Search results for "Metallurgy"

<title>Irradiation effects in lead zirconate thin films</title>

2003

Lead zirconate PbZrO3 (PZ) and PbZr0.53Ti0.47O3 (PZT) sol-gel films with a thickness of up to 1.5 μm were deposited on TiO2/Pt/TiO2/SiO2/Si substrates by spin coating technique and heterostructures of the same composition as well as on Pb0.92La0.08 (Zr0.65Ti0.35)O3 (PLZT-8) (with a thickness of 0.4 μm) were pulse laser deposited (PLD) on Pt/Ti/SiO2/Si. Observation of a typical antiferroelectric (AFE) double hysteresis loop in obtained PZ heterostructures at room temperature was attributed to the superior dielectric strength in case of thin film materials. The thermal behavior of dielectric permittivity e of PZ film reveals a maximum near 225°C on heating and 219°C on cooling. The higher res…

Interdependence Between Tool Fracture and Wear

1985

Wear and fracture are the main causes of tool scrapping. However fracture plays a major role for increasing values of the hardness and brittleness of tool materials or when low-cobalt tungsten carbides are used or in interrupted cutting conditions where it is the most relevant factor for tool scrapping. In order to obtain the optimal values of the cutting speed both these factors should be considered. The hypothesis of stochastic independence among them simplifies the mathematical formulation of the optimization problem; but experimental investigations do not agree with this assumption and, as a matter of fact, the probability density function of tool fracture results to be dependent on the…

A simplified analysis for the evaluation of stochastic response of elasto-plastic oscillators

1999

Abstract The paper deals with dynamic hysteretic oscillators without post-yielding hardening, called ideal elasto-plastic oscillators, subjected to white noise. They are characterized by the fact that they do not reach stationarity even though excited by stationary stochastic processes. A simplified solution procedure to capture this behaviour is presented in this paper. It is based on modelling the accumulated plastic deformations as a homogeneous compound Poisson process. In particular, two aspects are addressed in the paper: (1) evaluation of the probabilistic parameters of the accumulated plastic deformation process; and (2) evaluation of the second-order cumulants of the response by me…

Influence of Heat Treatment on Fatigue Crack Growth in Ti-6Al-4V Alloy

2011

The paper contains the results of experimental work carried out in order to analyse the initiation and propagation of fatigue cracks in Ti-6Al-4V titanium alloy. The tests were performed on plane specimens with the stress concentrators in form of one-sided sharp notches. The tested specimens were made of the oxygenated Ti-6Al-4V subjected to various variants of heat treatment.

The use of linear regression methods and Pearson’s correlation matrix to identify mechanical–physical–chemical parameters controlling the micro-elect…

2008

Abstract Machining introduces residual stresses at the specimen surface and modifies the microstructure and the texture in a small volume close to the surface. Such changes are important in controlling the corrosion behaviour of machined workpieces in the presence of an aggressive environment. In the present paper, the relationships between cutting parameters and the surface and subsurface characteristics of machined copper were first quantified experimentally using a complete plan of L 8 (2 3 ) and a linear regression method. The influence of surface characteristics on the local polarisation curves of machined surfaces was then investigated. The shear-type crystallographic orientation gene…

Recent advances in local probe techniques in corrosion research – Analysis of the role of stress on pitting sensitivity

2007

Local probe techniques have been largely applied to predict the spatial distribution of the electrochemical reactions and to quantify the corrosion rate. These local probe techniques are now being developed to capture the temporal information, in-situ and in real-time. Nevertheless only few works have been devoted to investigate with these local probes the role of stress on pitting sensitivity on passive materials. In this paper, a part of the most recent studies based on combination of local electrochemical measurements with finite element mapping of surface stress gradients are reported illustrating the role of inclusions under straining and the mechanical effect of surface preparation on…

Physical Chemistry of Electrochemical Processes at the Tip of a Corrosion-Mechanical Crack

2003

Preparation and characterization of (Hg0.7Mo0.3)Sr2(Ca0.7Y0.3)Cu2Ox and (Hg0.9Re0.1)Ba2CaCu2Oy superconducting films by laser ablation

2000

Abstract Oriented (Hg 0.7 Mo 0.3 )Sr 2 (Ca 0.7 Y 0.3 )Cu 2 O x and (Hg 0.9 Re 0.1 )Ba 2 CaCu 2 O y superconducting films were prepared on SrTiO 3 substrates using laser ablation and post-Hg-vapor annealing. Due to the stability of Mo 0.3 Sr 2 (Ca 0.7 Y 0.3 )Cu 2 O x and Re 0.1 Ba 2 CaCu 2 O y in air, no special handling was needed during the grinding, mixing and pressing of the precursor targets. The superconductivity of the films was characterized with the temperature dependence of the ac susceptibility ( χ - T ) and the resistance ( R - T ) while the crystallography was probed with x-ray diffraction (XRD) and scanning electron microscopy (SEM).

Microscopic Studies of YBCO-Based Polycrystalline Materials

1997

Resistivity and irreversibility line of (Hg0.9Re0.1)Ba2CaCu2O6+δ HTS thin films

2003

Abstract High-quality epitaxial (Hg 0.9 Re 0.1 )Ba 2 CaCu 2 O 6+ δ HTS thin films were successfully prepared by pulsed laser deposition (PLD) of Hg-free precursor material on (1 0 0)-oriented SrTiO 3 substrates with subsequent Hg vapour annealing. (Hg 0.9 Re 0.1 )Ba 2 CaCu 2 O 6+ δ HTS thin films exhibit sharp superconducting transitions at T c ≈122 K. The electrical resistance for c -axis oriented HgRe-1212 films has been studied as a function of temperature and dc magnetic fields up to 10 T parallel to the crystallographic c -axis. The irreversibility line for the HgRe-1212 has been deduced from the data and investigated as a function of reduced temperature T / T c . The result of the irr…