Search results for "Instrumentation"
showing 10 items of 4914 documents
Acoustic properties of plates with unevenly distributed macro perforations backed by woven meshes
2012
A hybrid model describing the acoustic properties of plates with macro-perforations that can be unevenly distributed on the plate surface and backed by woven or precision woven meshes with microscopic perforations is proposed. The plate perforations may be of circular or rectangular shapes. Since the perforated plate may not necessarily be considered as an equivalent fluid, its surface impedance is calculated by the Maa model [Noise Control Eng. J. 29, 77-84 (1987)], whereas the Johnson-Champoux-Allard model [J. Appl. Phys. 70, 1975-1979 (1991)] is used for the mesh. It is observed that the absorption of the carrying plate seems to depend on the hydraulic diameter of the perforations and no…
Gas sensors arrays (electronic noses) : a study about the speed/accuracy ratio
2000
Abstract New Fingerprint Mass Spectra (FMS) systems claim for a higher precision, a reduced analysis time, and a lower drift, compared with Gas Sensors Arrays ‘Electronic Noses’. We demonstrated in this study that metal oxide gas sensors may have highly improved performances for both accuracy and run time, when used in optimum conditions. The different noise components were quantified referring to popular words (equivalent of ethanol concentration) using the transfer function of the sensor. It was pointed out that sample surrounding greatly affects the noise level, and that the signal-to-noise ratio may be dramatically increased, reducing the distortion generally assessed between sensor and…
Noise Analysis and Comparison of Phase-and Frequency-Detecting Readout Systems: Application to SAW Delay Line Magnetic Field Sensor
2019
International audience; Transmission surface acoustic wave (SAW) sensors are widely used in various fields of application. In order to improve the limit of detection (LOD) of such sensor systems, it is essential to understand and quantify the relevant noise sources. Only then, strategies for noise reduction can be developed. In this paper, low noise readout systems for the application with SAW sensors in an open-loop and a closed-loop configuration are presented and experimentally investigated with regard to their phase noise on the example of a SAW delay line magnetic field sensor. Besides a comprehensive analysis of the phaseand frequency modulated signals, respectively, previously derive…
Electronic noses : specify or disappear
2000
Abstract When the quality control is achieved by using GC or GC/MS, the apparatus must comply with the applicable norms, but what about “electronic noses”? End users demand for formal specifications for selectivity, sensitivity, repeatability and sample throughput. The behavioural modelling of electronic olfactometers may provide specifications for these required parameters. This will allow both the measure itself, and evaluate the influence of the experimental errors on the sample classification. Users may expect to find a methodology allowing the performances of systems to be checked before any final decision and during routine use. We have demonstrated that the system sensitivity and log…
Influence of interfering gases on a carbon monoxide differential sensor based on SAW devices functionalized with cobalt and copper corroles
2021
International audience; <!--[if gte mso 9]><xml> <w:WordDocument> <w:View>Normal</w:View> <w:Zoom>0</w:Zoom> <w:TrackMoves/> <w:TrackFormatting/> <w:HyphenationZone>21</w:HyphenationZone> <w:PunctuationKerning/> <w:ValidateAgainstSchemas/> <w:SaveIfXMLInvalid>false</w:SaveIfXMLInvalid> <w:IgnoreMixedContent>false</w:IgnoreMixedContent> <w:AlwaysShowPlaceholderText>false</w:AlwaysShowPlaceholderText> <w:DoNotPromoteQF/> <w:LidThemeOther>FR</w:LidThemeOther> <w:Compatibility> <w:BreakWrappedTables/> <w:SnapToGridInCell/> <w:WrapTextWithPunct/> <w:UseAsianBreakRules/> <w:DontGrowAutofit/> <w:SplitPgBreakAndParaMark/> <w:EnableOpenTypeKe…
Noise characterization of analog to digital converters for amplitude and phase noise measurements
2017
International audience; Improvements on electronic technology in recent years have allowed the application of digital techniques in phase noise metrology where low noise and high accuracy are required, yielding flexibility in systems implementation and setup. This results in measurement systems with extended capabilities, additional functionalities and ease of use. In most digital schemes the Analog to Digital Converters (ADCs) set the ultimate performance of the system, therefore the proper selection of this component is a critical issue. Currently, the information available in literature describes in depth the ADC features only at frequency offsets far from the carrier. However, the perfo…
Equivalence of Open-Loop and Closed-Loop Operation of SAW Resonators and Delay Lines
2019
International audience; Surface acoustic wave (SAW) sensors in the form of two-port resonators or delay lines are widely used in various fields of application. The readout of such sensors is achieved by electronic systems operating either in an open-loop or in a closed-loop configuration. The mode of operation of the sensor system is usually chosen based on requirements like, e.g., bandwidth, dynamic range, linearity, costs, and immunity against environmental influences. Because the limit of detection (LOD) at the output of a sensor system is often one of the most important figures of merit, both readout structures, i.e., open-loop and closed-loop systems, are analyzed in terms of the minim…
Residual Phase Noise Measurement of Optical Second Harmonic Generation in PPLN Waveguides
2017
We report on the characterization, including residual phase noise and fractional frequency instability, of fiber-coupled PPLN non-linear crystals. These components are devoted to frequency doubling 871 nm light from an extended-cavity diode laser to produce a 435.5 nm beam, corresponding to the ytterbium ion electric quadrupole clock transition. We measure doubling efficiencies of up to 117.5 %/W. Using a Mach-Zehnder interferometer and an original noise rejection technique, the residual phase noise of the doublers is estimated to be lower than ${\rm -35\, dBrad^2/Hz}$ at 1 Hz, making these modules compatible with up-to-date optical clocks and ultra-stable cavities. The influence of externa…
Phase-Noise and Amplitude-Noise Measurement of DACs and DDSs
2019
This article proposes a method for the measurement of Phase Noise (PN, or PM noise) and Amplitude Noise (AN, or AM noise) of Digital-to-Analog Converters (DAC) and Direct Digital Synthesizers (DDS) based on modulation-index amplification. The carrier is first reduced by a controlled amount (30-40 dB) by adding a reference signal of nearly equal amplitude and opposite in phase. Then, residual carrier and noise sidebands are amplified and sent to a conventional PN analyzer. The main virtues of our method are: (i) the noise specs of the PN analyzer are relaxed by a factor equal to the carrier suppression ratio; and, (ii) the capability to measure the AN using a PN analyzer, with no need for th…
Frequency Stability Measurement of Cryogenic Sapphire Oscillators with a Multichannel Tracking DDS and the Two-Sample Covariance
2018
This article shows the first measurement of three 100 MHz signals exhibiting fluctuations from 2E-16 to parts in 1E-15 for integration time tau between 1 s and 1 day. Such stable signals are provided by three Cryogenic Sapphire Oscillators (CSOs) operating at about 10 GHz, also delivering the 100 MHz output via a dedicated synthesizer. The measurement is made possible by a 6-channel Tracking DDS (TDDS) and the two-sample covariance tool, used to estimate the Allan variance. The use of two TDDS channels per CSO enables high rejection of the instrument background noise. The covariance outperforms the Three-Cornered Hat (TCH) method in that the background converges to zero "out of the box," wi…