Search results for "MICI"

Mass transfer in channels in the presence of wall transpiration

Mass transfer to or from transpiring walls is studied. Examples from different fields of engineering, notably involving membrane processes, are illustrated, and analogies or differences with respect to heat transfer problems are discussed. With special reference to plane channel flow, suitable dimensionless parameters are introduced, and the dependence of the Sherwood number upon these parameters is computed by a number of approaches of different complexity, from two-dimensional CFD to simple algebraic correlations.

CFD prediction of flow, heat and mass transfer in woven spacer-filled channels for membrane processes

2021

Abstract Flow and heat or mass transfer in channels provided with woven spacers made up of mutually orthogonal filaments were studied by Computational Fluid Dynamics. The problem addressed was the combined effect of the parameters that characterize the process: pitch to height ratio P/H (2, 3 and 4), flow attack angle θ (0, 7, 15, 20, 30, 40 and 45°) and Reynolds number Re (from ~1 to ~4000). The Prandtl number was 4.33, representative of water at ~40°C, while the Schmidt number was 600, representative of NaCl solutions. Simulations were performed by the finite volume code Ansys CFX™ 18.1 using very fine grids of ~6 to ~14 million volumes. For Re > ~400, the SST turbulence model was used to…

Ionic shortcut currents via manifolds in reverse electrodialysis stacks

2020

Abstract Reverse electrodialysis (RED) is a blue energy technology for clean and sustainable electricity harvesting from the mixing entropy of salinity gradients. Recently, many efforts have been devoted to improving the performance of RED units by developing new ion-exchange membranes and by reducing the detrimental phenomena affecting the process. Among these sources of “irreversibility”, the shortcut currents (or parasitic currents) flowing through alternative pathways may affect the process efficiency. Although such phenomena occur in several electrochemical processes (e.g. fuel cells, bipolar plate cells and vanadium redox flow batteries), they have received a poor attention in RED uni…

A 2-D model of electrodialysis stacks including the effects of membrane deformation

2021

Abstract Membrane-based processes have gained a relevant role in many engineering applications. Much effort has been devoted to thoroughly understand the fundamental phenomena behind them. However, membrane deformation has been taken into consideration only recently, although much evidence has shown its impacts in many applications. This work presents a novel 2-D, multi-scale, semi-empirical process model able to predict the behavior and the performance of Electrodialysis (ED) systems in cross-flow configurations in the presence and absence of local membrane deformations. The model exploits the results and the simulation approaches of previous fluid-structure investigations performed by the…

Vibration-based identification of mechanical properties of orthotropic arbitrarily shaped plates: Numerical and experimental assessment

2018

Abstract An innovative procedure is introduced for the identification of the mechanical parameters of orthotropic plates of arbitrary shape, under various boundary conditions, based on vibration data. The method employs a combination of a convenient Rayleigh-Ritz approach and Particle-Swarm Optimization to estimate elastic constants of the orthotropic material in a straightforward manner, without requiring computationally demanding iterative Finite Element analyses. Specifically, the pb-2 Rayleigh-Ritz procedure is extended and applied to deal with orthotropic plates, simplifying the approach to more easily treat generic plate shapes, taking advantage of the Green's theorem. The method is t…

CFD Investigation of Spacer-Filled Channels for Membrane Distillation

2019

The membrane distillation (MD) process for water desalination is affected by temperature polarization, which reduces the driving force and the efficiency of the process. To counteract this phenomenon, spacer-filled channels are used, which enhance mixing and heat transfer but also cause higher pressure drops. Therefore, in the design of MD modules, the choice of the spacer is crucial for process efficiency. In the present work, different overlapped spacers are investigated by computational fluid dynamics (CFD) and results are compared with experiments carried out with thermochromic liquid crystals (TLC). Results are reported for different flow attack angles and for Reynolds numbers (Re) ran…

Pressure drop at low reynolds numbers in woven-spacer-filled channels for membrane processes: CFD prediction and experimental validation

2017

The energy consumption due to pumping power is a crucial issue in membrane processes. Spacers provide mechanical stability and promote mixing, yet increasing pressure drop. Woven spacers and their behaviour at low Reynolds numbers are less studied in the literature. Nevertheless, they are typical of some membrane technologies, as reverse electrodialysis (RED). RED is a promising technology for electric power generation by the chemical potential difference of two salt solutions within a stack equipped by selective ion-exchange membranes. The mechanical energy required for pumping the feed solutions, can dramatically reduce the net power output. In this work computational fluid dynamics (CFD)…

Experimental and computational investigation of heat transfer in channels filled by woven spacers

2017

Abstract Models of woven-type spacer-filled channels were investigated by Computational Fluid Dynamics (CFD) and parallel experiments in order to characterize the performance of Membrane Distillation (MD) modules. The case of overlapped spacers was analysed in a companion paper. Experiments were based on a non-intrusive technique using Thermochromic Liquid Crystals (TLC) and digital image processing, and provided the distribution of the local convective heat transfer coefficient on a thermally active wall. CFD simulations ranged from steady-state conditions to unsteady and early turbulent flow, covering a Reynolds number interval of great practical interest in real MD applications. A specif…

Investigation of heat transfer in spacer-filled channels by experiments and direct numerical simulations

2016

Abstract The analysis of flow fields and heat or mass transfer phenomena is of great importance in the optimum design of spacer-filled channel geometries for a variety of membrane-based processes. In the present work, models of spacer-filled channels often adopted in Membrane Distillation are simultaneously investigated by experiments and Computational Fluid Dynamics (CFD). Experiments rely on a non-intrusive technique, based on the use of Thermochromic Liquid Crystals (TLC) and digital image processing, and provide the local distribution of the convective heat transfer coefficient on a thermally active wall. CFD relies on steady-state (laminar flow) simulations in the lower end of the Reyn…

Performance comparison between overlapped and woven spacers for membrane distillation

2017

The sustainable production of freshwater from seawater desalination is receiving increasing attention. Recently, some desalination technologies are taking advantage from the coupling with renewable resources; among them, membrane distillation (MD) is one of the most promising since it can be easily powered by low-grade thermal energy. MD being an emerging technology, efforts are required to optimize geometry and operating conditions of real units in order to reduce the unitary freshwater production cost. In particular, temperature polarization is a well-known detrimental effect for the process driving force; spacers are traditionally used to enhance mixing and make temperature boundary laye…