Search results for "InP"
showing 10 items of 508 documents
Robust control of stochastic systems against bounded disturbances with application to flight control
2014
This paper investigates the problems of state observer design and observer-based integral sliding-mode control (SMC) for a class of Itô stochastic systems subject to simultaneous input and output disturbances. A new type of sliding-mode-based descriptor observer method is developed to approximate the system state and disturbance vectors. An integral-type SMC scheme is proposed based on the state estimation to stabilize the overall system. The main contributions of this approach are as follows: 1) The desired estimations of state and disturbance vectors can be obtained simultaneously, and 2) in the designed sliding-mode observer, the integral term of the Itô stochastic noise is eliminated …
Achieving maximum power transfer in a multi-source renewable system
2014
In this paper, a multi-source DC-DC power system is proposed for renewable applications. A multi-input, single inductor power converter controlled by two interacting control loops is designed. The steady-state and small-signal analysis of the designed system is carried out. A battery-photovoltaic system is designed as an application example. Both the output voltage and maximum power point of solar panels are properly controlled to achieve high performances of the whole system. Experimental results on a 48 V laboratory prototype are presented to discuss system performances.
Assessment of methodologies and data used to calculate desalination costs
2017
Abstract In desalination, similarly with other industries, the cost of the final product is one of the most important criteria that define the commercial success of a specific technology. Therefore, when new projects are planned or new technologies are proposed, the analysis of the expected costs attracts a lot of attention and is compared to (perceived) costs of state-of-the-art desalination or costs of alternative fresh water supply options. This comparison only makes sense if the cost assessment methodologies are based on the same principles and use common assumptions. This paper assesses: (i) the methodologies used to calculate the water cost; (ii) the boundary conditions and (iii) the …
Flat panel displays for medical monitoring systems
2005
Flat panel displays are ideal for demanding hospital and clinic applications like vital sign monitoring and bedside administration. They take up much less space than conventional monitors (CRT based) and can be wall-mounted, cart-mounted or used on a desk stand. User friendly interface demands easy to use input device, rotary position encoders and touch screen panels offers simplicity replacing bulky keyboards. This article will present an overview about today's medical monitoring systems tendencies, describing as an example, a custom medical monitoring module developed to be integrated in an assisted ventilation system.
A PC-based wattmeter for accurate measurements in sinusoidal and distorted conditions: Setup and experimental characterization
2012
This paper presents the development of a high-accuracy sampling wattmeter, which can be employed with both sinusoidal and distorted input signals. The proposed personal computer (PC)-based system is a simple, portable, and low-cost solution because it is based on two commercial data acquisition boards connected to a common PC. Owing to this solution, the voltage is sensed directly, avoiding expensive voltage dividers, while the current is sensed by means of a noninductive current shunt. Commercial software is also used for data processing and implementation of the virtual instrument. The setup of the PC-based wattmeter is described, with a detailed description of the correction strategy of …
Design, fabrication, and analysis of a spin-valve based current sensor
2004
Abstract In this work, we suggest a novel current sensor design, based on spin valve technology, with a full Wheatstone bridge configuration. The principal characteristic is that the four magnetoresistance sensing elements, fully active, are deposited and patterned at the same time. This way, differences among them should be insignificant, so improving voltage offset and drift temperature parameters. The complete IC fabrication process involves only three lithography steps, making the process cheaper and faster. In order to get a balanced bridge, the measured current must be properly driven, by means of an auxiliary PCB. Some prototypes, with different input impedances, have been fabricated…
A new backward/forward method for solving radial distribution networks with PV nodes
2008
Abstract In this paper, a new backward/forward (b/f) methodology for the analysis of distribution systems with constant power loads is presented. In the proposed method, at each iteration, the loads are considered as constant impedances; in the backward sweep all the network variables (bus voltages and branch currents) are evaluated considering a scaling factor which is determined at the end of the backward phase. Indeed the forward sweep is eliminated and the node voltages calculation does not demand the sequentiality needed in the b/f methodology. The developed method, although deriving conceptually from the b/f methodology, presents only the backward phase in which all the network variab…
A robust fault detection design for uncertain Takagi-Sugeno models with unknown inputs and time-varying delays
2013
Abstract This paper investigates the problem of robust fault detection system design for a class of uncertain Takagi–Sugeno (T–S) models. The system under consideration is subject to unknown input and time-varying delay. The fault detection system is designed such that the unknown input is thoroughly decoupled from residual signals generated by the fault detection system. Furthermore, the residual signals show the maximum possible sensitivity to the faults and the minimum possible sensitivity to the external disturbances. The model matching approach is utilized to tackle the effects of parametric uncertainties in the model of the system. The design procedure is presented in terms of Linear …
Using input shaping and pressure feedback to suppress oscillations in slewing motion of lightweight flexible hydraulic crane
2015
This paper presents a method to actively reduce vibrations in the flexible mechanical structure of a hydraulically actuated vehicle loader crane. Based on information on the natural frequency and damping of a simplified model of the crane an input shaping scheme is set up to control the proportional valve leading to substantially reductions in oscillations. The method is compared and combined with a pressure feedback control of the proportional valve that actively suppresses transient variations in pressure. A full scale vehicle loader crane is used in the experimental verification of the method, and the motion of the tool point of the crane is measured by a high precision laser tracker. Th…
A DC-DC power converter for PV module characterization
2014
In this paper, a standard-compliant electronic load setup for PV module curve detection which features high accuracy, low cost and components count is proposed. The proposed device is based on a DC-DC power converter in open-loop configuration. The proposed system is designed according to regulation constraints in order to achieve high performances in curve detection. Design criteria are discussed. The model is implemented in PSIM environment. Simulation based on data input of a commercial PV Conergy E215P module are carried out under several environmental conditions to show the accuracy of the proposed electronic load. Simulation results are reported.