Search results for "Injection"

Multicenter Consistency Assessment of Valvular Flow Quantification With Automated Valve Tracking in 4D Flow CMR

2021

OBJECTIVES This study determined: 1) the interobserver agreement; 2) valvular flow variation; and 3) which variables independently predicted the variation of valvular flow quantification from 4-dimensional (4D) flow cardiac magnetic resonance (CMR) with automated retrospective valve tracking at multiple sites. BACKGROUND Automated retrospective valve tracking in 4D flow CMR allows consistent assessment of valvular flow through all intracardiac valves. However, due to the variance of CMR scanners and protocols, it remains uncertain if the published consistency holds for other clinical centers. METHODS Seven sites each retrospectively or prospectively selected 20 subjects who underwent whole …

Defending Surveillance Sensor Networks Against Data-Injection Attacks Via Trusted Nodes

2018

By injecting false data through compromised sensors, an adversary can drive the probability of detection in a sensor network-based spatial field surveillance system to arbitrarily low values. As a countermeasure, a small subset of sensors may be secured. Leveraging the theory of Matched Subspace Detection, we propose and evaluate several detectors that add robustness to attacks when such trusted nodes are available. Our results reveal the performance-security tradeoff of these schemes and can be used to determine the number of trusted nodes required for a given performance target.

Improving the multiple errors detection coverage in distributed embedded systems

2004

Currently, a lot of critical applications in automobile and aircraft avionics are built on fault-tolerant real-time distributed embedded systems. Fault injection techniques have been used extensively in the experimental validation of these systems and it is a challenge to adapt them to the demands of new technologies. This paper deals with the effect of physical faults at pin level on the Communication Network Interface in a prototype based on time-triggered architecture. Due to the essential necessity of observing system behavior during injection experiments, a suitable monitor for distributed embedded systems is proposed. The monitor is used to detect failures in the value domain that cou…

Injection pressure mapping of intraneural vs. perineural injections: further lessons from cadaveric studies.

2018

Background The aim of the study was to investigate the difference between intraneural and perineural injection pressures in human cadavers. Targeted nerves included the cervical roots, the supraclavicular and infraclavicular brachial plexus, the sciatic-subgluteal nerve and the common peroneal and tibial nerves. Methods Ten readings were obtained for each nerve location. Over ten seconds, 1 mL of 0.9% NaCl was injected - deliberately slower than in clinical practice to eliminate the risk of aberrant readings relating to the speed of injection. Perineural injections occurred at least 1 mm outside the epineurium. After pressure recordings were completed 0.1mL of dye was injected, and dissecti…

Intra-cardiac Signatures of Atrial Arrhythmias Identified by Machine Learning and Traditional Features

2021

Intracardiac devices separate atrial arrhythmias (AA) from sinus rhythm (SR) using electrogram (EGM) features such as rate, that are imperfect. We hypothesized that machine learning could improve this classification.

Natural oxygenation of Champagne wine during ageing on lees: A metabolomics picture of hormesis

2016

International audience; The oxygenation of Champagne wine after 4 and 6 years of aging on lees in bottle was investigated by FTICR-MS and UPLC-Q-TOF-MS. Three levels of permeability were considered for the stoppers, ranging from 0.2 to 1.8 mg/L/year of oxygen transfer rate. Our results confirmed a good repeatability of ultrahigh resolution FTICR-MS, both in terms of m/z and coefficient of variation of peak intensities among biological replicates. Vintages appeared to be the most discriminated features, and metabolite annotations suggested that the oldest wines (2006) were characterized by a higher sensitivity towards oxygenation. Within each vintage, the oxygenation mechanisms appeared to b…

The use of morphokinetics as a predictor of embryo implantation.

2011

Background Time-lapse observation presents an opportunity for optimizing embryo selection based on morphological grading as well as providing novel kinetic parameters, which may further improve accurate selection of viable embryos. The objective of this retrospective study was to identify the morphokinetic parameters specific to embryos that were capable of implanting. In order to compare a large number of embryos, with minimal variation in culture conditions, we have used an automatic embryo monitoring system. Methods Using a tri-gas IVF incubator with a built-in camera designed to automatically acquire images at defined time points, we have simultaneously monitored up to 72 individual emb…

Preparative separation of proteins and enzymes in the mean molecular-weight range of 10,000–100,000 LiChrosorb diol® packing by high-performance size…

1979

Abstract LiChrossorb Diol® packing has been to be well-suited for the separation of proteins and enzymes according to a size-exclusion mechanism in a mean molecular-weight (MW) range between 10,000 and 100,000. Loadability of a small bore column of 6 mm I.D. (A) and a large-bore column of 23.5 mm I.D. (B), both of 250 mm in length, were examined. Defining a 20% decrease of the number of theoretical plates as loadability limit the volume load at constant mass of chymotrypsinogen as representative test solute was ≈ 100 μl for column (A) and 1500 μl for column B at 0.78 · 10-5 g/g of packing for column A and 0.78 · 10-6 g/g of packing for column B, respectively. Mass load to constant injection…

Optimization of Polymer Blue-Light-Emitting Devices by Introducing a Hole-Injection Layer Doped with the Molecular Nanomagnet [Mn12O12(H2O)4(C6F5COO)…

2006

Characterization of a fiber reinforced semirigid liquid crystalline polymer

1997

In this work, samples of a semirigid Liquid crystalline polymer reinforced with carbon and glass fibers has been characterized. Semirigid liquid crystalline polymers (LCPs) show some advantages with respect to rigid LCPs: in particular lower processing temperatures, and better compatibility with flexible thermoplastics, but also some disadvantages: lower mechanical properties and poor thermomechanical resistance. Both properties can be improved by adding inorganic fillers. Although elastic modulus and tensile strength of the glass fiber filled LCP improve remarkably with increasing the filler content, the same properties for the carbon fiber-filled samples do not increase with increasing ti…