Search results for "Microstructure"

VIEPS/Mainz Microstructure Course

2000

Effect of some additives on the development of spinel-based glass-ceramic glazes for floor-tiles

2005

Abstract The feasibility of developing spinel-based glass-ceramic glazes from a glass with composition in the system ZnO–MgO–B 2 O 3 –Al 2 O 3 –SiO 2 was examined. To do it additional fluxes and/or nucleants were added to a parent glass before melting. Pressed pellets of powdered glasses were submitted to standard thermal treatments up to 1200 °C. The crystallization path and the microstructural development at several temperatures were followed by several experimental techniques. The results showed that additions of TiO 2 as nucleant or additional B 2 O 3 as flux to the chosen glass favored the crystallization of cordierite or mullite as main crystalline phase. Glasses which also contained …

Coupling Lagrangian simulation models and remote sensing to explore the environmental effect on larval growth rate: The Mediterranean case study of r…

2023

The relationship between environmental conditions and early life-history traits of Sardinella aurita are investigated using material collected in two sites of the Central Mediterranean Sea. Individual mean daily growth during the planktonic phase has been determined by using otolith microstructure analysis, while Lagrangian simulation models allowed to estimate the daily position in space and time of each specimen from the hatching to the catch. Generalized Additive Mixed Models (GAMMs) have been implemented to explore the impact of environmental conditions at time t, t-1 day and t-2 days on the mean daily growth rate occurring at time t. Spatial analysis evidenced a wide dispersion of eggs…

The role of nanopowder particle surfaces and grain boundary defects in the sintering of ZnO ceramics

2012

This work focuses on the characteristics of sintered ZnO ceramics and explores the role of source powder morphology in the process of sintering. The source ZnO powders had grained (d = 100 nm) and tetrapod-like (d=50-100 nm, l=3−10 μm) morphologies, they were compacted and sintered at 1200° C. The results have shown that ceramics sintered from the grained powder exhibit relatively high (8%) porosity at grain boundaries and as cavities within grains, which facilitates brittleness. Photoluminescence spectra for these ceramics besides a narrow exitonic band contain a broad "green" luminescence band attributed to defect states. The second ceramics sintered from the tetrapod-like powder has lowe…

Electronic microdiffraction study of structural modifications resulting from the dehydration of gypsum. Prediction of the microstructure of resulting…

2001

Abstract Endothermic decomposition reactions (solid 1→solid 2+gas) generally affect only part of the inter-atomic bonds of the solid 1 structure. In consequence, the morphology and external dimensions of particles remain unchanged (the particles of solid 2 are referred to as pseudomorphs of those of solid 1). The gas release normally leads to a decrease of the molar volume of the precursor solid, resulting in cracking and formation of intra-particle porosity. This work deals with such a reaction: the dehydration of gypsum into sub-hydrated and anhydrous phases. Ultrathin (010) gypsum cleaved plates have been dehydrated under controlled conditions and studied by electron microdiffraction. Al…

Fabrication of elastomeric scaffolds with curvilinear fibrous structures for heart valve leaflet engineering

2014

Native semi-lunar heart valves are composed of a dense fibrous network that generally follows a curvilinear path along the width of the leaflet. Recent models of engineered valve leaflets have predicted that such curvilinear fiber orientations would homogenize the strain field and reduce stress concentrations at the commissure. In the present work, a method was developed to reproduce this curvilinear fiber alignment in electrospun scaffolds by varying the geometry of the collecting mandrel. Elastomeric poly(ester urethane)urea was electrospun onto rotating conical mandrels of varying angles to produce fibrous scaffolds where the angle of fiber alignment varied linearly over scaffold length.…

Heat-Resistant Fully Bio-Based Nanocomposite Blends Based on Poly(lactic acid)

2013

Poly(lactic acid) (PLA) is melt mixed with polyamide 11 (PA11) to obtain a heat-resistant fully bio-based blend with PLA as the dominant component. The goal is achieved by adding small amounts of organoclay (OMMT), which is used to manipulate the blend microstructure. The selective positioning of the OMMT inside the PA11 and at the PLA/PA11 interface turns the blend morphology from drop/matrix into co-continuous at high PLA content (70 wt%). The OMMT-rich PA11 framework that interpenetrates the major PLA phase effectively contributes to bear stresses, and the nanocomposite blend keeps its structural integrity up to ≈160 °C, i.e., about 100 °C above the PLA glass transition.

Microstructure and property of titanium heterogeneous laser welding

2015

International audience; Dissimilar welding has been investigated for three different couples of titanium alloys: α/α+β, α/β and α+ββp. Plates of 100 x 60 x 1.6 or 1.8 mm were welded with a Yb: YAG laser. Tensile tests show that the properties of the dissimilar welded specimens were generally controlled by Those of the weakest material except for the α+β/β where the ultimate tensile strength was approximately equal to the average value of both materials. In every case, the welding sample elongation was found to be smaller than that of the base metals. The rupture took place away from the bead and was found to be always located in the alloy having the lowest mechanical properties. Nevertheles…

Dissimilar laser welding of AISI 316L stainless steel to Ti6–Al4–6V alloy via pure vanadium interlayer

2015

Abstract Successful continuous laser joining of AISI 316L stainless steel with Ti6Al4V titanium alloy through pure vanadium interlayer has been performed. Three welding configurations were tested: one-pass welding involving all three materials and two pass and double spot welding involving creation of two melted zones separated by remaining solid vanadium. For the most relevant welds, the investigation of microstructure, phase content and mechanical properties has been carried out. In case of formation of a single melted zone, the insertion of steel elements into V-based solid solution embrittles the weld. In case of creation of two separated melted zones, the mechanical resistance of the j…

Welding abilities of UFG metals

2018

Ultrafine Grained (UFG) metals are characterized by an average grain size of <1 μm and mostly high angle grain boundaries. These materials exhibit exceptional improvements in strength, superplastic behaviour and in some cases enhanced biocompatibility. UFG metals barstock can be fabricated effectively by means of Severe Plastic Deformation (SPD) methods. However, the obtained welded joints with similar properties to the base of UFG material are crucial for the production of finished engineering components. Conventional welding methods based on local melting of the joined edges cannot be used due to the UFG microstructure degradation caused by the heat occurrence in the heat affected zone…