Search results for "Micro"
showing 10 items of 23412 documents
A numerical model for Wire integrity prediction in Friction Stir Extrusion of magnesium alloys
2017
Abstract A numerical model for the prediction of the wire quality produced by the novel direct machining chip recycling technique known as Friction Stir Extrusion (FSE) is presented. Wire microstructure and wire integrity have been predicted by embedding in the code the equations enabling the calculation of the Zener-Hollomon parameter as well as the W parameter of the Pivnik-Plata solid bonding criterion. The proposed model, developed for the AZ31 magnesium alloy using the commercial simulation package DEFORM, is 3D Lagrangian, thermo-mechanically coupled with visco-plastic material behavior. The model was first validated against experimental temperature measurements and then used to predi…
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
In-process control strategies for friction stir welding of AZ31 sheets with non-uniform thickness
2017
Two different in-process control strategies were developed and compared with the aim to produce AZ31 magnesium alloy joints by friction stir welding on sheet blanks with a non-uniform thickness. To this purpose, sheets with dip or hump zones were welded by either changing the rotational speed or the tool plunging in order to keep constant the value of the vertical force occurring during the welding stage of the process. The influence of the main process parameters on the tool force, the micro- and macromechanical properties, and the joints microstructures in the dip and hump zones were analyzed. The results showed that using the rotational speed change-based approach, the hump zones are sub…
Innovative method to estimate state of charge of the hydride hydrogen tank: application of fuel cell electric vehicles
2021
International audience; Significant attention has been paid to metal hydrides (MH) as an environmentally friendly and safe way to store hydrogen. This technology has considerable potential for the application of embedded hydrogen storage in fuel cell electric vehicles, but its widespread application faces a major problem in terms of estimating the remaining hydrogen amount in the tank. In this work, a new method is proposed for estimating the state of charge (SoC) of the hydrogen hydride tank (HHT) by application of piezoelectric material. The idea is to cover the entire inner wall of the metal-hydride tank with a layer of piezoelectric material. During the process of hydrogen absorption, t…
Microstructure and mechanical properties of dissimilar Ti/Nb/Cu/steel laser joints
2020
Abstract The absence of intermetallic phases in Fe/Cu, Cu/Nb and Nb/Ti binary systems opens the possibility to obtain reliable joints between titanium alloys and steels by using a multimaterial copper/niobium insert. Continuous Yb:YAG laser welding of 1 mm thick titanium and 316L stainless steel plates through niobium/copper multimaterial insert was performed. The use of a 100 µm laser beam allowed producing isolated molten zones and thus completely avoiding the formation of brittle intermetallic phases, according to SEM and XRD analysis. The effect of energy per unit length applied to the niobium/copper welds on the mixing process and mechanical properties of the joints was investigated. A…
Improving surface integrity of additively manufactured GP1 stainless steel by roller burnishing
2020
Abstract Additive manufacturing can rapidly fabricate the desired components by selectively melting and solidifying feedstock, rather than conventional subtractive machining. However, the difference between the two routes in terms of surface integrity of the final component is relevant. This paper presents a strategy to control the surface characteristics of additively manufactured stainless steel by roller burnishing. In particular, process parameters have been carefully selected to improve the surface integrity of the worked material. The quality of the surface has been analyzed in terms of roughness, hardness, microstructure and residual stresses. The overall product endurance under high…
Linear friction welding of dissimilar AA6082 and AA2011 aluminum alloys: microstructural characterization and design guidelines
2015
This paper presents the results of an experimental and numerical campaign on Linear Friction Welding of dissimilar AA2011-T8 and AA6082-T6 aluminum alloys. Experimental tests were carried out with constant oscillation amplitude and process time. Varying oscillation frequency, interface pressure, specimen geometry and mutual position were used. Grain size measurements, HV tests and EDX analysis were considered to characterize the microstructure of the joints as a function of the input process parameters. A thermal numerical model was utilized to predict the temperature profiles in the joints during the process. The obtained results allowed the identification of four weld categories: sound jo…
Direct laser welding of pure titanium to austenitic stainless steel
2018
Abstract Direct butt joining of pure titanium to 316L stainless steel with continuous Yb:YAG laser was performed with variation of the beam offset from joint line. Mechanical properties of samples were evaluated by tensile tests and three-point flexural tests. The fractured surfaces and cross sections of welds were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Tensile properties of welds were strongly determined by the beam offset from joint line and are well described by Weibull statistics. Ultimate tensile strength of 174 ± 69 MPa and ultimate flexural strength of 297 ± 48 MPa were obtained. Brittle fracture took place in…
Impact des conditions d'usinage sur la zone du matériau affectée par le procédé
2007
Colloque avec actes et comité de lecture. Internationale.; International audience; Les procédés d'usinage peuvent créer des contraintes résiduelles à la surface des pièces usinées et ainsi modifier la microstructure et la texture de la matière proche de la surface. De tels changements sont importants pour l'étude du comportement des pièces au cours du temps. Il est alors nécessaire de quantifier les contraintes résiduelles, les composantes de texture et de déterminer la microstructure induite par l'usinage pour comprendre et prédire le comportement des surfaces considérées. Dans cette étude, le matériau cuivre pur a été choisi et considéré comme un "système modèle". En tournage, l'influence…
Application of linear friction welding for joining ultrafine grained aluminium
2020
Abstract Ultrafine grained (UFG) materials are of great potential in industry due to their enhanced mechanical strength and other promising features, such as ability to superplastic deformation or excellent corrosion resistance. Nevertheless, one of the main limitations lies in their low thermal stability, which leads to excessive grain growth at elevated temperature. It influences mainly further processes performed at high temperature, such as joining. It causes detrimental problems during conventional fusion welding, as significant grain growth is observed and therefore the advantages as a result of small average grain size disappear. Therefore, the idea of applying solid state joining pr…