Search results for "LOAD"
showing 10 items of 1967 documents
Analysis-oriented stress–strain model of CRFP-confined circular concrete columns with applied preload
2018
The compressive behavior of FRP-confined concrete is a current issue in the field of structural retrofitting. The available models well predict the stress–strain behavior under monotonic and cyclic loads. However, in the practical applications, columns that need an increasing of bearing capacity are often strengthened under serviceability load conditions, with a stress and strain state that could change the response of the reinforced systems with respect to the case of the unloaded state. In this paper, the compressive behavior of circular FRP-confined concrete columns with preload is analyzed with the introduction of a modified analysis-oriented model. Differently from the classical formul…
Engineering failure analysis of corroded R.C. beams in flexure and shear
2018
Abstract In the present paper, a simple model to reproduce the load-deflection response of corroded beams failing in flexure and shear is presented and discussed. Effects of diffused and pitting corrosion on steel bars, compressive concrete strength degradation and concrete bond strength degradation due to rust formation are included in the model. Engineering approach based on limit state theory was here adopted to predict the peak and the residual flexural and shear strength of corroded beams with corresponding deflections and ductility estimation. Calculation of deflection at cracking taking into account of rust formation and deflection at yielding and the ultimate state taking into accou…
Effect of the loading rate on ultimate strength of composites. Application: Pressure vessel slow burst test
2013
International audience; The strength of unidirectional elastic fibre composites is shown to depend on the loading rate as the viscoelastic nature of the matrix results in a fall in breaking load as the rate is reduced. The simulation of the accumulation of fibre breaks leading to failure, takes into account all physical phenomena involved fibre failure, including the stochastic nature of fibre strength, stress transfer through the matrix between reinforcements, interfacial debonding and the viscoelastic nature of the matrix. The kinetics of composite failure are seen to involve the initial formation of random fibre breaks which at higher loads coalesce into clusters of broken fibres. The ra…
Effect of corner over-reinforcing strips on the compressive behaviour of TRM confined masonry columns
2020
Several recent works studied the efficiency of inorganic matrix composites, namely Textile Reinforced Mortar (TRM) or Fabric Reinforced Cementitious Matrix, for enhancing the strength and shortening capacity of masonry columns subjected to axial load. Literature studies were addressed to study the great number of variables involved in the problem, such as the nature and the grade of mortar, the strength of the fabric, the number of reinforcing layers, the type, the arrangement and the strength of the masonry, and helped to draw the first technical guidelines for practitioners and designers. All the experimental works highlighted that the actual performance of TRM confinement in masonry memb…
General stress-strain model for concrete or masonry response under uniaxial cyclic compression
2002
The paper proposes analytical forms able to represent with very good approximation the constitutive law experimentally deducible by means of uniaxial cyclic compressive tests on material having softening post-peak behaviour in compression and negligible tensile strength. The envelope, unloading and reloading curves characterizing the proposed model adequately approach structural responses corresponding to different levels of nonlinearity and ductility, requiring a not very high number of parameters to be calibrated experimentally. The reliability of the model is shown by comparing the results that it is able to provide with the ones analytically deduced from two reference models (one for co…
Compressive behaviour of eccentrically loaded slender masonry columns confined by FRP
2018
Abstract Fibre Reinforced Polymer (FRP) confinement represents an effective tool for retrofitting masonry piers or columns enhancing their structural performance. This technique has been widely studied in the literature mainly with reference to short columns, while no extensive information is available on the influence of second order effects on its efficacy in case of slender members. Within this framework, the presented study concerns a simplified method able to assess the effects of FRP confinement on the compressive behaviour of slender masonry columns. A proper constitutive law of FRP confined masonry in compression is adopted for performing a sectional analysis, in which also consider…
Practical Model for Load-Carrying Capacity of Eccentrically Loaded Square Column Footings
2018
In this paper, a practical calculus model based on the strut-and-tie approach for prediction of the load-carrying capacity of eccentrically loaded RC column footings with square cross sections is presented. Existing models based on beam or slab models with flexural and two-way slab punching shear failure are presented and discussed. Several subgrade contact pressure distributions for column footings are considered. A parametric analysis of the effects of footing and column dimensions (depth, width), longitudinal ratio of longitudinal steel, and strength of concrete and steel is made for all models examined. Available experimental data are utilized to verify the model in comparison with exis…
Analytical modelling of force transmission in axially loaded RC columns with indirectly loaded jackets
2019
Abstract Concrete and steel jacketing are common strengthening techniques for reinforced concrete (RC) columns subjected to axial loads. In the most of cases the external jacket is made leaving gaps between the strengthening layer and the slabs, avoiding to carry directly a portion of the load. In this way, the external jacket induces a confinement pressure on the inner column, and its beneficial effect is due to the increase of strength and ductility. However, shear stresses develop on the interface between the column and consequently, the external jacket can be considered indirectly loaded. It sustains a portion of the axial load, which depends by the value of the axial shortening, relati…
Behaviour of concrete deep beams with openings and low shear span-to-depth ratio
2012
Abstract The goal of this study is to experimentally and analytically evaluate the influence of circular openings in reinforced concrete deep beams with low shear span-to-depth ratio. Twenty reinforced concrete small-scale deep beams with or without openings were tested in flexure under four-point loading. The beams had a small shear span-to-depth ratio in order to stress the shear behavior. The specimens had different reinforcement arrangements and opening positions. The load was transmitted to the specimen with bearing plates having the same side length as the beam. Two LVDT’s were arranged to record the transverse and axial strain of the theoretical struts forming in the beam. Additional…
Analysis of Rectangular Orthotropic Membranes for Mechanical Properties Identification through Load-Displacement Data
2021
In this paper, an innovative procedure is introduced for the identification of the mechanical properties of orthotropic membranes based on load-displacement data. To this end, novel functional forms of the displacement components for rectangular membranes are appropriately introduced. Unknown coefficients of these displacement functions are determined, minimizing the total potential energy of the membrane. The energy method is then combined with an optimization procedure to estimate the elastic constants of the membranes in a straightforward manner. Specifically, a genetic algorithm is used to minimize a properly defined objective function directly related to the sought mechanical propertie…