Search results for "Metalworking"

Effect of alloy type and casting technique on the fracture strength of implant-cemented structures.

2010

Objectives: To evaluate the influence of alloy type and casting procedure on the fracture strength (FS) of metallic frameworks for implant-supported fixed prostheses. Study design: Thirty three-unit structures for lower posterior bridges were waxed-up and randomly assigned to two groups (n=15) according to alloy type and casting technique: Group 1 (C): cobalt-chromium cast in a centrifugal machine (TS1, Degussa-Hüls); Group 2 (T): titanium cast in a pressure-differential device (Cyclarc II, Morita). Each structure was cemented onto two prefabricated abutments under a constant seating pressure. After 6 months of water aging, samples were loaded in a static universal testing machine (EFH/5/FR…

On the Finite Element Simulation of Secondary Operations on Metallic Foams

2007

Metallic foams have been recently introduced also as industrial materials due to their well known advantages. In fact, their low mass in conjunction with the good thermal and mechanical properties push toward an extensive diffusion in manufacturing industry. In the study here addressed, a very accurate investigation concerning the latter two aspects has been carried out. In fact, a secondary manufacturing process, i.e. the foam bending, has been taken into account. Anyway, all the knowledge derived for sheet metal bending is not directly applicable to the foams. A finite element code has been utilized for modeling the foam behavior during the bending processes and an accurate material rheol…

Experimental Comparison of the MIG and Friction Stir Welding Processes for AA 6005 Aluminium Alloy

2015

In this study, the mechanical properties of welded joints of AA 6005 aluminum alloy obtained with friction stir welding (FSW) and conventional metal inert gas welding (MIG) are studied. FSW welds were carried out on a semi-automatic milling machine. The performance of FSW and MIG welded joints were identified using tensile and bending impact tests, as far as the environmental aspects are also included in the discussion. The joints obtained with FSW and MIG processes were also investigated in their microstructure. The results indicate that, the microstructure of the friction stir weld is different from that of MIG welded joint. The weld nugget consists of small grains in FSW than those found…

Compressive behaviour of laminated structural glass members

2011

Abstract Several experimental investigations in the past few years have highlighted the fact that the compressive strength of glass was significantly higher than its tensile strength, allowing new applications of glass in compression members. However, due to the high slenderness of structural glass elements made of thin glass panels, they tend to fail in a brittle manner. A substantial amount of fundamental research has been carried out in the past few years to investigate the stability behaviour of structural glass elements. However, although buckling of glass panels has been quite well studied, a very poor amount of research has been addressed to glass columns, which by contrast represent…

Linear viscoelastic properties of high reclaimed asphalt content mixes with biobinders

2017

The use of high Reclaimed Asphalt (RA) content mixtures together with binders produced from renewable resources (biobinders) is one of the current challenges in pavement engineering research. On the one hand, RA has been used for decades, but there are still some concerns about its performance, especially when high contents are used (>30%). On the other hand, biobinders are relatively new materials, which have to be deeply characterised and studied in order to develop good practices for their use. In this paper, linear viscoelastic properties of biobinders and bio-mixtures manufactured with high RA content and biobinders are analysed and discussed. High-modulus mixtures with 50% RA were…

A Zone-Casting Technique for Device Fabrication of Field-Effect Transistors Based on Discotic Hexa-peri-hexabenzocoronene

2005

Forming of aluminum foam sandwich panels: Numerical simulations and experimental tests

2006

Abstract The forming of the completed aluminium foam sandwich (AFS) panels would determine an improvement in the manufacturing of parts and panels. In this paper the authors have investigated the formability of AFS through experiments and numerical simulations. As far as the former are concerned, commercially prepared panels have been considered and bending and stamping processes have been taken into account. In addition, FEM analyses have been developed, utilizing a porous material model following the evolution of the material density throughout the forming processes.

Ionic Nitriding of Certain Parts Protected on Nonfunctional Surfaces With Special Paints. Electric Energy Consumed

2021

The experimental researches on the promotion of new technologies for the local protection of metallic parts against plasma nitriding, led to two types of special paints for protection in ionic nitriding, paints elaborated on the basis of copper lamellar powder in combination with magnesium oxide and carbon tetrachloride. In the created context, it was considered that the elaborated paints could be used not only for preventing the hardening during ionic nitriding of certain technological surfaces of the parts on which they are applied, but also for coating certain nonfunctional surfaces, their degasification taking such a long time. These nonfunctional areas could be: surfaces resulted from …

Projected fringes for the measurement of large aluminum ingots

2010

The method of projected fringes is applied to the measurement of the surface topography of aluminum ingots with surface areas of several square meters. The measurements are performed inside the casting hall of an aluminum factory. To meet the challenges encountered in such a demanding environment, it is important to keep the equipment as simple and robust as possible. Therefore a method for locating the fringe positions with sub-pixel accuracy without using for example phase shifting techniques is applied. Also the nonlinearity of the phase when using divergent illumination is discussed. The developed measuring system is tested measuring eight different aluminum ingots, and the results agre…

Conical connection adjustment in prosthetic abutments obtained by different techniques

2019

Background The goal of this study is to compare the misfit (>150µm) generated once the restoration, made by different techniques, is retained to a single conical implant. Material and methods 15 internal connection implants (MIS C1 4'20x10mm) are embedded each one perpendicularly to an horizontal surface of the 1x1x2cm poliuretan resin model. The 15 samples obtained are divided in 5 groups depending on the framework process (n=3): 1/casting, 2/overcasting, 3/Ti-base, 4/milling and 5/laser sintering. The cobalt-chromium alloy frameworks are screw-retained to their respective implants to a 30-Ncm torque. Once it is retained the framework to the implant, the next step is to section the sample …