Search results for "Micro"
showing 10 items of 23412 documents
Experimental Investigation into the Effect of Pyrolysis on Chemical Forms of Heavy Metals in Sewage Sludge Biochar (SSB), with Brief Ecological Risk …
2021
Experimental investigations were carried out to study the effect of pyrolysis temperature on the characteristics, structure and total heavy metal contents of sewage sludge biochar (SSB). The changes in chemical forms of the heavy metals (Zn, Cu, Cr, Ni, Pb and Cd) caused by pyrolysis were analyzed, and the potential ecological risk of heavy metals in biochar (SSB) was evaluated. The conversion of sewage sludge into biochar by pyrolysis reduced the H/C and O/C ratios considerably, resulting in stronger carbonization and a higher degree of aromatic condensation in biochar. Measurement results showed that the pH and specific surface area of biochar increased as the pyrolysis temperature increa…
To incinerate or not? - Effects of incineration on the concentrations of heavy metals and leaching efficiency of post-precipitated sewage sludge (RAV…
2020
The major element and heavy metal concentrations of post-precipitated sewage sludge (PPS) and its ash residue (PPA) were determined using microwave digestion followed by inductively coupled plasma optical emission spectrometry (ICP-OES) and mass spectrometry (ICP-MS). To the best of our knowledge, this has not been previously done. In both PPS and PPA the heavy metal concentrations were clearly below the average concentrations than those encountered in sewage sludge in Europe. The leaching efficiency of the metal (Al/ Fe) used as a precipitation agent from post-precipitated sludge and its ash residue with phosphoric acid was also investigated with previously optimized leaching conditions. T…
Occurrence of antibiotics and antiretroviral drugs in source-separated urine, groundwater, surface water and wastewater in the peri-urban area of Chu…
2020
Recently, there has been an increased interest in bridging the knowledge gap in the occurrence and fate of pharmaceuticals in African urban water cycles. In this study, the occurrence of 7 antibiotics and 3 antiretrovirals in source-separated urine, groundwater, wastewater and surface water of the peri-urban area of Chunga in Lusaka, Zambia, was studied. In groundwater, the pharmaceuticals were only sporadically present with 4 antibiotics and 1 antiretroviral detected. The concentration of the antibiotics ranged from below limit of quantification (<LOQ) to 880 ng/L, with sulfamethoxazole having the highest detection frequency of 42.3%. In the surface water, a comparatively high concentrati…
Using Two-Level Context-Based Predictors for Assembly Assistance in Smart Factories
2020
The paper presents some preliminary results in engineering a context-aware assistive system for manual assembly tasks. It employs context-based predictors to suggest the next steps during the manufacturing process and is based on data collected from experiments with trainees in assembling a tablet. We were interested in finding correlations between the characteristics of the workers and the way they prefer to assemble the tablet. A certain predictor is then trained with correct assembly styles extracted from the collected data and assessed against the whole dataset. Thus, we found the predictor that best matches the assembly preferences.
Mechanical and metallurgical characterization of AA6082-T6 sheet-bulk joints produced through a linear friction welding based approach
2020
In the last decades, new flexible manufacturing processes have been developed to face the demands, by many industrial fields, for highly customized complex functional parts. The peculiar design of these components often overcomes conventional sheet metal and bulk metal forming processes capabilities. In order to face this issue, new hybrid techniques, capable of exploit key advantages of different processes, have to be developed. In this study, a method to obtain sheet-bulk joints, based on the Linear Friction Welding process, is proposed. The feasibility of the technique was investigated through an experimental campaign carried out with varying pressure and oscillation frequency using AA60…
Experimental results on the economic management of a smart microgrid
2020
The aim of this paper is to assess economic benefits deriving from the adoption of a smart microgrid. To this end, a case study consisting of 250 houses connected to the distribution network through a MV/LV transformer substation has been investigated and implemented in the experimental microgrid built at the Polytechnic University of Bari, Italy. The analysis has been performed by comparing three different energy providers: the utility grid, the utility grid with the inclusion of non-programmable renewables generators, and the inclusion of such residential loads into a smart microgrid. The obtained results demonstrated that with the adoption of a smart microgrid significant costs savings c…
Surface and mechanical characterization of stationary shoulder friction stir welded lap joints: experimental and numerical approach
2020
Friction Stir Welding (FSW) is one of the most used solid-state welding processes in the aeronautical, aerospace, ground transportation and naval fields. Stationary Shoulder Friction Stir Welding (SSFSW) is a recently introduced variant of the process allowing lower heat input into the joints, with beneficial effects in terms of joint mechanical properties, microstructure and top surface finish. In the paper, lap joints produced by SSFSW and made out of AA6082-T6 aluminum alloy sheets have been analyzed with the aim to investigate the effect of the stationary shoulder on the lap joints surface, metallurgical, and mechanical properties. The lap joints produced by SSFSW have been compared to …
Method for 3D fibre reconstruction on a microrobotic platform
2015
Automated handling of a natural fibrous object requires a method for acquiring the three-dimensional geometry of the object, because its dimensions cannot be known beforehand. This paper presents a method for calculating the three-dimensional reconstruction of a paper fibre on a microrobotic platform that contains two microscope cameras. The method is based on detecting curvature changes in the fibre centreline, and using them as the corresponding points between the different views of the images. We test the developed method with four fibre samples and compare the results with the references measured with an X-ray microtomography device. We rotate the samples through 16 different orientatio…
Prediction-Based Assembly Assistance System
2020
This paper presents the design of a prediction-based assembly assistance system for manual operations and the results obtained on the data collected from experiments of assembling a customizable product. We integrated into the proposed system a Markov predictor improved with a padding mechanism whose role is to recommend the next assembly step and to detect the worker’s errors. The predictor is trained with correct assembly patterns and tested with real assembly/manufacturing data. The proposed predictor improves the coverage and, thus, there is a significantly higher number of assembly steps which are correctly correlated with the real intentions of the workers.
Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H 3 PO 4 /H 2 SO 4
2017
Abstract In recent decades, new manufacturing processes have been developed such as Thermal Spray Coating (TSC) and Additive Layer Manufacturing (ALM), which reduce or avoid machining of parts with complex geometries. This study aims to develop an Electropolishing (EP) process for TSC and ALM 316L Stainless Steel (SS). EP is an anodic dissolution process currently used in industry to reduce surface roughness and obtain a bright and smooth finish. The EP mechanism was studied, in a mixture of H3PO4 and H2SO4, for TSC, ALM and “cast” SS in order to determine the best conditions (time, temperature, potential). Special attention was paid to surface characterization by combining several techniqu…