Search results for "MSM"

Determination of dynamic properties of flax fibres reinforced laminate using vibration measurements

2017

International audience; Experimental and numerical methods to identify the linear viscoelastic properties of flax fibre reinforced polymer (FFRP) composite are presented in this study. The method relies on the evolution of storage modulus and loss factor as observed through the frequency response. Free-free symmetrically guided beams were excited in the dynamic range of 10 Hz to 4 kHz with a swept sine excitation focused around their first modes. A fractional derivative Zener model has been identified to predict the complex moduli. A modified ply constitutive law has been then implemented in a classical laminates theory calculation (CLT) routine. Overall, the Zener model fitted the experime…

Mechanical characterization of bio-based composite/metal laminates for an application in street furniture

2019

In this work, it is proposed to study the influence of three manufacturing parameters in the development of bio-basedcomposite/steel hybrids. These parameters arethe methodof assembly between composite and metal, the distribution of composite and steellayers throughthe thicknessof the hybrid,and the stacking sequence of the composite part of the hybrid. The study was conducted through impact tests at different energies and quasi-static three-point bending tests. For each of these parameters, the influenceon the mechanical properties of the hybrid is evaluated.The results show that these properties depend essentially on the relative distribution of steel and composite through the thickness.

Maximum Torque per Ampere Control strategy for low-saliency ratio IPMSMs

2019

This paper deals with electrical drives employing low-saliency ratio interior permanent magnet synchronous motors. In particular, in order to help the designers choosing the best control algorithm, the performances of the Maximum Torque Per Ampere Control (MTPA) and the Field Orientation Control (FOC) are here both theoretically and experimentally assessed and compared, by using, as performance indicators, the torque-current ratio and the power losses. The tests are carried out on a low-power motor for various speeds and loads by implementing the two control strategies in a dSPACE® rapid prototyping system. The results show that the Maximum Torque Per Ampere algorithm has some appreciable a…

Sexually transmitted infections among men who have sex with men living in Western Sicily (south Italy)

2011

Improvement of IPMSM performance through a mixed radial-tangential rotor structure

2010

In this paper an IPMSM (Interior Permanent Magnet Synchronous Motor) rotor configuration optimization is proposed in order to increase the performances in terms of torque, limiting at the same time the rotor leakage flux. The final mixed radial and tangential rotor configuration here proposed and described determines a reduction in PM material quantity of about 25% compared to a tangential IPMSM one with the same dimension and weight, together with an increase of the motoring torque of about 50%. Some simulation carried out by using a FEM software and a comparative analysis with two traditional IPMSMs rotor configurations show that a significant improvement can be achieved with limited chan…

Analysis, characterization and minimization of IPMSMs cogging torque with different rotor structures

2015

This paper presents the analysis, characterization and comparison of the cogging torque components generated by five different IPMSM rotor structures. More in detail, an IPMSM model (named IPMSM1), which is derived from a commercial geometry, is analyzed by using a Finite Element Method (FEM) approach. Then, four other IPMSM models, which are obtained by modifying the IPMSM1 rotor structure and by maintaining the same stator configuration, are proposed and analyzed. From the obtained simulation results, the cogging torque components for each structure are determined and compared. From this comparison, a significant cogging torque decrease is occurring for the modified geometries, without af…

Microstructure-oxidation resistance relationship in Ti3AlC2 MAX phase

2020

International audience; Spark Plasma Sintering and Hot Isostatic Pressing were used to synthesize coarse-grained and fine-grained Ti3AlC2 specimens. Moreover, Spark Plasma Sintering processing parameters were modified in order to vary the TiC, Al2O3 and TixAly impurity and the porosity contents in the fine-grained samples. The influence of the Ti3AlC2 microstructure on the oxidation resistance was assesed. It is demonstrated that the grain size can drastically modify the oxidation resistance. The higher density of grain boundaries, in fine-grained specimens, increases the number of Al diffusion paths and leads to the formation of a protective alumina scale. In coarse-grained sample, Al diff…

Tensile behaviour of patch-repaired CFRP laminates

2011

The present study examines the tensile behaviour of composite structures repaired by bonding external patches. Various patches of different stacking sequences placed on both sides of the parent plate were considered. Damage development and the failure process of the repaired plates were analyzed and a parent plate fracture model has been proposed. Optimised patch repairs were calculated by finite element modelling. It was found that high stress concentration along the longitudinal edges of circular patches and/or at the transverse edges of the hole leads to early damage initiation in the parent plate. However, the position of damage initiation and the process of damage progression depend pa…

Two multilayered plate models with transverse shear warping functions issued from three dimensional elasticity equations

2014

Abstract A multilayered plate theory which uses transverse shear warping functions is presented. Two methods to obtain the transverse shear warping functions from three-dimensional elasticity equations are proposed. The warping functions are issued from the variations of transverse shear stresses computed at specific points of a simply supported plate. The first method considers an exact 3D solution of the problem. The second method uses the solution provided by the model itself: the transverse shear stresses are computed integrating equilibrium equations. Hence, an iterative process is applied, the model is updated with the new warping functions, and so on. Once the sets of warping functio…

Monkeypox virus infection and creatine phosphokinase increase: A case from Italy.

2022

No abstract available.