops is installed in the primary vessel to remove the decay heat by natural convection circulation under accidental conditions which are caused by a loss-of-heat sink (LOHS). In order to confirm the adequacy of the adopted solution for decay…
Integrated Approach to Part Scheduling and Inspection Policies for a Job Shop Manufacturing System
2007
The quality of a product greatly depends on the quality of its components. This requires that manufacturing specifications have to be met in the manufacturing environment and as a consequence inspection stations are present in many manufacturing systems and inspection policies must be adopted. One problem, which has been widely investigated, concerns the detection of the inspection points in the hypothesis that the action to be taken is known when a defective part is detected. If different jobs are to be produced, then operation scheduling becomes yet another complex problem needing to be solved. And while the problem of scheduling has received a great amount of attention from researchers, …
Residence time distribution of solid particles in a continuous, high-aspect-ratio multiple-impeller stirred vessel
2004
Abstract In this paper experimental information on the retention time distribution (RTD) of solid particles in a high-aspect-ratio vessel, stirred by three equally spaced Rushton turbines, is presented. The relevant data were obtained by a special technique named twin system approach (TSA) that greatly simplifies the handling of particle-laden streams and is therefore particularly suited for investigating particle RTD in flow systems. The technique fundamentals are first summarized, together with the data analysis procedure. This lastly requires a numerical deconvolution operation that is easily performed with the help of Z -transforms. Two different approaches for excluding the spurious co…
Design, manufacturing and testing of a fast disconnecting system for the European target assembly concept of IFMIF
2013
The International Fusion Materials Irradiation Facility (IFMIF) will be equipped with a lithium target assembly to produce the required neutron flux for the irradiation of candidate fusion materials up to a damage rate of 100 dpa (cumulated damage in five years). The present European target assembly design is based on the so called replaceable backplate bayonet concept that was developed with the objective to simplify the maintenance operations for its refurbishment/replacement and to reduce the material for disposal as well. To this purpose it was also conceived to be attached to the lithium pipes and to the beam line by means of remotely operated connections based on clamped flanges with …
Analysis of the maximization of wind turbine energy yield using a continuously variable transmission system
2017
Abstract In this paper, an analytic study of the subject of mechanical power transmission in HAWT wind turbine has been carried out. For the most part, the study analyzes the use of continuously variable transmission (CVT) in order to allow the turbine and the electric generator to couple, allowing in turn, an unremitting transmission ratio adjustment. In low-wind sites, the design criteria suggest an oversizing of the wind turbine in order to generate adequate electrical power even at low wind speed. The proposed solution enhances the space of operating points since it allows the electric generator to release the rotational speed from the turbine one (limited due to structural integrity). …
A combined multi-criteria approach to support FMECA analyses: A real-world case
2018
[EN] The paper proposes an approach that combines reliability analyses and multi-criteria decision methods to optimize maintenance activities of complex systems. A failure mode, effects, and criticality analysts (FMECA) is initially performed and the fuzzy TOPSIS (FTOPSIS) method is then applied to rank previously identified failure modes. For prioritization, failure modes are assessed against three evaluation criteria that differ from those traditionally involved in risk priority number (RPN) computation (i.e. severity, occurrence and detection). Two criteria refer to the maintenance management reflecting the operational time taken by the maintenance activity performed after the occurrence…
Analysis and simulation of scale-up potentials in reverse electrodialysis
2015
The Reverse Electrodialysis (RED) process has been widely accepted as a viable and promising technology to produce electric energy from salinity difference (salinity gradient power - e.g. using river water/seawater, or seawater and concentrated brines). Recent R&D efforts demonstrated how an appropriate design of the RED unit and a suitable selection of process conditions may crucially enhance the process performance. With this regard, a process simulator was developed and validated with experimental data collected on a lab-scale unit, providing a new modelling tool for process optimisation. In this work, performed within the REAPower project (www.reapower.eu), a process simulator previousl…
On the assessment of power consumption and critical impeller speed in vortexing unbaffled stirred tanks
2017
Abstract Unbaffled stirred tanks are increasingly recognized as a viable alternative to common baffled tanks for a number of processes and bio-processes where the presence of baffles is undesirable. Notwithstanding the increasing industrial interest towards unbaffled tanks, available experimental information on their behaviour is still very poor, even for important parameters such as mechanical power drawn and critical impeller speed (Ncr) at which the transition between non-aerated (sub-critical regime) and aerated (super-critical regime) conditions occurs. In this work the influence of Reynolds and Froude numbers on power consumption characteristics of unbaffled stirred tanks is presented…
A simulation tool for analysis and design of reverse electrodialysis using concentrated brines
2015
Abstract Reverse electrodialysis (SGP-RE or RED) represents a viable technology for the conversion of the salinity gradient power into electric power. A comprehensive model is proposed for the RED process using sea or brackish water and concentrated brine as feed solutions. The goals were (i) reliably describing the physical phenomena involved in the process and (ii) providing information for optimal equipment design. For such purposes, the model has been developed at two different scales of description: a lower scale for the repeating unit of the system (cell pair), and a higher scale for the entire equipment (stack). The model was implemented in a process simulator, validated against orig…