Search results for "Matrix"
showing 10 items of 3205 documents
A multilayer anisotropic plate model with warping functions for the study of vibrations reformulated from Woodcock's work
2013
Abstract In this paper, a suitable model for static and dynamic analysis of inhomogeneous anisotropic multilayered plates is described. This model takes into account the variations of the transverse shear strains through the thickness of the plate by means of warping functions. Warping functions are determined by enforcing kinematic and static assumptions at the interfaces. This model leads to: a 10×10 stiffness matrix coupling to each other the membrane strains, the bending and torsion curvatures, and the x and y-derivatives of the transverse shear strains; and a classical 2×2 transverse shear stiffness matrix. This model has been proven to be very efficient, especially when high ratios be…
Vibration of damaged beams under a moving mass: theory and experimental validation
2004
Abstract A theoretical and experimental study of the response of a damaged Euler–Bernoulli beam traversed by a moving mass is presented. Damage is modelled through rotational springs whose compliance is evaluated using linear elastic fracture mechanics. The analytical solution is based on the series expansion of the unknown deflection in a basis of the beam eigenfunctions. The latter are calculated using the transfer matrix method, taking into account the effective mass distribution of the beam. The convective acceleration terms, often omitted in similar studies, are considered here for a correct evaluation of the beam–moving mass interaction force. The analytical solution is then validated…
Influence of correlations between stresses on calculated fatigue life of machine elements
1996
The correlation between components of the random stress tensor and its influence on the calculated fatigue life of machine elements were analysed. Three covariance matrices of components of biaxial stress state were considered. They were determined from measurements of strains in an element of a vibrating screen for aggregate, in the back wall of a bus, and in a welded element of excavator fittings. Calculations were made according to four criteria of multiaxial random fatigue. Cycles were counted with the rainflow method, and damage was cumulated with the Palmgren-Miner hypothesis. It was found that convariances of random stress state components strongly influence the calculated fatigue li…
Fault Detection of Networked Control Systems Based on Sliding Mode Observer
2013
Published version of an article in the journal: Mathematical Problems in Engineering. Also availeble from the publisher at: http://dx.doi.org/10.1155/2013/506217 Open Access This paper is concerned with the network-based fault detection problem for a class of nonlinear discrete-time networked control systems with multiple communication delays and bounded disturbances. First, a sliding mode based nonlinear discrete observer is proposed. Then the sufficient conditions of sliding motion asymptotical stability are derived by means of the linear matrix inequality (LMI) approach on a designed surface. Then a discrete-time sliding-mode fault observer is designed that is capable of guaranteeing the…
A parametric study of curved incrementally launched bridges
2013
Abstract The structural behaviour of incrementally launched bridges in the construction stages depends on different parameters involving deck, nose, supports and guide devices, because static schemes vary continuously with the advance of the deck above the piers. For this reason temporary stresses in the deck, during launching, are rather different from those occurring in service life. Horizontally curved launched bridges also present the effects of torsion induced by geometric curvature. A parametric study is presented in order to analyse the influence of design parameters on the construction of these bridges. Analyses were carried out by extending to curved beams a procedure based on the …
H∞ static output-feedback control design with constrained information for offshore wind turbine system
2013
Abstract This paper deals with H ∞ static output-feedback control design with constrained information for offshore wind turbines. Constrained information indicates that a special zero–nonzero structure is imposed on the static output-feedback gain matrix. A practical use of such an approach is to design a decentralized controller for a wind turbine. This will also benefit the controller in such a way that it is more tolerant to sensor failure. Furthermore, the model under consideration is obtained by using the wind turbine simulation software FAST. Sufficient conditions to design an H ∞ controller are given in terms of Linear Matrix Inequalities ( LMI s ). Simulation results are given to il…
FDTD simulation for electromagnetic radiated emissions in 42 V vehicle electrical systems
2005
In this paper a full 3D approach, based on finite difference time domain method, is used to predict the electromagnetic radiated emissions from 42 V vehicle electrical loads. An experimental set-up has been arranged on purpose. A comparative analysis among measured and computed results is performed. The good agreement obtained among simulated and measured data enables to validate the numerical scheme. The proposed methodology contributes to predict electromagnetic emissions in the automotive environment since the design stage. Moreover, the proposed numerical tool can be used to define, for new vehicle electrical architectures, low cost test methods for electromagnetic compatibility and sui…
Speed and rotor flux estimation of induction motors via on-line adjusted extended kalman filter
2006
This paper deals with the estimation of speed and rotor flux of induction motors via Extended Kalman Filter (EKF) with on-line adjusting of the system noise covariance matrix. The predictor of EKF consists of a discrete time model obtained by means of a second order discretization of the original nonlinear model of the induction motor. In order to obtain accurate estimation of the above mentioned variables, the load torque is included in the state variables and then estimated. Three different system noise models are also illustrated and compared each other by simulations carried out in Matlab/Simulink environment. For one of these models, EKF is adjusted on-line by means of an additional PI…
A new methodology for distribution systems faults identification, location and characterization
2005
PurposeIdentify a new methodology for fault characterization, identification and location in electrical distribution systems, based on the use of matrix algebra.Design/methodology/approachThe developed diagnostic methodology is based on a high precision analytical model of the network using a distributed parameters representation.FindingsTest results have proved the approach to be efficient and precise, while providing a generalized quadripolar model of a line affected by the most common kinds of fault.Research limitations/implicationsGeneralization to a greater number of fault cases, experimental tests.Practical implicationsUtilities are quite interested in such items, since the new requir…
Wideband modeling of cascaded H-plane waveguide junctions using the generalised impedance matrix representation
2009
A strong interest in H-plane waveguide components composed of a large number of cascaded planar junctions is recently renewed. Therefore, the more efficient development of full-wave analysis tools of such devices is again receiving consideration, specially for its potential use within modern design tools. A novel technique for providing the wideband generalised impedance matrix representation of the inductive devices in the form of pole expansions, thus extracting the most expensive computations from the frequency loop is proposed. For such purpose, the whole device is first decomposed into simpler building blocks, i.e. planar junctions and uniform waveguides, which are modelled in terms of…