Search results for "Isotropic"
showing 10 items of 128 documents
Optimisation of TA6V alloy surface laser texturing using an experimental design approach
2008
International audience; Active surfaces of plastic injection moulds are nowadays textured using classical techniques (chemical etching or EDM). Replacement of these technologies by a laser technology introduces a big flexibility: absence of mechanical contact with the tool, decrease of the effluent's volume and a big machining precision, even in the case of the complex forms as injection moulds for example. This paper reports the experimental study of the surface laser texturing of TA6V alloy. The influence of the operating factors on the laser texturing process has been studied using two experimental approaches: Taguchi methodology and response surface methodology (RSM). Empirical models h…
The effect of substrate roughness on the static friction of CuO nanowires
2012
Abstract The dependence of static friction on surface roughness was measured for copper oxide nanowires on silicon wafers coated with amorphous silicon. The surface roughness of the substrate was varied to different extent by the chemical etching of the substrates. For friction measurements, the nanowires (NWs) were pushed by an atomic-force microscope (AFM) tip at one end of the NW until complete displacement of the NW was achieved. The elastic bending profile of a NW during this manipulation process was used to calculate the ultimate static friction force. A strong dependence of static friction on surface roughness was demonstrated. The real contact area and interfacial shear strength wer…
Ultrathin silicon nanowires for optical and electrical nitrogen dioxide detection
2021
The ever-stronger attention paid to enhancing safety in the workplace has led to novel sensor development and improvement. Despite the technological progress, nanostructured sensors are not being commercially transferred due to expensive and non-microelectronic compatible materials and processing approaches. In this paper, the realization of a cost-effective sensor based on ultrathin silicon nanowires (Si NWs) for the detection of nitrogen dioxide (NO2) is reported. A modification of the metal-assisted chemical etching method allows light-emitting silicon nanowires to be obtained through a fast, low-cost, and industrially compatible approach. NO2 is a well-known dangerous gas that, even wit…
Microstructure of freestanding single-crystalline Ni2MnGa thin films
2011
Abstract The complex crystal structure and variant distribution of single-crystalline freestanding Ni–Mn–Ga films was studied in detail using X-ray diffraction in two- and four-circle geometry. Selective chemical etching of a chromium buffer layer facilitates the release of the rigid MgO substrate that would inhibit magnetically induced reorientation (MIR) of variants. The substrate-constrained as well as the freestanding films possess identical crystal structure featuring a seven-layered (pseudo-)orthorhombic modulation (7 M/14 M). Of the 12 different variants observed before and after releasing the film from the substrate, four are predominantly represented. These have the short c -axis a…
Semiflexible Polymers in the Bulk and Confined by Planar Walls
2016
Semiflexible polymers in solution under good solvent conditions can undergo an isotropic-nematic transition. This transition is reminiscent of the well-known entropically-driven transition of hard rods described by Onsager’s theory, but the flexibility of the macromolecules causes specific differences in behavior, such as anomalous long wavelength fluctuations in the ordered phase, which can be understood by the concept of the deflection length. A brief review of the recent progress in the understanding of these problems is given, summarizing results obtained by large-scale molecular dynamics simulations and density functional theory. These results include also the interaction of semiflexib…
Dislocation interaction with C in α-Fe: a comparison between atomic simulations and elasticity theory
2008
International audience; The interaction of C atoms with a screw and an edge dislocation is modelled at an atomic scale using an empirical Fe-C interatomic potential based on the Embedded Atom Method (EAM) and molecular statics simulations. Results of atomic simulations are compared with predictions of elasticity theory. It is shown that a quantitative agreement can be obtained between both modelling techniques as long as anisotropic elastic calculations are performed and both the dilatation and the tetragonal distortion induced by the C interstitial are considered. Using isotropic elasticity allows to predict the main trends of the interaction and considering only the interstitial dilatatio…
Boundary element modeling and analysis of adhesive bonded structural joints
2007
In this paper, a boundary element technique for modeling and analysis of adhesive bonded structural joints is presented. The formulation is developed in the framework of the anisotropic elasticity and attention is focused on the application to composite structural joints built with the splicing concept technique. To model and analyze composite bonded joints a multidomain implementation of the boundary element method has been used. It has been proven well suited and very effective for the characterization of the mechanical behavior of spliced joints, allowing the analysis of the high gradient stress and strain fields near the splice lines as well as the prediction of the overall distribution…
Monotonic solution of flow and transport problems in heterogeneous media using Delaunay unstructured triangular meshes
2013
Transport problems occurring in porous media and including convection, diffusion and chemical reactions, can be well represented by systems of Partial Differential Equations. In this paper, a numerical procedure is proposed for the fast and robust solution of flow and transport problems in 2D heterogeneous saturated media. The governing equations are spatially discretized with unstructured triangular meshes that must satisfy the Delaunay condition. The solution of the flow problem is split from the solution of the transport problem and it is obtained with an approach similar to the Mixed Hybrid Finite Elements method, that always guarantees the M-property of the resulting linear system. The…
Inverse problems for elliptic equations with power type nonlinearities
2021
We introduce a method for solving Calder\'on type inverse problems for semilinear equations with power type nonlinearities. The method is based on higher order linearizations, and it allows one to solve inverse problems for certain nonlinear equations in cases where the solution for a corresponding linear equation is not known. Assuming the knowledge of a nonlinear Dirichlet-to-Neumann map, we determine both a potential and a conformal manifold simultaneously in dimension $2$, and a potential on transversally anisotropic manifolds in dimensions $n \geq 3$. In the Euclidean case, we show that one can solve the Calder\'on problem for certain semilinear equations in a surprisingly simple way w…
The Linearized Calderón Problem in Transversally Anisotropic Geometries
2017
In this article we study the linearized anisotropic Calderon problem. In a compact manifold with boundary, this problem amounts to showing that products of harmonic functions form a complete set. Assuming that the manifold is transversally anisotropic, we show that the boundary measurements determine an FBI type transform at certain points in the transversal manifold. This leads to recovery of transversal singularities in the linearized problem. The method requires a geometric condition on the transversal manifold related to pairs of intersecting geodesics, but it does not involve the geodesic X-ray transform which has limited earlier results on this problem.