Search results for "Mécanique"
showing 10 items of 83 documents
Mechanical properties, internal structure and transport mechanism of oxygen in cork
2015
During the post bottling aging, premature oxidation reactions could occur and the oxygen barrier properties of the stopper are often pointed out. Nowadays, the internal structure of this material or the effect of hydration on its mechanical properties are still undetermined. Moreover, regarding the barrier properties, the limiting step of the oxygen transfer was not yet fully understood as well as the effect of compression or the role of the glass/cork interface in a bottleneck. The study of the internal structure of cork stopper allowed us to visualize the macroporosity of the material and conclude that there is no interconnectivity between lenticels, for the two qualities studied. The eff…
ST-segment elevation myocardial infarction: Management and association with prognosis during the COVID-19 pandemic in France.
2021
Systems of care have been challenged to control progression of the COVID-19 pandemic. Whether this has been associated with delayed reperfusion and worse outcomes in French patients with ST-segment elevation myocardial infarction (STEMI) is unknown.Aim: To compare the rate of STEMI admissions, treatment delays, and outcomes between the first peak of the COVID-19 pandemic in France and the equivalent period in 2019.Methods: In this nationwide French survey, data from consecutive STEMI patients from 65 centres referred for urgent revascularization between 1 March and 31 May 2020, and between 1 March and 31 May 2019, were analysed. The primary outcome was a composite of in-hospital death or no…
Conceptualisation et classification des problèmes de fatigue mécanique
2011
International audience; On propose de conceptualiser et de classifier les problèmes de calcul de structures dits de fatigue (dans le cadre de la Mécanique de lʼEndommagement). Parce que le concept de fatigue est avant tout un concept que lʼon peut estimer structural plutôt que local, cette classification est faite dʼabord sur des grandeurs structurales. Ensuite, on donne une classification faite sur des grandeurs locales. Lʼobjectif de ces classifications est de favoriser la résolution locale des problèmes de fatigue dʼune classe donnée en aidant à la justification du passage des lois dʼévolution obtenues par la Thermodynamique à celles écrites dans le cadre de la fatigue.
Impact behaviour of flax/epoxy composite plates
2015
This paper presents an experimental investigation of the impact behaviour of flax/epoxy composite plates submitted to low-velocity transverse impact. Low energy drop-weight impact tests have been performed on two types of quasi-isotropic flax/epoxy composites, rectangularly shaped with edges lengths of 142 mm × 94 mm and 2.85 mm thick. Residual properties have been assessed by compression after impact tests. A detailed description of damage development, especially the increase of the rear face crack with respect to the impact energy is given by the microscopic observation. The influence of impact damage on the residual strength is described. A loss of 15%–30% in compression resistance was n…
A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites
2012
Experimental investigations on flax and glass fabrics reinforced epoxy specimens, i.e. FFRE and GFRE, submitted to fatigue tests are presented in this paper. Samples having [0/90]3S and [±45]3S stacking sequences, with similar fibre volume fractions have been tested under tension–tension fatigue loading. The specific stress-number of cycles to failure (S–N) curves, show that for the [0/90]3S specimens, FFRE have lower fatigue endurance than GFRE, but the [±45]3S FFRE specimens offer better specific fatigue endurance than similar GFRE, in the studied life range (<2 × 10^6). Overall, the three-stage stiffness degradation is observed in all cases except for [0/90]3S FFRE specimens, which prese…
Generation and characterization of T40/A5754 interfaces with lasers
2014
Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…
Effect of relative humidity on carvacrol release and permeation properties of chitosan based films and coating
2014
International audience; The influence of water vapour conditions on mass transport and barrier properties of chitosan based films and coatings were studied in relation to surface and structural properties. Water contact angles, material swelling, polymer degradation temperature, barrier properties (PO2, PCO2, WVP) and aroma diffusion coefficients were determined. The solvent nature and the presence of carvacrol influenced the surface and structural properties and then the barrier performance of activated chitosan films. Increasing RH from 0% to 100% led to a significant increase in material swelling. The plasticization effect of water was more pronounced at high humid environment, while at …
Additive manufacturing Processing and characterization of Fe-Si soft magnetic alloys
2021
Iron silicon (Fe-Si) alloys, also named silicon steels, are the most widely used owing to their excellent soft magnetic properties and economic costs. As electronic devices become diversified and automated, it is urgent to develop high-performance soft magnetic alloys with good reliability. For functional soft magnetic alloys, the SLM technique shown the potential to manufacture soft magnetic components directly from raw materials, such as the rotor and stator of the motor. In order to explore and develop new routes for manufacturing Fe-Si alloys, the investigation into the microstructures and properties of SLMed Fe-Si alloys from pre-alloyed powders was presented in this work. The most imp…
Language and Mind : towards a linguistic and critical study of spectacular language.
2021
He thesis focuses on a sample of written messages drawn from the daily environment. In the general framework of the relationship between language and power, the thesis consists in the analysis of written messages broadcast in daily life. The research is based on the collection of messages found on various media, including advertising displays. The thesis begins with the reception and use of the notions of newspeak and wooden tongue in their historical and contemporary context in order to show the topicality of linguistic and sociological questions about the relationship between language and power. The study of these two notions, through the linguistic and epistemological issues they involve…
Morphological characterisation of soil structure in tilled fields: from a diagnosis method to the modelling of structural changes over time
2004
Characterisation of soit structure within the tilled layer of cultivated fields is crucial because the importance of this soil characteristic on the biological, chemical and physical properties of the soil and its repercussions on water cycle, root growth and functioning. We present in this paper a method for field characterisation of soil structure. This method, practised since the 1970s, was designed for field diagnosis of the effects of cropping systems on soil structure. It is based on a stratification of the observation face of a pit dug perpendicular to the direction of tillage and traffic: spatial compartments are distinguished, according to the nature of the mechanical stresses they…