Search results for "LESS"
showing 10 items of 2452 documents
Joining Ti6Al4V and AISI 304 through friction stir welding of lap joints: experimental and numerical analysis
2014
The results of an experimental and numerical analysis on Friction Stir Welding of dissimilar lap joints made out of AISI304 and Ti-6Al-4 V thin sheets are presented. The mixed joints, welded with varying process parameters, have been characterized from a mechanical and metallurgical point of view. A numerical model able to take into account the behaviour of the two different materials has been used. The numerical results have been utilized to explain the joint properties and the occurring material flow. The effect of the heat input, tilt angle and sheets mutual position has been investigated. It is found that both hooking defects and tunnels may occur with incorrect choice of process parame…
Topological insulators and thermoelectric materials
2012
Topological insulators (TIs) are a new quantum state of matter which have gapless surface states inside the bulk energy gap. Starting with the discovery of two dimensional TIs, the HgTe-based quantum wells, many new topological materials have been theoretically predicted and experimentally observed. Currently known TI materials can possibly be classified into two families, the HgTe family and the Bi2Se family. The signatures found in the electronic structure of a TI also cause these materials to be excellent thermoelectric materials. On the other hand, excellent thermoelectric materials can be also topologically trivial. Here we present a short introduction to topological insulators and the…
Study of the Hydrogen Embrittlement Sensitivity of an X4CrNiMo 16.5.1 Stainless Steel and the Associated Electron Beam Weld
2015
X4CrNiMo 16.5.1 steel (commercial name APX4) is a low carbon martensitic stainless steel known for its remarkable mechanical characteristics and its good resistance to corrosion. The use of APX4 in the manufacture of high pressure gas vessels requires a thorough understanding of its resistance to Hydrogen Embrittlement (HE) as the gas can contain traces of hydrogen, and martensitic steels, and their welds, are generally very sensitive to HE. This paper deals with the first part of this study, involving the characterization of the microstructure and the mechanical properties of each zone of the electron beam weld (melted zone and four different heat affected zones), and the investigation of …
Programmable proximity aperture lithography with MeV ion beams
2008
A novel MeV ion beam programmable proximity aperture lithography system has been constructed at the Accelerator Laboratory of the University of Jyvaskyla, Finland. This facility can be used to fabricate three dimensional microstructures in thick (<100μm) polymer resist such as polymethylmethacrylate. In this method, MeV ion beams from the 1.7 MV pelletron and K130 cyclotron accelerators are collimated to a beam spot of rectangular shape. This shape is defined by a computer-controlled aperture made of a pair of L-shaped Ta blades which are in close proximity to the sample to minimize the penumbra broadening. Here the authors report on development of the system, the controlling software, the …
Positron Annihilation Study of Defects Induced by Various Cutting Methods in Stainless Steel Grade 304
2011
We report in this article the comparison of the subsurface zones (SZs) in austenitic stainless steel 304 samples created by three cutting techniques, i.e., the laser cutting (LC), abrasive water jet (AWJ), and traditional milling cutting (MC). The crystal lattice defects distribution in this zone were investigated using the positron annihilation method. It was shown that the MC creates the great number mainly edge dislocations decorated by vacancies. Their concentration decreases with the increase of the depth from the cut surface. The total depth of the SZ is extended up to 150 μm from the cut surface. Similar dependency was observed for the AWJ machining but the total depth is much lower,…
Developing a procedure to optimize electroless deposition of thin palladium layer on anodic alumina membranes
2006
In recent years, the increased demand for hydrogen in many industrial applications, like petrochemical and semiconductor processing, and sustainable energy (fuel cells) has led to a renewed interest in methods for separation and purification of hydrogen from gas mixtures. In particular, palladium-based membranes have been the subject of many studies, due to their potential use as hydrogen-selective membranes for gas separation or purification [1,2]. Owing to the high cost of palladium and in order to increase the flow rate of hydrogen, composite membranes, formed by a thin layer of palladium deposited on a porous support, are largely preferred to thick self-standing metal membranes. Differe…
Evolution of microstructures and mechanical properties during dissimilar electron beam welding of titanium alloy to stainless steel via copper interl…
2013
Abstract The influence of operational parameters on the local phase composition and mechanical stability of the electron beam welds between titanium alloy and AISI 316L austenitic stainless steel with a copper foil as an intermediate layer has been studied. It was shown that two types of weld morphologies could be obtained depending on beam offset from the center line. Beam shift toward the titanium alloy side results in formation of a large amount of the brittle TiFe2 phase, which is located at the steel/melted zone interface and leads to reducing the mechanical resistance of the weld. Beam shift toward the steel side inhibits the melting of titanium alloy and, so, the formation of brittle…
Mechanical properties and corrosion behaviour of low carbon martensitic stainless steel after machining
2014
The influence of different combinations of cutting conditions on the mechanical behaviour (microhardness), the microstructure and the corrosion behaviour in NaCl solution (using the electrochemical microcell technique and pulse potentiodynamic testing) of a low carbon martensitic stainless steel (grade X4CrNiMo16.5.1 stainless steel) after tempering treatment was studied. Microhardness was increased on the machined surface. In addition, the electrochemical experiments have shown that the machined materials have a heterogeneous electrochemical behaviour. Significant effect of machining on pitting corrosion was noticed. The pitting potential was found to decrease as the microhardness increase…
Structural and Magnetic Properties of Epitaxial Ni<sub>2</sub>MnGa Thin Films
2009
We report on the preparation and investigation of epitaxial thin films of the magnetic shape memory alloy Ni2MnGa. For samples close to the stoichiometric composition we find that the phase transformation temperature is affected by the crystallographic orientation. Changes in the crystal structure due to the transformation are observed using temperature-dependent X-ray diffraction. Films with higher manganese content are in the martensitic state at room temperature. Those samples on Al2O3(11-20) reveal the 7-layered orthorhombic structure that allows strains up to 10 %. To avoid blocking of magnetostrictive effects by the substrate, free-standing films are prepared using water-soluble NaCl(…