Search results for "INTERFACE"

Positron Annihilation Study of Defects Induced by Various Cutting Methods in Stainless Steel Grade 304

2011

We report in this article the comparison of the subsurface zones (SZs) in austenitic stainless steel 304 samples created by three cutting techniques, i.e., the laser cutting (LC), abrasive water jet (AWJ), and traditional milling cutting (MC). The crystal lattice defects distribution in this zone were investigated using the positron annihilation method. It was shown that the MC creates the great number mainly edge dislocations decorated by vacancies. Their concentration decreases with the increase of the depth from the cut surface. The total depth of the SZ is extended up to 150 μm from the cut surface. Similar dependency was observed for the AWJ machining but the total depth is much lower,…

Structural analysis of W3O/WO3 and TiO/TiO2 periodic multilayer thin films sputter deposited by the reactive gas pulsing process

2012

International audience; DC reactive sputtering was used to deposit titanium and tungsten-based metal/oxide periodic nanometric multilayers using pure metallic targets and Ar + O-2 gas mixture as reactive atmosphere. The innovative technique namely, the reactive gas pulsing process allows switching between the metal and oxide to prepare a periodic multilayered structure with various metalloid concentrations and nanometric dimensions. The same pulsing period was used for each deposition to produce metal-oxide periodic alternations close to 10 nm. Structure, crystallinity and chemical composition of these films were systematically investigated by Raman spectroscopy, X-ray diffraction and Energ…

The Annealing Behavior of the Subsurface Zone Induced by Friction in Bismuth Detected by Positron Lifetime Technique

2013

The annealing behavior of the subsurface zone (SZ) in pure bismuth induced by dry sliding was studied using the positron lifetime measurement. This measurement allows us to detect the SZ and its recovery, and recrystallization processes. The comparative measurements of the sample exposed to compression revealed the thermal stability of the SZ. The compressed sample rebuilt its structure due to the recovery and recrystallization processes at the temperature of 60 °C, whereas the sample exposed to dry sliding does it at higher temperature of 260 °C, which is close to the melting point. The isothermal annealing at the temperature of 100 °C confirmed these results. The defect depth profile indu…

Element-Selective Magnetic Imaging in Exchange-Coupled Systems by Magnetic Photoemission Microscopy

1998

We have used a photoemission microscope to obtain element-resolved magnetic contrast in stacked magnetic thin film systems. Magnetic information is thereby provided by X-ray magnetic circular dichroism. Elemental sensitivity, which is crucial for studying magnetic coupling phenomena in systems with several different layers, is achieved by tuning the energy of the illuminating photons to atomic absorption edges. We present measurements of a Ni-coated Co micropattern on Cu(001), and a wedged Co/Cr/Fe(001) sample. In the former sample the Ni magnetization is seen to follow the magnetization of the Co pattern, thereby changing from an out-of-plane easy axis in areas without underlying Co to in…

Effect of antisite defects on the magnetic properties of ZnFe2 O4

2013

Magnetic zinc ferrite (ZnFe2O4) nanopowders were synthesized using the sol–gel autocombustion method. X-ray diffraction (XRD) and scanning electron microscopy (SEM) measurements demonstrated that thermal decomposition of the 1-mm-thick xerogel layers in air formed monophasic spinel ferrite nanopowders with a particle size less than 30 nm. X-ray photoelectron spectroscopy (XPS) showed that the obtained reaction product contained antisite defects, with zinc ions occurring at the octahedral sites of the spinel structure. The concentration of antisite defects or inversion degree decreased when the relatively low annealing temperature was increased from 150 to 500 °C. Overall, the obtained ZnFe2…

Back Cover (Phys. Status Solidi A 12/2009)

2009

White Etching Crack Root Cause Investigations

2014

White etching crack (WEC) failure is distinct to classical fatigue and driven by the composition of lubricants under special loading conditions; for example, slippage and electricity. The white etching area (WEA) within WEC contains carbon supersaturated ferrite (bcc-iron) and carbides, with a size of a few nanometers. This article presents investigations supporting the hypothesis that WEC processes start within a failure-free period by successive accumulation of a structural distortion. This can be measured by acoustic emission. Failure statistics show a steep ascent in the Weibull diagram (s values beyond 1) leading to the assumption that WEC processes start unsuspicious, as one would see…

Frictional behaviour of oxygen diffusion hardened titanium in dry sliding against Co–28Cr–5W–4Fe–3Ni–1Si cobalt alloy

2004

Abstract The results of conformal pin-on-disc tribological tests of a hard layer of the solid solution of oxygen in α-titanium sliding against a Co–28Cr–5W–4Fe–3Ni–1Si cobalt alloy counterspecimen are presented. The α-Ti(O) layer was diffusely produced over 2–8 h of oxidising in the superficial zone of a technical quality titanium specimen. The friction and wear responses of the system were recorded and the wear mechanisms were studied. Investigations of the material structure and chemical constitution in micro-areas of the titanium specimen, cobalt alloy counterspecimen and wear debris formed in dry sliding were performed with a Philips XL20 microscope equipped with an EDAX analyser. Crush…

Microsphere tensiometry to measure advancing and receding contact angles on individual particles

1999

In this paper, a method to measure the advancing and receding contact angles on individual colloidal spheres is described. For this purpose, the microspheres were attached to atomic force microscope cantilevers. Then the distance to which the microsphere jumps into its equilibrium position at the air-liquid interface of a drop or an air bubble was measured. From these distances the contact angles were calculated. To test the method, experiments were done with silanized silica spheres (4.1 μm in diameter). From the experiments with drops, an advancing contact angle of 101 ± 4° was determined. A receding contact angle of 101 ± 2° was calculated from the jump-in distance into a bubble. Both ex…

Reactive sputtering of nanostructured multilayer coatings and their tribological properties

1999

Abstract The present study describes and reports on reactive sputtering of nanostructured multilayer coatings. A 3 μm coating for instance may contain up to a few thousand bilayers of two different film materials, and in order to achieve this, a substrate holder rotates through two different sputtering zones in an Alcatel SC 650 sputtering equipment with metal and carbon cathodes operating concurrently in the so-called side-by-side configuration. In reactive sputtering of nitrides, reactive nitrogen was controlled very accurately in order to establish controllable points on a total sputtering pressure versus nitrogen flow curve. Nanostructured multilayer coatings of the type MeN/C–N were de…