Search results for "Instrumentation"
showing 10 items of 4914 documents
Method for designing PI-type fuzzy controllers for induction motor drives
2001
The paper illustrates a new systematic method for designing PI-type fuzzy controllers for direct field-oriented controlled induction motor drives. First, linear and decoupled models expressing the dynamics of speed, rotor flux, direct and inquadrature stator currents are derived using a nonlinear static compensator and choosing convenient input variables. Then, to guide the dynamics of the above quantities, four conventional PI controllers are designed independently, choosing their bandwidths conveniently. Finally, the input and output scale factors of PI-type fuzzy controllers are derived from the conventional PI controller parameters. The whole drive controller also includes a rotor flux …
Development of a high-accuracy PC-based wattmeter with commercial data acquisition boards
2011
This paper presents the development of a high accuracy sampling wattmeter, which makes use of two commercial data acquisition boards (DAQs) connected to a common personal computer. Commercial software is also used for data processing and implementation of the virtual instrument. The set up of the PC-based wattmeter is described and a preliminary evaluation of its metrological performances is made by means of two series of experimental tests, which were carried out with an electric power standard and a high performance multifunction calibrator. © 2011 IEEE.
A PC-based wattmeter for accurate measurements in sinusoidal and distorted conditions: Setup and experimental characterization
2012
This paper presents the development of a high-accuracy sampling wattmeter, which can be employed with both sinusoidal and distorted input signals. The proposed personal computer (PC)-based system is a simple, portable, and low-cost solution because it is based on two commercial data acquisition boards connected to a common PC. Owing to this solution, the voltage is sensed directly, avoiding expensive voltage dividers, while the current is sensed by means of a noninductive current shunt. Commercial software is also used for data processing and implementation of the virtual instrument. The setup of the PC-based wattmeter is described, with a detailed description of the correction strategy of …
Virtual Instruments: Uncertainty Evaluation in the Presence of Electromagnetic Interferences
2007
The electromagnetic interferences can influence the performances of a virtual instrument; consequently, in a generic measurement performed by using these instruments, the related uncertainty values can increase. In the paper, we report the results of various experimental tests performed with the aim to check if and how the radiated and/or conducted disturbances affect the instruments' characteristics and, in particular, the single uncertainty sources. Starting from these results and applying an already proposed method for the uncertainty estimation in the measurements performed by means of virtual instruments, it is possible to take into account and to evaluate the contribute of the electro…
Greening island: Renewable energies mix to satisfy electrical needs of Pantelleria in Mediterranean sea
2016
In this article the authors analyze the renewable mix in order to satisfy the energy needs of a real island in the Mediterranean sea, Pantelleria, which represents an optimal starting point to increase the production of electrical energy from renewable sources in minor islands. In this text are exposed different alternative sources, such as solar, wind and wave energy. Moreover, it is exposed a project of an innovative conversion device proposed by Department of Energy of University of Palermo, compared to a different one proposed by Politecnico di Torino. The procedures applied in the present article, as well as the main equations used, are the result of previous applications made in diffe…
A tunnel magnetoresistive effect wattmeters-based wireless sensors network
2017
Abstract In the present work a wireless sensors network (WSN) for smart energy metering is presented using the ZigBee protocol as the communication link. Each network node process the electrical power by means of a Wheatstone bridge sensor based on the tunnel magnetoresistive (TMR) effect working as analogue multiplier. The electrical power is acquired and processed by a digital signal processor that extracts various parameters of interest like current and voltage load, active power and power factor by means of Fourier analysis. All the obtained electrical parameters at each node are served and shown in a web page that can be easily accessed by authorized users.
Design, fabrication, and analysis of a spin-valve based current sensor
2004
Abstract In this work, we suggest a novel current sensor design, based on spin valve technology, with a full Wheatstone bridge configuration. The principal characteristic is that the four magnetoresistance sensing elements, fully active, are deposited and patterned at the same time. This way, differences among them should be insignificant, so improving voltage offset and drift temperature parameters. The complete IC fabrication process involves only three lithography steps, making the process cheaper and faster. In order to get a balanced bridge, the measured current must be properly driven, by means of an auxiliary PCB. Some prototypes, with different input impedances, have been fabricated…
A Non-Invasive Thermal Drift Compensation Technique Applied to a Spin-Valve Magnetoresistive Current Sensor
2011
A compensation method for the sensitivity drift of a magnetoresistive (MR) Wheatstone bridge current sensor is proposed. The technique was carried out by placing a ruthenium temperature sensor and the MR sensor to be compensated inside a generalized impedance converter circuit (GIC). No internal modification of the sensor bridge arms is required so that the circuit is capable of compensating practical industrial sensors. The method is based on the temperature modulation of the current supplied to the bridge, which improves previous solutions based on constant current compensation. Experimental results are shown using a microfabricated spin-valve MR current sensor. The temperature compensati…
Active power analog front-end based on a Wheatstone-type magnetoresistive sensor
2011
Abstract In the proposed work a practical magnetoresistive wattmeter based on a commercial sensor is designed to measure active power at industrial frequencies. The electronic conditioning circuit uses differential blocks in order to preserve the sensor initial common mode rejection ratio. A 700 W power level has been reached with an uncertainty less than 1%. With few changes the proposed circuitry could be used in metering applications.
New method for real-time dynamic focusing through interfaces
2013
[EN] In nondestructive evaluation (NDE) a coupling medium (wedge) is frequently inserted between the array probe and the object being evaluated. In this situation, focal law computing is complicated by the refraction effects at the interface. Furthermore, there are not known techniques to perform dynamic focusing by hardware in these conditions. This work addresses these problems by following a two-step procedure. First, a virtual array that operates in a single medium with nearly equivalent time-of-flight to the foci is obtained. Then, simple hardware is proposed to perform dynamic focusing in real-time. It operates with arrays of any geometry as required by the virtual array in presence o…