Search results for "Instrumentation"

Parameter identification of induction motor model using genetic algorithms

1998

The paper deals with methods of identification of the parameters of an induction motor model using genetic algorithms. It is supposed that the inverter supplying the motor is directly accessible for control of the conduction sequences of its power switches. This makes it possible to carry out a test consisting of a transient from standstill to steady-state operation at a given frequency and successive free motion to standstill. During this test, data are acquired referring to stator voltages, and currents and speed. Then, a genetic algorithm is employed with the aim of determining the mechanical and electrical parameters of the model, so as to reproduce the input-output behaviour of a real …

A novel approach to current transformer characterization in the presence of harmonic distortion

2009

The current transformer (CT) performance under distorted waveform conditions is usually characterized by means of the frequency-response test. In this paper, a new way to characterize CTs, closer to real operation conditions, is proposed. The harmonic phase-angle and ratio errors are measured using a nonsinusoidal current composed of fundamental and one harmonic with adjustable phase shift. The new method was tested by determining the performance of two metering class CTs commonly used by the Italian power company. The errors measured using the proposed approach are larger than the ones obtained with the frequency response. This result suggests that the frequency-response approach for the e…

Oil filled MV/LV Power Transformer Behavior in Narrow Band Power Line Communication Systems

2012

The aim of this paper is to characterize oil-filled power transformers in the narrow-band power-line communication (PLC) frequency range of 50-150 kHz. A new model is proposed for such type of a transformer, in the aforementioned frequency range of interest, in order to study its influence on the signal transmission and to investigate the possibility that the PLC signal can cross the power transformer itself. The new model is simpler than those previously proposed in literature, and it can be used in the whole frequency range available for NB PLC according to the CENELEC EN 50065-1 A-band. In order to validate the model, simulation and measurement results are compared for four oil-filled po…

Remote Sensing Master and Doctorate (PhD) at the Valencia University, Spain [Education]

2014

Proposal of geographic information systems methodology for quality control procedures of data obtained in naturalistic driving studies

2015

The primary goal of naturalistic driving studies is to provide a comprehensive observation of the driver's behaviour under real-life conditions by measureing a great number of parameters at high temporal frequencies. Achieving this goal, however, is a complex endeavor that faces many challenges such as the complexity of the vehicle instrumentation during the phase of data collection, and the difficult handling of large data volumes during the phase of data analysis. These drawbacks often cause episodes of data losses. Improving the technical aspects of the collection of naturalistic data is of paramount importance to increase the return of the investment made in it. An aspect to consider is…

Instrumentation, control, and automation for submerged anaerobic membrane bioreactors

2015

A submerged anaerobic membrane bioreactor (AnMBR) demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON® , Koch Membrane Systems, PUR-PSH31) was designed and operated for urban wastewater treatment. An instrumentation, control, and automation (ICA) system was designed and implemented for proper process performance. Several single-input-single-output (SISO) feedback control loops based on conventional on off and PID algorithms were implemented to control the following operating variables: flow-rates (influent, permeate, sludge recycling and wasting, and recycled biogas through both reactor and membrane tanks), sludge wasting volume, temperature, transmembrane pr…

Low-cost underwater navigation systems by multi-pressure measurements and AHRS data

2017

This paper deals with accurate navigation for underwater remotely operated vehicles. A feasibility study for a multi-pressure device to be mounted on an ROV is presented. The device can provide accurate estimates of a ROV orientation and angular speed. It is based on the well-known total pressure principle, also used in a Pitot tube, and allows reconstruction of static and dynamic pressures, which in turn provide good estimates of the ROV's orientation and rotational speed, respectively. An appealing feature of the proposed device is its ability to provide accurate estimates even for low-speed movements.

Synchronization techniques for power quality instruments

2004

The measurement of voltage characteristics in power systems requires the accurate estimation of the power supply frequency and signal synchronization, even in the presence of disturbances. The authors developed and tested two innovative techniques for instrument synchronization. The first is based on signal spectral analysis techniques performed by means of the Chirp-Z transform analysis. The second is a phase-locked loop (PLL) software based on a time-domain coordinate transformation and an innovative phase-detection technique. To evaluate how synchronization techniques are adversely affected by the application of a disturbing influence, experimental tests were carried out, taking into acc…

Integrating Manufacturing Equipments Using a Shop Floor Control System

2006

A generic manufacturing system must interact with an environment characterized by a strong competition and by continuous technological changes. For this reason there is the necessity to make the system easily and economically modifiable in its hardware and software configuration. One of the main problems in making a manufacturing system re-configurable concerns its control system which has to be accordingly scalable and object oriented. This paper presents a methodology for making a manufacturing control system actually reconfigurable and adaptable to hardware changes in the manufacturing systems components. In particular, a PC-based shop-floor control system has been realized. Such system …

Mechanical construction and installation of the ATLAS tile calorimeter

2013

This paper summarises the mechanical construction andinstallation of the Tile Calorimeter for the ATLASexperiment at the Large Hadron Collider in CERN, Switzerland. The TileCalorimeter is a sampling calorimeter using scintillator as the sensitivedetector and steel as the absorber and covers the central region of the ATLASexperiment up to pseudorapidities ±1.7. The mechanical construction ofthe Tile Calorimeter occurred over a periodof about 10 years beginning in 1995 with the completionof the Technical Design Report and ending in 2006 with the installationof the final module in the ATLAS cavern. Duringthis period approximately 2600 metric tons of steel were transformedinto a laminated struc…