Search results for "MOLA"
showing 10 items of 1216 documents
Consequences of linking charged and uncharged monomers to binary copolymers studied in dilute solution. Part I: Viscometric behavior of the homopolym…
2017
Abstract Intrinsic viscosities, generalized intrinsic viscosities and viscometric interaction parameters were measured for aqueous solutions of poly(ethylene oxide) [PEO], poly(N,N-dimethyl aminoethyl methacrylate) [PR] (uncharged) and for poly{[2-(methacryloyloxy)ethyl] trimethylammonium iodide} [PR+] (charged) within a wide range of molar masses. In this manner it was possible to establish the information required for the study of non-additivity effects upon the formation of binary copolymers from the monomers specified above. The following additional items were of particular interest: The effects of charging PR to PR+ and the composition dependence of the coil overlap in the case of sali…
Intrinsic Viscosities of Polymer Blends: Sensitive Probes of Specific Interactions between the Counterions of Polyelectrolytes and Uncharged Macromol…
2018
In joint dilute aqueous solutions of pullulan (PUL) and poly(sodium 4-styrenesulfonate) (PSS-Na) the Na+ ions of the polyelectrolyte interact so favorably with the monomeric units of PUL that isolated coils containing both types of macromolecules are formed upon dilution. When water is replaced against a 1 M solution of NaCl, this effect dies out because of the large surplus of Na+ ions. On the other hand, if the water contains increasing amounts of the respective counterpolymer instead of NaCl, the formation of mixed isolated coils is fostered, where a further diminution of the intrinsic viscosities is caused by the lower the solvent quality. The molar mass of PSS-Na plays an important rol…
The fractal calibration method applied to the characterization of polymers in solvent mixtures and in mixed gel packings by SEC.
2007
The size-exclusion chromatographic (SEC) behaviour of different solvent/polymer systems in three packing sets has been analysed from fractal considerations. The three-column sets studied are specifically formed by: (i) 'pure' micro-styragel, (ii) 'mixed' TSK Gel H(HR + XL + HR) and (iii) mixed TSK Gel H(XL + HR + XL). The experimental data reveals that in most of the systems assayed the classical universal calibration (UC) is not fulfilled, denoting the existence of secondary effects accompanying the main SEC mechanism. In order to obtain an accurate characterization of different polymers eluted in solvent mixtures and/or mixed packings, the use of a reliable and trusted calibration curve i…
Combined Effects of Pressure and Shear on the Phase Separation of Polymer Solutions
1998
Experimental information available in the literature on the phase separation behavior of the system trans-decalin/polystyrene as a function of pressure and shear rate for different molar masses M o...
Normal-phase (temperature gradient) interaction chromatography – A powerful tool for the characterisation of high molecular weight chain-end function…
2015
Abstract We report here, for the first time, quantitative analysis of end-group functionalisation and the extent of end-group modification of polymers with molar mass up to 200,000 g mol −1 , using a combination of isothermal and temperature gradient interaction chromatography. At such high molecular weights, other common analytical techniques such as MALDI-ToF-MS and NMR spectroscopy are simply unable to offer any quantitative insight into the end-group functionality of polymers. Thus, normal phase isothermal interaction chromatography (NP-IIC) has been used to characterise a series of polystyrene samples, with identical molar mass (c. 90,000 g mol −1 ), each carrying a single chain-end fu…
Chain Stiffness of Elastin-Like Polypeptides
2010
The hydrodynamic radii of a series of genetically engineered monodisperse elastin like polypeptides (ELP) was determined by dynamic light scattering in aqueous solution as function of molar mass. Utilizing the known theoretical expression for the hydrodynamic radius of wormlike chains, the Kuhn statistical segment length was determined to be lk = 2.1 nm, assuming that the length of the peptide repeat unit was b = 0.365 nm, a value derived for a coiled conformation of ELP. The resulting chain stiffness is significantly larger than previously reported by force-distance curve analysis (lk < 0.4 nm). The possible occurrence of superstructures, such as hairpins or helices, would reduce the conto…
The uptake of N-(2-hydroxypropyl)-methacrylamide based homo, random and block copolymers by human multi-drug resistant breast adenocarcinoma cells
2009
A series of well-defined, fluorescently labelled homopolymers, random and block copolymers based on N-(2-hydroxypropyl)-methacrylamide were prepared by reversible addition–fragmentation chain transfer polymerization (RAFT polymerization). The polydispersity indexes for all polymers were in the range of 1.2–1.3 and the number average of the molar mass (Mn) for each polymer was set to be in the range of 15–30 kDa. The cellular uptake of these polymers was investigated in the human multi-drug resistant breast adenocarcinoma cell line MCF7/ADR. The uptake greatly depended on the polymer molecular mass and structure. Specifically, smaller polymers (approx. 15 kDa) were taken up by the cells at m…
Dimesogenic liquid crystalline oligosiloxanes
1995
Abstract In this paper, the syntheses, phase properties and ferroelectric properties of new liquid crystalline oligosiloxane dimesogens are described. Smectic phases are dominant in this class of materials. Spontaneous polarizations are in the range of 10 to approximately 100 nCcm−2. The materials show interesting properties for display applications. Although offering higher mechanical stability than low molar mass materials, their switching is significantly faster (switching times in the range of some 10−5s) than is the case for similar side group polymers (typically some 10−3s). Therefore these new oligosiloxane derivatives may be ideal for building flexible displays. In addition, mixture…
Formation of micro- and nano-spheric particles (filter dust) during the preparation of cellulose acetate membranes
2003
Abstract Membranes were prepared from six samples of cellulose acetate (CA) differing in their average molecular weight (75–260 kg/mole) and molecular weight distribution using methyl acetate as solvent and 2-propanole as precipitant. The routes through the phase diagram and the evaporation times were varied in these experiments. Electron microscopy demonstrates that the amount of filter dust (CA particles deposited on the membrane surface) decreases as the fraction of low molecular weight material in the starting polymer becomes less. For low average molar mass of CA and moderate polymer concentrations in the casting solution the dust consists of individual spheres of relatively uniform si…
Morphology and Rheology of HDPE/LCP Blends Compatibilized by a Novel PE-g-LCP Copolymer
1999
A novel graft copolymer (PE-g-LCP) consisting of polyethylene (PE) backbones and liquid crystalline polymer (LCP) branches was synthesized via reactive blending of an acrylic acid-functionalized PE (Escor 5000 by Exxon) with a semiflexible LCP (SBH 1 : 1 : 2 by Eniricerche S.p.A.). The crude reactive blending product (COP) was shown by investigation of the fractions soluble in boiling toluene and xylene and of the residue to contain unreacted Escor and SBH, together with the graft copolymer forming the interphase. The compatibilizing activity of COP for PE/SBH blends, compared to that of pure Escor, was investigated using two PE grades. The COP addition into 80/20 PE/SBH blends caused a muc…