Search results for "JOINT"

Analysis of Joint Quality along Welding Plane

2009

Porthole die extrusion is an always more important process for industrial applications. It is, however, characterized by a considerable complexity; in fact, different parameters have to be carefully set for improving the final part. A critical zone that strongly influences the goodness of the extruded component is the so called “welding plane”. It is the junction area where material flows converge inside the welding chamber. The variables that have to be controlled for improving the material characteristics in this zone are the effective stress, the pressure and the time that the material takes to cross the welding chamber. Moreover, material temperature is another fundamental issue that in…

Experimental and numerical analysis of aluminum-aluminum bolted joints subject to an indentation process

2015

Abstract The increasing interest of the industry (especially automotive, aviation and marine) in the fastener joints (riveted, bolted, etc.) between metallic materials, has re-opened the study on the possibility to improve the performance of the drilled structure using plastic deformation processes. Indentation process, performed before the drilling operation, creates circumferential compression stresses around the hole which increase significantly the mechanical performance of the drilled structures. In this paper, static and the fatigue performances of aluminum–aluminum (AW 6082-T6) single-lap bolted joints are studied. In particular, the study compares the mechanical strength of only dri…

The Two Types of Oxygen Interstitials in Neutron‐Irradiated Corundum Single Crystals: Joint Experimental and Theoretical Study

2021

On the self-piercing riveting of aluminium blanks and carbon fibre composite panels

2010

In the present paper the possibility to join aluminium alloys blanks and carbon fibre composites panels by self-piercing riveting operation is considered. In particular a few case studies were carried out at the varying of the process parameters. The effectiveness of the obtained joints was tested through tensile tests and through fatigue ones; what is more the process mechanics was highlighted through proper macro and micro observations of the transverse sections of the joints. The failure mechanics of the obtained joints were also considered in order to highlight the mechanisms which occur and determine the lost of the load carrying capability of the joints. Finally a numerical model of t…

Friction based Solid State Welding Techniques for Transportation Industry Applications

2014

Abstract Solid bonding based processes represent an effective solution in terms of both joints mechanical performances and sustainability. In the last years, both the academic and the industrial researchers focused their work on two solid-state processes: Friction Stir Welding (FSW) and Linear Friction Welding (LFW). The former, patented in 1991 by TWI, is used to weld sheet metal in different joint morphologies, i.e. butt, lap T and 3D joints. The latter has been known for several years, but a growing interest is observed in the last years due to the enhancement of the welding machines performances. LFW, used to join bulk components, is particularly suited for aeronautical and aerospace ap…

An aging evaluation of the bearing performances of glass fiber composite laminate in salt spray fog environment

2019

The aim of the present paper is to assess the bearing performance evolution of pinned, glass-composite laminates due to environmental aging in salt-spray fog tests. Glass fibers/epoxy pinned laminates were exposed for up to 60 days in salt-spraying, foggy environmental conditions (according to ASTM B117 standard). In order to evaluate the relationship between mechanical failure mode and joint stability over increasing aging time, different single lap joints, measured by the changing hole diameter (D), laminate width (W) and hole free edge distance (E), were characterized at varying aging steps. Based on this approach, the property-structure relationship of glass-fibers/epoxy laminates was a…

Experimental Characterization of the Human Meniscal Tissue

2018

The meniscus plays a critical role in load transmission, stability and energy dissipation in the knee joint. Loss of the meniscus leads to joint degeneration and osteoarthritis. In a number of cases replacement of the resected meniscal tissue by a synthetic implant might avoid the articular cartilage degeneration. None of the available implants presents optimal biomechanics characteristic due to the fact the biomechanics functionality of the meniscus is not yet fully understood. Mimicking the native biomechanical characteristics of the menisci seems to be the key factor in meniscus replacement functioning. This is extremely challenging due to its complex inhomogeneous microstructure, the la…

A new dynamic identification technique: application to the evaluation of the equivalent strut for infilled frames

2003

A new time domain identification technique for systems under Gaussian white noise input is presented, requiring for its application the measurement of the system response but no information about input intensity. The technique proposed is based on the statistic moment equations derived by using a special class of mathematical models named "potential models". These models allow one to determine fundamental properties of the response statistics, making it possible to identify stiffness and dissipation features of a structural system, and also to determine the excitation input. The technique proposed is here applied to the identification of the strut equivalent to the infill of a single story-…

Partial joint processing with efficient backhauling using particle swarm optimization

2012

In cellular communication systems with frequency reuse factor of one, user terminals (UT) at the cell-edge are prone to intercell interference. Joint processing is one of the coordinated multipoint transmission techniques proposed to mitigate this interference. In the case of centralized joint processing, the channel state information fed back by the users need to be available at the central coordination node for precoding. The precoding weights (with the user data) need to be available at the corresponding base stations to serve the UTs. These increase the backhaul traffic. In this article, partial joint processing (PJP) is considered as a general framework that allows reducing the amount …

Constrained Clusterwise Linear Regression

2005

In market segmentation, Conjoint Analysis is often used to estimate the importance of a product attributes at the level of each single customer, clustering, successively, the customers whose behavior can be considered similar. The preference model parameter estimation is made considering data (usually opinions) of a single customer at a time, but these data are usually very few as each customer is called to express his opinion about a small number of different products (in order to simplify his/her work). In the present paper a Constrained Clusterwise Linear Regression algorithm is presented, that allows simultaneously to estimate parameters and to cluster customers, using, for the estimati…