Search results for "Mechanics of Materials"
showing 10 items of 2598 documents
Increasing the flexural capacity of RC beams using steel angles and pre-tensioned stainless steel ribbons
2016
This article presents an experimental programme on reinforced concrete beams retrofitted with steel angles and pre-stressed stainless steel ribbons to increase their flexural strength and ductility. Two different configurations of the steel ribbon were designed, and two companion specimens for each type considered were subjected to a four-point bending test to facilitate a direct comparison in the analysis of the effectiveness of the retrofitting technique. The influence of longitudinal steel angles and transverse stainless steel ribbons is analysed, and the concrete confinement due to stainless steel ribbons examined. The strengthened beams show remarkable increments in flexural strength a…
The use of pumice lightweight concrete for masonry applications
2011
In the last two decades, the use of pumice as lightweight aggregate for concrete in structural applications has been the object of different studies. The aim was to find out if pumice can be an alternative to ordinary lightweight aggregate. The present paper is framed in this context. Here, a study is presented showing the use of pumice for making lightweight concrete units for masonry members. Through the paper, the formulation of a mix design for lightweight concrete is proposed. Then the obtained mechanical characteristics of the masonry units are discussed and compared to the code requirements. Reinforced bearing masonry walls, made with the concrete masonry units in question, were made…
Fibre fragment distribution in a single-fibre composite tension test
2001
Abstract Single fibre fragmentation tests are performed for brittle fibres with Weibull strength distribution and different surface treatments. The fragmentation process is modelled and closed-form expressions for break spacing distribution are obtained. The model accounts for the effect of finite fibre length on the initial fragmentation as well as for break interaction on the advanced fragmentation stage. It is assumed that the exclusion zone due to fibre–matrix interface failure and stress recovery in the fibre is linearly dependent on the applied load. This assumption is validated experimentally. The derived theoretical average fragment length dependence on applied load is used to deter…
Time resolved emission at 1.3 μm of a single InAs quantum dot by using a tunable fibre Bragg grating
2013
Photoluminescence and time resolved photoluminescence from single metamorphic InAs/GaAs quantum dots (QDs) emitting at 1.3 mu m have been measured by means of a novel fibre-based characterization set-up. We demonstrate that the use of a wavelength tunable fibre Bragg grating filter increases the light collection efficiency by more than one order of magnitude as compared to a conventional grating monochromator. We identified single charged exciton and neutral biexciton transitions in the framework of a random population model. The QD recombination dynamics under pulsed excitation can be understood under the weak quantum confinement potential limit and the interaction between carriers at the …
Dissimilar titanium-aluminum skin-stringer joints by FSW: process mechanics and performance
2022
Ever since its inception, friction stir welding (FSW) is being validated by scientific investigations as an effective substitution for fusion-based conventional joining technologies. One of the main strengths of FSW is the possibility to produce dissimilar joints, even using materials extremely different in terms of thermal and mechanical properties. The goal of the present research is to investigate the feasibility of both Al-Ti skin-stringer and reversed Ti-Al skin-stringer joints, highlighting the effect of joint configuration and main process parameters on material flow and joint mechanical properties. During the investigation, the essentiality of the proper heat input through balancing
LA INCLUSIÓN DEL MÉDICO EN LA FORMACIÓN DEL INTÉRPRETE EN EL ÁMBITO SANITARIO
2017
La experiencia docente que describimos en este artículo propone la adquisición y desarrollo de destrezas interpretativas a través de cuatro sesiones teórico-prácticas sobre interpretación en los servicios públicos (ISP). Su particularidad reside en integrar a un profesional del ámbito médico-sanitario en el proceso de aprendizaje, que se perfecciona mediante role plays en el aula. Su colaboración desinteresada, activa y participativa estuvo presente desde la elección de los casos que se abordaron en clase derivados de sus experiencias con pacientes extranjeros, hasta la asunción del papel que habitualmente desempeñan en su trabajo en los ejercicios de simulación con los alumnos. La interacc…
Etude numérique et expérimentale de l'assemblage acier aluminium par soudo-brasage
2006
Dans cet article nous étudions le soudo-brasage de tôles d'acier et d'aluminium (par la technique CMT, assemblage à clin). Ces métaux ont des coefficients de dilatation thermique différents, ce qui provoque des déformations, d'où des contraintes mécaniques élevées. Des expériences sur des éprouvettes, une simulation numérique thermomécanique sont menées en parallèle afin de mieux comprendre ces aspects thermiques et mécaniques dans le but de minimiser la déformation de l'assemblage.
Terahertz Spin‐to‐Charge Conversion by Interfacial Skew Scattering in Metallic Bilayers
2021
The efficient conversion of spin to charge transport and vice versa is of major relevance for the detection and generation of spin currents in spin‐based electronics. Interfaces of heterostructures are known to have a marked impact on this process. Here, terahertz (THz) emission spectroscopy is used to study ultrafast spin‐to‐charge‐current conversion (S2C) in about 50 prototypical F|N bilayers consisting of a ferromagnetic layer F (e.g., Ni81Fe19, Co, or Fe) and a nonmagnetic layer N with strong (Pt) or weak (Cu and Al) spin‐orbit coupling. Varying the structure of the F/N interface leads to a drastic change in the amplitude and even inversion of the polarity of the THz charge current. Rem…
Design Scheme of New Tetragonal Heusler Compounds for Spin-Transfer Torque Applications and its Experimental Realization
2012
Band Jahn-Teller type structural instabilities of cubic Mn(2)YZ Heusler compounds causing tetragonal distortions can be predicted by ab initio band-structure calculations. This allows for identification of new Heusler materials with tunable magnetic and structural properties that can satisfy the demands for spintronic applications, such as in spin-transfer torque-based devices.
Ultrafast Coherent THz Lattice Dynamics Coupled to Spins in the van der Waals Antiferromagnet FePS3
2022
Coherent THz optical lattice and hybridized phonon–magnon modes are triggered by femtosecond laser pulses in the antiferromagnetic van der Waals semiconductor FePS3. The laser-driven lattice and spin dynamics are investigated in a bulk crystal as well as in a 380 nm-thick exfoliated flake as a function of the excitation photon energy, sample temperature and applied magnetic field. The pump-probe magneto-optical measurements reveal that the amplitude of a coherent phonon mode oscillating at 3.2 THz decreases as the sample is heated up to the Néel temperature. This signal eventually vanishes as the phase transition to the paramagnetic phase occurs, thus revealing its connection to the long-ra…