Search results for "MATERIA"
showing 10 items of 33501 documents
Fast pyrolysis of hot-water-extracted and delignified silver birch (Betula pendula) sawdust by Py-GC/MS
2017
The thermochemical behavior of birch (Betula pendula) sawdust both untreated and after various chemical treatments (hot-water extraction, delignification, and hot-water extraction followed by delignification) was investigated by pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS). In each case, major GC-amenable condensable products were classified into several compound groups, and the formation of these monomer-related fragments from feedstock samples with varying mass portions of the structural constituents (cellulose, hemicelluloses, and lignin) were determined at 500 °C and 700 °C at hold times of 5 s and 20 s. The formation of pyrolysis products was shown to be characteristically…
Study about Mechanical Properties of Materials Obtained by Thermoforming
2019
Plastic materials have played a very important role in the development of our modern civilization. It can be said that plastic materials are a tribute to man’s creativity and inventiveness. Plastic materials are the key to the innovation of many products and technologies in various sectors such as electrical and electronic equipment, packaging, civil engineering, agriculture, power generation, medical and pharmaceutical industry, aerospace and not last automotive industry. An increasingly important aspect in the automotive industry, in terms of fuel consumption is the lower weight of the components, while maintaining a very high stiffness. The difficulties of the design process of thermofor…
Regarding the influence of the particle size of crumb rubber from waste rubber on the physical and mechanical characteristics of reclaimed rubber
2017
Thus, at present, a large amount of rubber waste cannot be higher harnessed due to recovery technologies used. Also, the requirements for new products of rubber worldwide are greater than the production capacity and the availability of raw materials. To offset this balance is necessary to improve technologies for recycling waste rubber so to can get regenerated rubber with the best mechanical physical characteristics. The main technology for obtaining the regenerated rubber is based on the rubber waste shredding and making the powder, so that it can be carried out de-vulcanization in autoclave. All the time it was monitored as the de-vulcanization process to be as economical and less pollut…
Definition of the thermographic regions of interest in cycling by using a factor analysis
2016
Abstract Research in exercise physiology using infrared thermography has increased in the last years. However, the definition of the Regions of Interest (ROIs) varies strongly between studies. Therefore, the aim of this study was to use a factor analysis approach to define highly correlated groups of thermographic ROIs during a cycling test. Factor analyses were performed based on the moment of measurement and on the variation of skin temperatures as a result of the cycling exercise. 19 male participants cycled during 45 min at 50% of their individual peak power output with a cadence of 90 rpm. Infrared thermography was used to measure skin temperatures in sixteen ROIs of the trunk and lowe…
Study Regarding the Optimal Milling Parameters for Finishing 3D Printed Parts from ABS and PLA Materials
2018
Abstract In this paper we proposed to identify the optimum milling parameter required for finishing processes performed on 3Dprinted parts from ABS and PLA materials. We have identified the optimum milling parameters for a constant spindle speed of 3500 rot/min for face milling and profile contouring operations with different tools diameters. The study was performed on 3D printed specimens from ABS and PLA materials.
Enhancing the sound absorption of small-scale 3D printed acoustic metamaterials based on Helmholtz resonators
2018
Acoustic metamaterials have recently become of interest for their ability to attenuate sound by breaking the mass-density law. In this paper, acoustic metamaterials based on Helmholtz resonators and capable of attenuating sound up to 30 dB are fabricated for sound absorption applications in the small scale. The proposed metamaterials are subwavelength at a factor of $\lambda /12$ with respect to the lateral dimension of the units. The directional response due to the position of the acoustic source on the sound attenuation provided by the metamaterial is investigated by controlling the location of a loudspeaker with a robot arm. To enhance and broaden the absorption bands, structural modific…
Adaptive Feedforward Control of a Pressure Compensated Differential Cylinder
2020
This paper presents the design, simulation and experimental verification of adaptive feedforward motion control for a hydraulic differential cylinder. The proposed solution is implemented on a hydraulic loader crane. Based on common adaptation methods, a typical electro-hydraulic motion control system has been extended with a novel adaptive feedforward controller that has two separate feedforward states, i.e, one for each direction of motion. Simulations show convergence of the feedforward states, as well as 23% reduction in root mean square (RMS) cylinder position error compared to a fixed gain feedforward controller. The experiments show an even more pronounced advantage of the proposed c…
Mechanical and metallurgical characterization of AA6082-T6 sheet-bulk joints produced through a linear friction welding based approach
2020
In the last decades, new flexible manufacturing processes have been developed to face the demands, by many industrial fields, for highly customized complex functional parts. The peculiar design of these components often overcomes conventional sheet metal and bulk metal forming processes capabilities. In order to face this issue, new hybrid techniques, capable of exploit key advantages of different processes, have to be developed. In this study, a method to obtain sheet-bulk joints, based on the Linear Friction Welding process, is proposed. The feasibility of the technique was investigated through an experimental campaign carried out with varying pressure and oscillation frequency using AA60…
Analysis of Electrical Energy Demands in Friction Stir Welding of Aluminum Alloys
2017
Abstract Manufacturing processes, as used for discrete part manufacturing, are responsible for a substantial part of the environmental impact of products. Despite that, most of metalworking processes are still poorly documented in terms of environmental footprint. To be more specific, the scientific research has well covered conventional machining processes, concerning the other processes there is a lack of knowledge in terms of environmental load characterization instead. The present paper aims to contribute to fill this knowledge gap and an energetic analysis of Friction Stir welding (FSW) is presented. Following the CO2PE! methodological approach, power studies and a preliminary time stu…
Analysis of hybrid vehicle transmissions with any number of modes and planetary gearing: kinematics, power flows, mechanical power losses
2021
Abstract This paper is focused on upgrading a unified parametric model, available in the literature, that can perform both the analysis and the design of Power-Split Continuously Variable Transmissions (PS-CVTs), which are particularly promising to deploy in the hybrid electric powertrain. In particular, this work is focused on the analysis of PS-CVTs and proposes a new matrix approach for identifying the basic functional parameters underlying the model from the constructive layout of the transmission. This new method does not rely on a case-specific formulation, thus befits any power-split transmission, regardless of the number of planetary and ordinary gear sets and their constructive arr…