Search results for "Matrix"
showing 10 items of 3205 documents
Optical Properties of Composite Films Based on Copper Chloride in PMMA Matrix
2014
The composite lms based on PMMA, CuCl2 and photoinitiator were prepared.Transmission spectra of the lms with and without photoinitiator were measured. The holo-graphic gratings were recorded, the sensitivity of the lms and surface structure of gratingswere studied. Microanalysis of the lms was performed in di erent part of structure elementsof grating.
Meshless meso-modeling of masonry in the computational homogenization framework
2017
In the present study a multi-scale computational strategy for the analysis of structures made-up of masonry material is presented. The structural macroscopic behavior is obtained making use of the Computational Homogenization (CH) technique based on the solution of the Boundary Value Problem (BVP) of a detailed Unit Cell (UC) chosen at the mesoscale and representative of the heterogeneous material. The attention is focused on those materials that can be regarded as an assembly of units interfaced by adhesive/cohesive joints. Therefore, the smallest UC is composed by the aggregate and the surrounding joints, the former assumed to behave elastically while the latter show an elastoplastic soft…
PLA based biocomposites reinforced with Arundo donax fillers
2014
Abstract In this work, for the first time, a natural and almost inexpensive filler obtained by grinding the culms of Arundo donax was used to prepare PLA based biocomposites. The composites were prepared by melt compounding PLA with A. donax filler (ADF). The influence of the content and size of ADF on the morphology and on the mechanical and thermal properties of PLA–ADF composites was evaluated. Moreover, ADF was extracted from composites to evaluate the effect of processing on morphology and dimensions of the incorporated filler. Furthermore, the experimental elastic moduli of the biocomposites have been fitted, employing two theoretical models, i.e., Hill and Halpin–Tsai. The results sh…
Parameters influencing the stiffness of composites reinforced by carbon nanotubes – A numerical–analytical approach
2014
Abstract Due to their high stiffness and strength, as well as their electrical conductivity, carbon nanotubes are under intense investigation as fillers in polymer matrix composites. The nature of the carbon nanotube/polymer bonding and the curvature of the carbon nanotubes may strongly reduce the reinforcing effect of the carbon nanotubes when added to a matrix to create composites. Here the effects of carbon nanotube waviness and the interaction with the matrix on the stiffness of the composite are investigated. Using a mixed numerical–analytical model, a parametric study of the waviness and volume fraction influence of CNTs on the elastic behavior of the nanocomposite is presented. The m…
CuO nanoparticle filled vinyl-ester resin nanocomposites: Fabrication, characterization and property analysis
2007
Abstract Both unmodified cupric oxide (CuO) nanoparticles and those functionalized with a bi-functional coupling agent methacryloxypropyl-trimethoxysilane (MPS) were used to fabricate vinyl-ester resin polymeric nanocomposites. The nanoparticle functionalization was observed to have a significant effect on the physical properties of the cupric oxide filled vinyl-ester resin nanocomposite. Thermal degradation study by thermo-gravimetric analysis (TGA) showed the increased thermo-stability in the functionalized-nanoparticle-filled vinyl-ester resin nanocomposites as compared with the unmodified-nanoparticle-filled counterparts. The more uniform particle dispersion and the chemical bond betwee…
Impact of the inclusion of hydrotalcite on the morphological and electrical characteristics of an epoxy-based CNT nanocomposite
2012
The experimental results concerning the correlation between morphological and electrical characteristics of a MWCNT/epoxy based composites are presented. The impact of a nanoclay filler is investigated on the DC conductivity of a matrix loaded with different concentrations of MWCNT in order to evaluate the improvements on the dispersion of CNT inside the epoxy matrix. The dispersion is deemed to be very influencing on the electrical conductivity of the nanocomposite. A detailed morphological and structural characterization allows to interpret the electrical behaviour of the nanocomposites. © 2012 IEEE.
Morphology Modification of Polyethylene/Clay Nanocomposite Samples under Convergent Flow
2009
The morphology of PE/CL nanocomposite samples subjected to convergent flows is studied. Elongational flow – the typical flow involved in spinning and film-blowing processing operations – significantly increases with the reduction of the capillary diameter. The values of the convergent extensional stress (calculated by Cogswell's formula) for the PE/CL systems, for all the adopted capillary geometries, are greater than the calculated values for pure polyethylene. The applied convergent flow, at the entrance of the capillary, is able to change the clay morphology and consequently the final material properties on the PE/CL system with limited affinity between the matrix and organo-modified cla…
Comparative performance of electrospun collagen nanofibers cross-linked by means of different methods.
2009
[EN] Collagen, as the major structural protein of the extracellular matrix in animals, is a versatile biomaterial of great interest in various engineering applications. Electrospun nanofibers of collagen are regarded as very promising materials for tissue engineering applications because they can reproduce the morphology of the natural bone but have as a drawback a poor structural consistency in wet conditions. In this paper, a comparative study between the performance of different cross-linking methods such as a milder enzymatic treatment procedure using transglutaminase, the use of N-[3-(dimethylamino)propyl]-N¿-ethylcarbodiimide hydrochloride/ N-hydroxysuccinimide, and genipin, and the u…
Acoustic modes in metallic nanoparticles: atomistic versus elasticity modeling
2009
The validity of the linear elasticity theory is examined at the nanometer scale by investigating the vibrational properties of silver and gold nanoparticles whose diameters range from about 1.5 to 4 nm. Comparing the vibration modes calculated by elasticity theory and atomistic simulation based on the Embedded Atom Method, we first show that the anisotropy of the stiffness tensor in elastic calculation is essential to ensure a good agreement between elastic and atomistic models. Second, we illustrate the reduction of the number of vibration modes due to the diminution of the number of atoms when reducing the nanoparticles size. Finally, we exhibit a breakdown of the frequency-spectra scalin…
Effects of Nylon 6,6 Nanofibrous Mats on Thermal Properties and Delamination Behavior of High Performance CFRP Laminates
2014
none 8 no Nylon 6,6 electrospun nanofibrous membranes interleaved in Carbon Fibre Reinforced Plastic (CFRP) laminates have been proposed as a means to provide a higher threshold value to delamination on structural sites where composites are more prone to develop such failure. A model, highly crosslinked thus inherently brittle, epoxy matrix was selected for its high Young’s modulus and glass transition temperature exceeding 250 °C. The influence of the Nylon 6,6 nanofibres on the curing behaviour of the matrix and on the thermal and dynamic mechanical properties of the cured resin was investigated. These properties were related to the features of the epoxy resin and of the resin impregnated…