Search results for "Marten"
showing 10 items of 28 documents
Multi-experimental study of micro-structural and mechanical consequences of thermal cycles applied to a martensitic stainless steel « APX4 »
2010
The Direction des Applications Militaires at the Commissariat à l’Énergie Atomique, a French government-funded technological research organisation, selected a low carbon chromium rich martensitic stainless steel (APX4) to manufacture components with high yield strength and ultimate tensile strength. As such, this thesis is developed around three main axes. Firstly, the thesis summarizes the existing bibliography on this steel as well as its neighboring nuances. Secondly, it engages in a precise characterization of the material that is currently used for industrial manufacturing. Finally, this highly experimental work undertakes to observe and interpret the micro-structural and mechanical co…
Microstructural Characterization of Thermo-Mechanical Treated TRIP Steels
2007
The increasing demand for the reduction of automobiles CO2 emissions for environmental preservation leads the automotive industries towards the mechanical components weight reduction. Sheet steels with multiphase microstructures exhibit favourable combinations of strength and ductility. The so called TRIP steels have a metastable microstructure that consists of a continuous ferrite matrix containing a dispersion of hard second phases martensite and bainite. These steels also contain retained austenite, at room temperature, that represents the source of the TRansformation Induced Plasticity effect. When the material is subjected to deformation step, the retained austenite transforms itself i…
A corrosion study of austenitic and martensitic steels under boiler conditions by means of 57Fe conversion electron mössbauer spectroscopy
1978
Abstract The growth of protective oxide layers on a martensitic FeCr (1.4122) and two austenitic FeCrNi steel samples (1.4550 and Incoloy 800) was studied by means of the 57Fe Conversion Electron Mossbauer Spectroscopy (CEMS). Scanning electron microscopy was applied to characterize the topographical nature of the oxide layers. Following a technical procedure of running-in steam generators, the steel specimens were oxidized in oxygen-free water at 295°C, 142 bar and a pH value between 9 and 10 for periods up to 70 h. In the case of the steels 1.4122 and 1.4550 the only oxide phase detected was non-stoichiometric magnetite, whereas nickel ferrite of nonstoichiometric composition was found…
Wavelets Image Analysis for Friction Stir Processed TiNi Functional Behavior Characterization
2015
Abstract A key topic regarding Ti Ni Shape Memory materials concerns the possibility to attain welded junctions that preserves the shape memory properties of material. Other research topic for SMAs regards the retention of the shape memory effect cyclic stability; in fact, good shape memory properties frequently decrease during SME cycling of material. A method able to improve the cyclic stability of TiNi shape memory effect is the grain refinement. Considering these above mentioned research topics, a solid state welding process, as the Friction Stir Welding, is thus attractive for SMA joining and it exhibits potentials for achieving welded joints affected by microstructural changes that pr…
Numerical modelling of fatigue crack initiation of martensitic steel
2010
Numerical simulation of micro-crack initiation that is based on Tanaka-Mura micro-crack nucleation model is presented. Three improvements were added to this model. Firstly, multiple slip bands where micro-cracks may occur are used in each grain. Second improvement deals with micro-crack coalescence by extending existing micro-cracks along grain boundaries and connecting them into a macro-crack. The third improvement handles segmented micro-crack generation, where a micro-crack is not nucleated in one step like in Tanaka-Mura model, but is instead generated in multiple steps. Numerical simulation of crack-initiation was performed with ABAQUS, using a plug-in that was written specially for ha…
Numerical modelling of fatigue crack initiation and growth of martensitic steels
2010
This paper presents a numerical simulation of micro-crack initiation that is based on Tanaka-Mura micro-crack nucleation model. Three improvements were added to this model. First, multiple slip bands where micro-cracks may occur are used in each grain. Second improvement deals with micro-crack coalescence by extending existing micro-cracks along grain boundaries and connecting them into a macro-crack. The third improvement handles segmented micro-crack generation, where a micro-crack is not nucleated in one step like in Tanaka-Mura model, but is instead generated in multiple steps. High cycle fatigue testing was also performed and showed reasonably good correlation of proposed model to expe…
Temperature-induced martensite in magnetic shape memory Fe2MnGa observed by photoemission electron microscopy
2012
The magnetic domain structure in single crystals of a Heusler shape memory compound near the composition Fe2MnGa was observed during phase transition by photoelectron emission microscopy at Beamline 11.0.1.1 of the Advanced Light Source. The behavior is comparable with recent observations of an adaptive martensite phase in prototype Ni2MnGa, although the pinning in the recent work is an epitaxial interface and in this work the effective pinning plane is a boundary between martensitic variants that transform in a self-accommodating way from the single crystal austenite phase present at high temperatures. Temperature dependent observations of the twinning structure give information as to the …
Load-deflection characteristics of superelastic and thermal nickel-titanium wires
2011
SUMMARY The aim of this study was to investigate the mechanical properties of superelastic and thermal nickel–titanium (NiTi) archwires for correct selection of orthodontic wires. Seven different NiTi wires of two different sizes (0.014 and 0.016 inches), commonly used during the alignment phase, were tested. A three-point bending test was carried out to evaluate the load–deflection characteristics. The archwires were subjected to bending at a constant temperature of 37°C and deflections of 2 and 4 mm. Analysis of variance showed that thermal NiTi wires exerted significantly lower working forces than superelastic wires of the same size in all experimental tests (P < 0.05). Wire size had a s…
Update of the distribution and habitat use of the wildcat, pine marten and weasel in Sicily
2020
The wildcat (Felis silvestris), the pine marten (Martes martes) and the weasel (Mustela nivalis) are key members of the mammalian community in Sicily, actually performing the role of top predators and consequently influencing the trophic chain both in natural and agricultural areas. However, despite their protected status, very little information is available regarding their occurrence and ecology. Here, by verifying published studies, collecting personal observations and analyzing novel field data obtained by camera traps, we update their spatial distribution in Sicily, contributing to a better understanding of their habitat use and suggesting future research to improve our knowledge of th…
Experimental and Numerical Analysis of Microstructure Evolution during Linear Friction Welding of Ti6Al4V
2015
Abstract Linear Friction Welding (LFW) is a solid state welding process used to joint bulk components. In the paper, an experimental and numerical study on LFW of Ti6Al4V titanium alloy is presented. A laboratory designed LFW machine has been used to weld the specimens with different contact pressure and oscillation frequency. The joint microstructure has been experimentally observed with SEM and EDS. A dedicated numerical model, able to predict temperature, strain and strain rate distribution as well as the phase volume fraction evolution, has been utilized to predict the final microstructure in the welded parts. It was found that complete transformation of the alpha phase into beta phase …