Search results for "MATERIA"
showing 10 items of 33501 documents
On the complete interface development of Al/Cu magnetic pulse welding via experimental characterizations and multiphysics numerical simulations
2021
Abstract A complex Al/Cu magnetic pulse welding interface is systematically investigated using experimental characterizations and numerical simulations. A Coupled electromagnetic-mechanical simulation is proposed to compute the impact velocity and impact angle along the entire interface. This model allows to further understand the formation mechanism of various interface characteristics during MPW. The results revealed that the impact velocity gradually decreases in conjunction with the gradual increase of the impact angle. These simulations elucidate the experimentally observed successive interface morphologies, i.e., the unwelded zone, vortex zone, intermediate (IM) layers and wavy interf…
Design of a telescopic tower for wind energy production with reduced environmental impact
2019
A prototype of a telescopic pole for wind energy production with low environmental impact and its lifting system for a 60 to 250 kW turbine and a height of 30 m have been designed and manufactured. A telescopic tower, which is raised and lowered by automation or by remote control, allows to differentiate the presence of the generator within the landscape over time. The technology currently available for lifting and lowering wind turbines is made up of telescopic poles of heights of less than 10 meters and with tilting posts of height below 30 m. Without a state of the art to refer to, the telescopic pole and its lifting system have been designed starting from scratch and solving with innova…
Friction Model for Tool/Work Material Contact Applied to Surface Integrity Prediction in Orthogonal Cutting Simulation
2017
Abstract Tribological behavior at both tool/chip and tool/work material interfaces should be highly considered while simulating the machining process. In fact, it is no longer accurate to suppose one independent constant friction coefficient at the tool/chip interface, since in reality it depends on the applied contact conditions, including the sliding velocity and pressure. The contact conditions at both above mentioned interfaces may affect the thermal and mechanical phenomena and consequently the surface integrity predictions. In this article, the influence of contact conditions (sliding velocity) on the tribological behavior of uncoated tungsten carbide tool against OFHC copper work mat…
Aluminium sheet metal scrap recycling through friction consolidation
2019
Abstract In the last decades, several direct-recycling techniques have been developed and investigated in order to avoid material remelting, typical of the conventional aluminum alloys recycling processes. Moreover, the remelting step for aluminum recycling is affected by permanent material losses. Solid-state recycling processes have proven to be a suitable strategy to face such issues. Friction Consolidation is an innovative solid state-recycling technology developed for metal chips. During the process, a rotating die is plunged into a hollow chamber containing the material to be processed. The work of friction forces decaying into heat soften the material and, together with the stirring …
DESDEO: The Modular and Open Source Framework for Interactive Multiobjective Optimization
2021
Interactive multiobjective optimization methods incorporate preferences from a human decision maker in the optimization process iteratively. This allows the decision maker to focus on a subset of solutions, learn about the underlying trade-offs among the conflicting objective functions in the problem and adjust preferences during the solution process. Incorporating preference information allows computing only solutions that are interesting to the decision maker, decreasing computation time significantly. Thus, interactive methods have many strengths making them viable for various applications. However, there is a lack of existing software frameworks to apply and experiment with interactive …
Performance and feasibility of biotrickling filtration in the control of styrene industrial air emissions
2017
Abstract The performance and feasibility of a pilot unit of biotrickling filter (BTF) for the treatment of industrial emissions polluted by styrene was investigated for one year at a fiber reinforced plastic industrial site. The pilot unit was packed with a structured material with a volume of 0.6 m3. Monitoring results have shown successful treatment of the industrial styrene emissions working at empty bed residence times (EBRT) between 31 and 66 s. The best performance was obtained after 300 days when a more stable biofilm had been developed, obtaining the highest elimination capacity of 18.8 g m−3 h−1 (removal efficiency of 75.6%) working at 31 s of EBRT. In addition, a photocatalytic re…
Transformation of Construction Cement to a Self-Healing Hybrid Binder
2019
A new biomimetic strategy to im prove the self-healing properties of Portland cement is presented that is based on the application of the biogenic inorganic polymer polyphosphate (polyP), which is used as a cement admixture. The data show that synthetic linear polyp, with an average chain length of 40, as well as natural long-chain polyP isolated from soil bacteria, has the ability to support self-healing of this construction material. Furthermore, polyP, used as a water-soluble Na-salt, is subject to Na+/Ca2+ exchange by the Ca2+ from the cement, resulting in the formation of a water-rich coacervate when added to the cement surface, especially to the surface of bacteria-containing cement/c…
Unexplored alternative use of calcareous sludge from the paper-pulp industry in green geopolymer construction materials
2020
Abstract Calcareous sludge is an alkaline waste produced by the paper pulp industry that is commonly disposed of in land-fill. However, recent studies and the European regulations discourage such practice. This work investigates an alternative and innovative way to recycle and reuse this waste, as filler, in the production of green geopolymeric mortars intended for applications in construction. This is the first time that this calcareous sludge is used to produce novel waste-based materials, in both construction and geopolymer technology. The novel alkali-activated mortar also uses biomass fly ash – another slightly investigated waste stream – to substitute the metakaolin (70 wt% substituti…
Onset of cohesion in cement paste
2004
It is generally agreed that the cohesion of cement paste occurs through the formation of a network of nanoparticles of a calcium-silicate-hydrate ("C-S-H"). However, the mechanism by which these particles develop this cohesion has not been established. Here we propose a dielectric continuum model which includes all ionic interactions within a dispersion of C-S-H particles. It takes into account all co-ions and counterions explicitly (with pure Coulomb interactions between ions and between ions and the surfaces) and makes no further assumptions concerning their hydration or their interactions with the surface sites. At high surface charge densities, the model shows that the surface charge of…
The open metastable structure of a collapsible sand: fabric and bonding
2015
This paper deals with the compositional and textural characteristics determining open metastable structures in the pleistocenic sand outcropping in the Agrigento district (Sicily). The aim of the study was to individuate the bonding types occurring between grains that could generate matric suction phenomena. The composition and microfabric were characterised by means of granulometry, porosimetry, permeability, optical and ESEM-EDS microscopy, thermogravimetry and XR diffractometry, electric conductivity, and ionic chromatography. The data thus acquired show that the skeleton of the sand is constituted mostly by bioclasts and microfossils, calcite and quartz monocrystalline grains. Moreover,…