Search results for "Mass Transfer"

Effect of the height-to-diameter ratio on the mass transfer and mixing performance of a biotrickling filter

2017

BACKGROUND Biotrickling filters (BTFs) are among the most widely used biological technologies for air pollution control. The pollutant removal rate in BTFs relies to a large extent on its gas–liquid mass transfer performance. Therefore, knowledge of the design parameters affecting the mass transfer and mixing performance of full-scale BTFs is of paramount importance. RESULTS This work showed that the height-to-diameter (H/D) ratio is an important parameter in the design of BTFs devoted to air pollution control. The H/D ratio significantly affected the mass transfer and mixing performance of the BTF with and without additional stirring in the holding tank. It was observed that under the same…

Mass transfer and hydrodinamic characteristics of a high aspect ratio self-ingesting reactor for gas-liquid operations

2007

Abstract The mass transfer performance of a gas–liquid self-ingesting stirred reactor is reported both for coalescing and non-coalescing systems. The vessel features are a high aspect ratio and a rather narrow multiple-impeller draft tube, through which the gas phase is ingested and led down to the vessel bottom, where it is finely dispersed into the liquid rising in the annular portion of the vessel. Comparison is made between k L a values determined by several variants of the dynamic method, among which pure oxygen absorption in a previously de-gassed liquid phase. Results show that the gas–liquid mass transfer coefficient values obtained with the last approach are remarkably larger than …

Photoinduced mass transfer in amorphous As 2 S 3 films

2011

The surface relief grating formation in amorphous As2S3 films strongly depends on the polarization state of recording beams. The surface relief grating formation efficiency of s-s and p-p recording beam combination can be essentially enhanced by additional illumination with orthogonal polarization. It is shown that the direction of mass transport on the film surface is determined by the direction of light electric vector (© 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

Characterization of the Altered Zone Around a Fracture in Palmottu Natural Analogue

1996

AbstractA drill core sample penetrating at a natural fracture has been analysed by helium gas techniques and by α-autoradiography. Porosity and diffusivity profiles away from the fracture have been determined and compared with structural profiles. Model calculations are used to determine the effects of sample size on the measured porosities and diffusivities.

The use of non-cavitating coupling fluids for intensifying sonoelectrochemical processes

2020

Abstract For the first time, we have investigated the beneficial effects of non-cavitating coupling fluids and their moderate overpressures in enhancing mass-transfer and acoustic energy transfer in a double cell micro-sonoreactor. Silicon and engine oils of different viscosities were used as non-cavitating coupling fluids. A formulated monoethylene glycol (FMG), which is a regular cooling fluid, was also used as reference. It was found that silicon oil yielded a maximum acoustic energy transfer (3.05 W/cm2) from the double jacketed cell to the inner cell volume, at 1 bar of coupling fluid overpressure which was 2.5 times higher than the regular FMG cooling fluid. It was also found that the…

The modeling of dissimilar welding of immiscible materials by using a phase field method

2013

A multiphysical model of high power beam welding of immiscible materials is developed to explain the influence of operational parameters and materials properties on resulting morphology by simultaneous solving of heat transfer, fluid flow and mass transfer problems. The introduction of phase field description of the interface motion between two immiscible liquids allows obtaining the cartography of melted zone in function of two key-parameters: the position of heat source relatively to joint line and the welding speed. Due to the short thermal cycle limiting mass transfer, high power beam welding techniques may result in very inhomogeneous melted zones. In this study, the interest is paid t…

Numerical Simulation of Turbulent Flows, Heat and Mass Transfer in Metallurgical Induction Processes

2007

Performance of a polypropylene membrane contactor for the recovery of dissolved methane from anaerobic effluents: Mass transfer evaluation, long-term…

2018

Abstract A polypropylene membrane contactor was used for the recovery of dissolved methane from an anaerobic reactor effluent. Effect of operational parameters, operation mode and fouling on long-term operation was studied using vacuum pressure or N 2 as sweep gas. Results were analyzed based on the mass transfer estimations. Lower performance was observed in the shell-side mode due to the lower liquid velocity and the probable channeling. Membrane pore wetting was observed with the increase in Q L in the vacuum-pressure mode. This was confirmed with mass transfer resistance analysis, resulting in an estimated wetted pore fraction of between 0.25 and 0.53. The highest removal efficiencies w…

Modelling of a recirculating photocatalytic microreactor implementing mesoporous N-TiO2 modified with graphene

2020

Abstract The use of microreactors in (photo)catalytic processes offers new possibilities for studying and optimizing many mass and photon transfer limited reactions. In this study, we propose a scalable computational fluid dynamics (CFD) model for the prediction of photocatalytic degradation of a model pollutant (4-nitrophenol) using immobilized N-doped TiO2 grown over reduced graphene oxide (N-TiO2/rGO) in a photocatalytic microreactor working in continuous flow-recirculation mode. The mode of operation used in this study allows the reduction of mass transfer limitations inherent to heterogeneous photocatalytic reactions taking place on immobilized catalysts. A CFD model was developed for …

Autohydrolysis pretreatment of Arundo donax: a comparison between microwave-assisted batch and fast heating rate flow-through reaction systems

2015

Background: Autohydrolysis of lignocellulosic biomass in liquid hot water has been widely studied owing to its high efficiency and relatively low cost. In the perspective of industrial applications, continuous or semi-continuous processes are more interesting than batch systems. Moreover, microwave heating of pretreatment systems has been proposed to intensify the kinetics of the process. In this study, the autohydrolysis of Arundo donax was performed in pure liquid hot water using a microwave-heated batch reactor and a semi-continuous flow-through reaction system with fast heating rate at the same operating conditions with the aim of performing a systematic comparison between the two diffe…