Search results for "Metallurgy"

Mechanical and microstructural characterization of friction stir welded skin and stringer joints

2013

A microstructural and mechanical investigation on lap joints welded by friction stir welding and made out of a 7075-T6 stringer and a 2024-T4 skin is presented. In particular, the metallurgical and mechanical properties of joints have been studied at different tool feed rates (V = 35, 50, 100 mm/min) and constant rotation speed (R = 500 r/min). Temperature distributions have been monitored during the process. It is found that in the welded area, the recrystallized zone (nugget) has an average grain size of about 3 µm and exhibits coarsened MgZn2 particles on grain boundaries. The maximum values of microhardness in the welded skin increase with the process temperature, while they just sligh…

Quantitative X-Ray Powder Diffraction Analysis of Some Feldspars Used as Raw Material in Ceramics

2001

Texture Effects on Zircaloy Oxidation : Experiment and Simulation

2002

Tool Geometry in Friction Stir Welding of Magnesium Alloy Sheets

2009

Friction Stir Welding (FSW) has been arousing a continuously increasing interest among joining processes since its invention in 1991. Although mainly used for aluminum alloys, it can also be applied to other light alloys. In the present work, experimental and numerical campaigns have been performed with the aim to study the effect of the tool geometry on the mechanical properties of FSW-ed AZ31 magnesium alloy sheets. The results, presented in terms of tensile strength, ductility, micro-hardness values and numerical field variables distributions, allow to reach a deeper knowledge on the behaviour of such relatively new material when FSW-ed, and can be used for a full optimization of the joi…

Mechanical properties and corrosion behaviour of low carbon martensitic stainless steel after machining

2014

The influence of different combinations of cutting conditions on the mechanical behaviour (microhardness), the microstructure and the corrosion behaviour in NaCl solution (using the electrochemical microcell technique and pulse potentiodynamic testing) of a low carbon martensitic stainless steel (grade X4CrNiMo16.5.1 stainless steel) after tempering treatment was studied. Microhardness was increased on the machined surface. In addition, the electrochemical experiments have shown that the machined materials have a heterogeneous electrochemical behaviour. Significant effect of machining on pitting corrosion was noticed. The pitting potential was found to decrease as the microhardness increase…

CDRX modelling in friction stir welding of aluminium alloys

2005

In the paper a numerical model aimed to the determination of the average grain size due to continuous dynamic recrystallization phenomena (CDRX) in friction stir welding processes of AA6082 T6 aluminum alloys is presented. In particular, the utilized model takes into account the local effects of strain, strain rate and temperature; an inverse identification approach, based on a linear regression procedure, is utilized in order to develop the proper material characterization.

White Etching Crack Root Cause Investigations

2014

White etching crack (WEC) failure is distinct to classical fatigue and driven by the composition of lubricants under special loading conditions; for example, slippage and electricity. The white etching area (WEA) within WEC contains carbon supersaturated ferrite (bcc-iron) and carbides, with a size of a few nanometers. This article presents investigations supporting the hypothesis that WEC processes start within a failure-free period by successive accumulation of a structural distortion. This can be measured by acoustic emission. Failure statistics show a steep ascent in the Weibull diagram (s values beyond 1) leading to the assumption that WEC processes start unsuspicious, as one would see…

Frictional behaviour of oxygen diffusion hardened titanium in dry sliding against Co–28Cr–5W–4Fe–3Ni–1Si cobalt alloy

2004

Abstract The results of conformal pin-on-disc tribological tests of a hard layer of the solid solution of oxygen in α-titanium sliding against a Co–28Cr–5W–4Fe–3Ni–1Si cobalt alloy counterspecimen are presented. The α-Ti(O) layer was diffusely produced over 2–8 h of oxidising in the superficial zone of a technical quality titanium specimen. The friction and wear responses of the system were recorded and the wear mechanisms were studied. Investigations of the material structure and chemical constitution in micro-areas of the titanium specimen, cobalt alloy counterspecimen and wear debris formed in dry sliding were performed with a Philips XL20 microscope equipped with an EDAX analyser. Crush…

Fatigue Crack Growth in Titanium and Aluminium Alloys under Bending

2007

The paper contains results of investigations of the crack growth in plane specimens made of Ti-6Al-4V titanium alloy and AlCu4Mg1 aluminium alloy under cyclic bending. The tests were done on specimens with the stress concentrators being one-sided sharp notch. On the fractures there have been observed first of all transcrystalline cracks through the α phase grains for both materials.

Fatigue crack growth in 2024-T351 Friction Stir Welded Joints: longitudinal residual stresses and microstructural effects

2009

Abstract The role of longitudinal residual stress on propagation of fatigue cracks was examined in friction stir welds produced in 2024-T351 aluminum alloy. Fatigue crack growth rate was obtained through constant Δ K Iapp tests for notches at different distances from the weld centerline. Subsequently, crack growth was correlated to weld residual stress measured by the cut-compliance method. It was found that residual stresses correspond to low crack growth rates outside the weld zone during fatigue loading. Once in the weld zone, the crack growth was affected by microstructural and hardness changes. Furthermore, weld residual stresses were mechanically relieved and effects on crack propagat…