Search results for "Mechanical engineering"

Downsizing the Electric Motors of Energy-Efficient Self-Contained Electro-Hydraulic Systems by Using Hybrid Technologies

2020

Abstract The ongoing tendency toward the electrification of hydraulic systems, mainly in the form of self-contained solutions, poses design challenges in high-power applications. An electric motor drives positive-displacement machines used to control the motion of the hydraulic actuator (nonhybrid systems encompassing one or two pumps exist in the technical literature). All the power managed by the actuator passes through the electric motor, which leads to often oversized arrangements. These detrimental characteristics are especially pronounced when the power level increases approximately above 35–40 kW. Therefore, this research paper presents and studies a self-contained, electro-hydraulic…

Energy management strategy to reduce pollutant emissions during the catalyst light-off of parallel hybrid vehicles

2020

Abstract The transportation sector is a major contributor to both air pollution and greenhouse gas emissions. Hybrid electric vehicles can reduce fuel consumption and CO2 emissions by optimizing the energy management of the powertrain. The purpose of this study is to examine the trade-off between regulated pollutant emissions and hybrid powertrain efficiency. The thermal dynamics of the three-way catalyst are taken into account in order to optimize the light-off. Experimental campaigns are conducted on a spark-ignition engine to introduce simplified models for emissions, exhaust gas temperature, catalyst heat transfers and efficiency. These models are used to determine the optimal distribut…

Improving the Efficiency and Dynamic Properties of a Flow Control Unit in a Self-Locking Compact Electro-Hydraulic Cylinder Drive

2019

Abstract The introduction of low cost electric motor and drive solutions provides the possibility to design cost competitive compact speed-variable drives as potentially feasible alternatives to conventional valve-controlled solutions. A main drawback in existing self-contained drive technology is the power consumption in stationary load carrying situations. However, the recent introduction of compact self-locking drive topologies with separate forward and return flow lines allow to significantly minimize the power consumption, but introduces another problem. Dependent on the control of the flow device, a continuous, but lower power consumption compared to non-self-locking drive topologies …

Electric relaxation and Mn3+/Mn4+ charge transfer in Fe-doped Bi12MnO20–BiMn2O5 structural self-composite

2016

Fe-doped Bi12MnO20–BiMn2O5 ceramics was sintered at 1130 K for 6 h in ambient air. Two centro-symmetric phases formed thermodynamically stable self-composite material that was deduced from X-ray pattern analysis. The lattice parameters were a = 10.147(8) Å—for the cubic I23 Bi12MnO20 phase; and a = 7.545(4) Å, b = 8.538(1) Å, c = 5.758(3) Å—for the orthorhombic Pbam BiMn2O5 phase. The 57Fe Mössbauer spectrum, recorded at room temperature, has shown pure electronic quadrupolar split. The major doublets reflected the occurrence of Fe3+ ions distributed in two sites, i.e., octahedral Fe4+O6 and square pyramidal Fe3+O5, with preferential occupation of the pyramidal sites, that was consistent wi…

Study Regarding Process of the Electrical Discharge Machining with Magnetic Activation of the Welded Joints of some Materials High Alloy Steel

2021

The scientific paper presents an extensive research on modeling and optimizing the technological parameters of the process for processing by processing electric discharges with massive electrode with and without magnetic activation. Scientific research is based on real data collected from the process of electrical discharges performed on various samples extracted from areas of welded joints of metal components made of high alloy steel. The processing of experimental data was performed both classically and actively, especially the method of the central factorial experiment composed of orthogonal and rotary. The process parameters that were initially modeled and subsequently optimized were ba…

Redox-Tunable Defects in Colloidal Photonic Crystals

2005

The Li Ni0.2Mn0.2Co0.6O2 electrode materials: A structural and magnetic study

2012

Graphical abstract: EPR signal of the Li{sub 0.6}Co{sub 0.6}Ni{sub 0.2}Mn{sub 0.2}O{sub 2} composition showing that Mn{sup 4+} ions are the solely paramagnetic ions in the structure. Highlights: Black-Right-Pointing-Pointer LiCo{sub 0.6}Ni{sub 0.2}Mn{sub 0.2}O{sub 2} was prepared by the combustion method with sucrose as a fuel. Black-Right-Pointing-Pointer Chemical delithiaition was performed by using NO{sub 2}BF{sub 4} oxidizing agent. Black-Right-Pointing-Pointer The rhombohedral symmetry was preserved upon lithium removal. Black-Right-Pointing-Pointer Lithium extraction leads to Ni{sup 2+} oxidation to Ni{sup 4+} followed by Co{sup 3+} oxidation. Black-Right-Pointing-Pointer The EPR narr…

Bipolar electrolysis for tritium recovery from weakly active tritiated water

2001

Abstract Detritiation facilities produce low activity tritiated water from which tritium cannot be recovered. Bipolar electrolysis, based on the electrochemical permeation of hydrogen and its isotopes through Pd–Ag alloy membranes, allows tritiated water enrichment together with negligible gaseous tritium release. Our purpose is to enrich water from 500 Ci/l (1.85×1013 Bq/l) to more than 2000 Ci/l (7.40×1013 Bq/l). We first describe the principle of bipolar electrolysis and its application to isotopic enrichment. The experimental part of this work consists of the determination of the isotopic separation factors. From these experimental values, we simulated the working of an operational cell…

A numerical model for coupled free surface and liquid metal flow calculation in electromagnetic field

2014

Layer-wise and equivalent single layer models for smart multilayered plates

2014

Layer-wise and equivalent single layer plate models for magneto-electro-elastic multiphysics laminates are presented in a unified framework. They are based on variable kinematics and quasi-static behavior of the electromagnetic fields. The electromagnetic state of each single layer is preliminary determined by solving the corresponding governing equations coupled with the proper interface continuity and external boundary conditions. By so doing, the electromagnetic state is condensed into the plate kinematics and the layer governing equations are inferred by the principle of virtual displacements. This approach identifies effective mechanical layers, which are kinematically equivalent to th…