Search results for "Microstructure"
showing 10 items of 707 documents
Influence de l'état protéique sur la dynamique de séparation de phase et de gélification dans un système ternaire aqueux à base de protéines de pois …
2012
Two aqueous systems at 20°C in 0.1 M NaCl and pH 7.2 containing globular pea proteins and sodium alginate were investigated in this study. First, phase behavior of (i) either low-denatured mixed globulins or (ii) their thermally pre-aggregated counterparts - alginate mixtures was compared using a multi-scale approach, by means of phase diagram and microstructure analysis by confocal microscopy. Thermodynamic incompatibility was the main driving force leading to phase separation within the mixtures, which presented according to their initial biopolymer composition both different morphological and time-evolution features of coexisting phases. Thereafter, a cold-set gelation for each system wa…
Structural and hydrogenation study on the ball milled TiH2–Mg–Ni
2015
International audience; With the aim of further understanding for TieNieMg alloys and their hydrogenation behavior, powders of TiH2, Mg and Ni with the molar ratio of 3:1:2 have been mechanically milled for 10 h, 20 h, 30 h, 40 h according to the stoichiometry (TiH2)1.5Mg0.5Ni. Microstructures of the milled sample were analyzed and their hydrogenation properties as negative electrodes for Ni-MH batteries were studied. Phase change with milling time revealed the fast formation of the Ti-Mg-H FCC phase. The alloying priority among Ti, Mg and Ni was demonstrated by comparing phase compositions in different milling time. Hydrogen capacities evaluated by both solidegas reaction and electrochemic…
Microstructuration des dépôts imprimés par jet d'encre de la coalescence des nanoparticules d'argent vers la réalisation d'interconnexions de composa…
2012
Several challenges are still holding back the technological transfer of printed electronics to industry in spite of recent progresses. In this thesis work, the printing method of inks based on silver nanoparticles (=25 nm) was optimized according to its rheology and to the fluid/substrate interactions for the fabrication of electrical interconnections with a thickness of 500 nm. These lines were printed on silicon or flexible substrates and annealed either by conventional (oven or infrared) or selective methods (microwave) at temperatures comprised between 100 and 300 °C.A better understanding of the relationship between process and microstructure of these printed thin films, based on sever…
High bit rate optical pulses sources generation and microstructured chalcogenide fibers characterizations
2011
This memory of thesis s' registered voter in the context of the FUTUR project financed by l'ANR and concerning the development of optical finctions fot the high bit-rate transmissions in the Network heart and carries on very high rates optical fibers sources generation and the optical chalcogenide microstructured fiber charaterization. For this purpose, we study the linear and non-linear characteristics of microstructured chalcogenide fibers conceived and realized in various collaborations within the framework of the ANR FUTUR project. For that a great number of characterizations methods were developed giving a comparison between a standard single mode fiber and there microstructured chalco…
Fiber-based light source for biomedical applications
2013
This manuscript presents the work done concerning the development of a light source used for biomedical imaging and more particularly for coherent Raman scattering imaging. In fact an efficient broadcasting of these ones is hampered by the need of two synchronized and wavelength shifted pulses. As so, the handiness and frequency conversion capabilities of nonlinear fiber optics are used to circumvent this technological lock. First of all, an easy wavelength tunable source is set by the use of the self-shifting in optical frequency of a soliton. A study of the main fiber parameters lead to shifts of 320 to more than 500 nm which allows interesting molecular resonances imaging (≈ 1000-4000 cm…
Céramiques diélectriques commandables pour applications micro-ondes : composites à base de titanate de baryum-strontium et d'un oxyde non ferroélectr…
2001
Since the last decades, dielectric ceramics have been considered as attractive for microwave applications as tunable dielectric resonators or phase shifters. For that, ceramic devices should be tunable – change in dielectric constant with applied voltage- with moderate to low dielectric constant (30 to 1000) and loss tangent as low as possible. To reconcile these properties, composite ceramics based on Ba0.6Sr0.4TiO3 (BSTO) and a non-ferroelectric oxide with a low dielectric constant (MgTiO3 or MgO) were synthesised. The aim of this study was to correlate the microstructure with the dielectric properties, especially the Curie temperature and the dielectric relaxation phenomena.Ceramics with…
Microstructures in shells of the freshwater gastropod Viviparus viviparus: a potential sensor for temperature change?
2013
Abstract Mollusk shells contain a plethora of information on past climate variability. However, only a limited toolkit is currently available to reconstruct such data from the shells. The environmental data of some proxies (e.g. Sr/Ca ratios) is obscured by physiological effects, whereas other proxies, such as δ 18 O, simultaneously provide information on two or more different environmental variables. The present study investigates whether microstructures of the freshwater gastropod Viviparus viviparus provide an alternative means to reconstruct past water temperature. Cold and highly variable temperature regimes resulted in the precipitation of highly unordered first-order lamellae of simp…
Šķirkļa struktūras analīze biznesa terminu vārdnīcās
2019
Šajā pētījumā tika veikta biznesa terminu vārdnīcu šķirkļa struktūras analīze. Pētījuma mērķis bija analizēt un salīdzināt šķirkļa struktūru biznesa terminu vārdnīcās drukātajā un elektroniskajā vidē, lai parādītu atšķirības starp tām. Šajā pētījumā tika pielietotas literatūras apskata un šķirkļa struktūras satura analīzes metodes. Rezultāti ir parādījuši, ka ir daudz atšķirību starp drukātās vides un elektroniskās vides biznesa terminu vārdnīcām, tai starpā informācijas daudzveidības ziņā. Galvenais šī pētījuma secinājums ir tas, ka pastāv atšķirības starp izvēlētajām drukātās un elektroniskās vides biznesa terminu vārdnīcu šķirkļa struktūrām, kas izceļ atšķirības starp šķirkļa struktūru o…
Dual phase titanium alloy hot forging process design: experiments and numerical modeling
2015
Titanium alloys are considered desirable materials when both good mechanical properties and weight reduction are required at the same time. This class of materials is widely used in those fields (aeronautics, aerospace) in which common steels and light-weight materials, e.g., aluminum alloys, are not able to satisfy all operative service conditions. During the last decade, forging of titanium alloys has attracted greater attention from both industrial and scientific/academic researchers because of their potential in providing a near net shaped part with minimal need for machining. In this paper, a numerical model of the forging sequences for a Ti-6Al-4V titanium alloy aerospace component is…
Influence of M23C6 carbides on the heterogeneous strain development in annealed 420 stainless steel
2020
Understanding the local strain enhancement and lattice distortion resulting from different microstructure features in metal alloys is crucial in many engineering processes. The development of heterogeneous strain not only plays an important role in the work hardening of the material but also in other processes such as recrystallization and damage inheritance and fracture. Isolating the contribution of precipitates to the development of heterogeneous strain can be challenging due to the presence of grain boundaries or other microstructure features that might cause ambiguous interpretation. In this work a statistical analysis of local strains measured by electron back scatter diffraction and …