Search results for "Metallurgy"

Depth profiles of hardening in lithium fluoride irradiated with swift58Ni ions

2004

The changes of hardness and dislocation formation in LiF crystals irradiated with 630-MeV 58Ni ions up to a dose of 20 MGy were studied by microindentation and dislocation etching techniques. Above the threshold fluence of 2 × 1010 ions/cm2, a marked effect of hardening, which is related mainly to damage processes in the track core, has been observed. Its magnitude depends on ion fluence and energy loss. To investigate the depth distribution of hardening, indentation tests on crystal cross sections cleaved parallel to ion flux were performed. It has been found that the hardness change along the ion path correlates with the ion energy loss and reaches the highest value at the Bragg maximum. …

Europium(III)-doped A(2)Hf(2)O(7) (A = Y, Gd, Lu) nanoparticles: Influence of annealing temperature, europium(III) concentration and host cation on t…

2016

The detailed analyses of structure and luminescence of europium(III)-doped A(2)Hf(2)O(7) (A = Y, Gd, Lu) nanoparticles is presented. Samples were prepared by time and cost effective combustion method that utilize polyethylene glycol both as a chelating agent and as a fuel, with different europium(III) concentrations (from 1 to 12 at.%), annealed at temperatures ranging from 800 to 1400 degrees C, and with alternating A(3+) cation in the A(2)Hf(2)O(7) host. Then, structural variations between materials were analysed by Xray diffraction and structural refinement, while the changes in the luminescence were assessed from the Judd-Ofelt analyses of emission spectra. Nanoparticles prepared at the…

Processing conditions, microstructure and mechanical properties of hetero-nanostructured ODS FeAl alloys produced by spark plasma sintering

2013

International audience; Spark plasma sintering (SPS) has been used to sinter a milled oxide dispersion-strengthened (ODS) FeAl powder in order to prepare dense nanostructured parts. The effect of processing conditions including sintering temperature, holding time and degassing treatments on the microstructure and mechanical properties of the as-sintered materials was investigated. A hetero-nanostructure that contains nano, ultrafine and micrometric grains was confirmed to be developed whatever the processing window, due to the large temperature difference generated during the SPS process itself. The grain size distribution can be tailored by selecting a combination of sintering temperature …

Machining of Steel with Advanced Ceramic Cutting-Tools

1995

The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining

2012

Abstract This paper presents results of an experimental study of cryogenic machining of hardened AISI 52100 steel, focusing on surface integrity. Experiments were performed under dry and cryogenic cooling conditions using CBN tools varying cutting speeds, workpiece hardness and tool geometry. Surface integrity parameters (surface roughness, white layer thickness, residual stresses, metallurgical conditions including grain size, phase transformation, etc.) were investigated to establish the effects of cryogenic cooling on the surface integrity of the machined component, and results were compared with those from dry hard machining. Overall, cryogenic cooling provides improved surface integrit…

Technological aspects regarding machining the titanium alloys by means of incremental forming

2017

Titanium alloys are materials with reduced formability, due to their low plasticity. However, today there are high demands regarding their use in the automotive industry and in bio-medical industry, for prosthetic devices. This paper presents some technological aspects regarding the machinability of titanium alloys by means of incremental forming. The research presented in this paper aimed to demonstrate that the parts made from these materials could be machined at room temperature, in certain technological conditions.

Application of Positron Annihilation Spectroscopy to Studies of Subsurface Zones Induced by Wear in Magnesium and Its Alloy AZ31

2011

Interaction of sliding bodies is an important aspect of numerous applications and subject of many studies (Solecki, 1989). Generally, when two surfaces are loaded together the true contact area is much smaller than the apparent one. The true contact is only at high points or asperities of the surfaces where the interactions in the atomic scale take place. Relative movement between the surfaces leads to friction and wear processes. The rate of wear is controlled by the load, the relative velocity and the behaviour of the material near asperities. The region of asperities can be plastically deformed and the stress is transported to the deeper laying region that becomes elastically deformed (F…

The Annealing Behavior of the Subsurface Zone Induced by Friction in Bismuth Detected by Positron Lifetime Technique

2013

The annealing behavior of the subsurface zone (SZ) in pure bismuth induced by dry sliding was studied using the positron lifetime measurement. This measurement allows us to detect the SZ and its recovery, and recrystallization processes. The comparative measurements of the sample exposed to compression revealed the thermal stability of the SZ. The compressed sample rebuilt its structure due to the recovery and recrystallization processes at the temperature of 60 °C, whereas the sample exposed to dry sliding does it at higher temperature of 260 °C, which is close to the melting point. The isothermal annealing at the temperature of 100 °C confirmed these results. The defect depth profile indu…

Aggregative behavior of cohesive magnesium carbonate powders during fluidization and aerated discharge

2014

In this paper we studied the aerated discharge of two magnesium carbonate powders differing in their average diameter and particle size distribution. These samples were characterized by means of fluidization experiments and rheology shear tests carried out in a rotating shear cell. In the hopper discharge experiments, besides the discharge rates and the mass of residual solids as a function of the aeration rate, the aggregative behavior was observed by means of photographic techniques. Solids aggregates were actually visible within the aerated beds of solids during the fluidization experiments and in the streams of the discharging solids. Experimental data on the powder flow properties and …

Influence of magnesium content on the corrosion resistance of the cut-edges of Zn–Mg-coated steel

2015

Abstract The ability of Zn–Mg coatings (with magnesium content between 5.8 and 15.5 wt.%) to protect steel sheets has been evaluated with local electrochemical techniques (scanning vibrating electrode technique, microcapillary electrochemical cell) and rotating disk electrode, and compared with the corrosion protection afforded by a pure zinc coating. From immersion tests of coated steel cut-edges, it is observed that alloying zinc with magnesium leads to a decrease of the galvanic current between the coating and the steel surface, and to an improvement of the steel corrosion resistance after a drying period, due to the presence of magnesium in the corrosion products.