Search results for "Microstructure"
showing 10 items of 707 documents
Larval fish assemblages in the central Mediterranean Sea: spatio spatio-temporal dynamics and biological effect on early life stage of Sardinella aur…
Wpływ składu chemicznego i mikrostruktury na odporność stali na niszczenie wodorowe
2014
W pracy przedstawiono podsumowanie dotychczasowych wyników badań i poglądów dotyczących czynników wywierających wpływ na odporność stali na niszczenie wodorowe. O degradacji stali eksploatowanych w warunkach oddziaływania wodoru w głównej mierze decyduje ich stan, a w szczególności mikrostruktura,technologia wytwarzania oraz defekty występujące w ich strukturze.
Effect of in Doping on the ZnO Powders Morphology and Microstructure Evolution of ZnO:In Ceramics as a Material for Scintillators
2018
Transparent ZnO ceramics are of interest for use as material for high-efficiency fast scintillators. Doping ZnO ceramics in order to improve complex of their properties is a promising direction. In the present research, the role of indium in the ZnO nanopowders surface interactions and in the change of microstructures and photoluminescence (PL) characteristics of sintered cera-mics is considered. Undoped and 0.13 wt% In doped ZnO ceramics are obtained by hot pressing sintering. It has been found that indium leads to the transition of initially faceted ZnO particles to rounded, contributing to good sintering with formation of diffusion active grain boundaries (GBs). Unlike ZnO ceramics, ZnO:…
Surfactant-assisted synthesis of Cd1−xCoxS nanocluster alloys and their structural, optical and magnetic properties
2010
We report the synthesis of Co-doped CdS nanoclusters (Cd1−xCoxS) for different doping concentrations (x = 0.10, 0.20 and 0.30) and characterization of their structural, optical, and magnetic properties. The structural properties studied by X-ray diffraction revealed hexagonal-greenockite structure and a decrease of the lattice parameters (a and c) with doping, showing incorporation of Co in the lattice. The morphology of the nanoclusters was studied by scanning electron microscopy. The optical absorption studies, using diffused reflectance spectroscopy, revealed that Co doping modifies the absorption band edge. Ferromagnetic phase was observed in the magnetization measurements at room-tempe…
Microstructure Characteristics of Unsaturated Compacted Scaly Clay
2012
Microstructure characteristics of unsaturated compacted scaly clay are investigated by MIP tests on freeze dried samples and observation of SEM photomicrographs. Effects of scale microstructure and increasing compaction stresses, and microstructure changes induced by loading and unloading paths and clay saturation are analysed.
Effects of Temperature and Axial Strain on Four-Wave Mixing Parametric Frequencies in Microstructured Optical Fibers Pumped in the Normal Dispersion …
2014
A study of the effect of temperature and axial strain on the parametric wavelengths produced by four-wave mixing in microstructured optical fibers is presented. Degenerate four-wave mixing was generated in the fibers by pumping at normal dispersion, near the zero-dispersion wavelength, causing the appearance of two widely-spaced four-wave mixing spectral bands. Temperature changes, and/or axial strain applied to the fiber, affects the dispersion characteristics of the fiber, which can result in the shift of the parametric wavelengths. We show that the increase of temperature causes the signal and idler wavelengths to shift linearly towards shorter and longer wavelengths, respectively. For t…
Suction controlled drying and wetting cycle effects on the volumetric behaviour of a lime-treated high plasticity clay
2016
The paper presents some experimental results collected on samples recovered from an experimental embankment obtained by compacting a lime-treated clay. Samples were collected soon after the in situ compaction and they were cured in controlled environmental conditions for at least 18 months. Mercury intrusion porosimetry tests (MIP) were carried out on freeze-dried specimens to characterize the microstructure of the material. In order to assess the durability of the improved material, laboratory tests focused on the effects of cyclic variations of the degree of saturation on the water retention properties and the volumetric behaviour of the stabilized clay. Collected results show that the li…
Erratum: Mangas-Sanjuán, V.; et al. Assessment of the Inter-Batch Variability of Microstructure Parameters in Topical Semisolids and Impact on the De…
2020
Demonstration of similar microstructure is essential for demonstrating the equivalence of generic topical products since the microstructure of semisolids may affect the drug release. The objective of this study was to compare the microstructure-defining physical parameters of different batches of a reference ointment containing calcipotriol and betamethasone (Daivobet 50 µg/0.5 mg/g) in order to define the acceptance range that allows concluding equivalence between these batches. Being batches of the same reference product, they are expected to be clinically equivalent and possess similar microstructure. The 90% confidence intervals for the test/reference ratio of these physical parameters …
Optimizing the Shape of Welded Constructions Made through the Technique “Temper Bead Welding”
2020
Welded constructions are subject to high stresses during operation. One solution for improving the behavior in exploitation of welded constructions in various cases is to use the welding technique “temper bead welding” (TBW). In the paper, the optimization of the geometry of the welded joints by the TBW technique was performed. Thus, corner welded joints made of S355 steel were analyzed. To make the welded joints, three layers of welding seams were deposited, and the intermediate layers were processed through cutting with various radii. To analyze the influence of the size of these rays on the behavior of welded constructions, a research program based on factorial experiences wa…
Softening of Silica Filled Styrene-Butadiene Rubber under Uniaxial Cyclic Loading
2016
Stress-strain behaviour of silica filled styrene-butadiene rubber showed strong hysteresis and cyclic softening, while these effects were almost negligible for the neat rubber. Significant Mullins effect occurs between the first and second loading cycles, whereupon samples reach their steady state after four repeated cycles. The degree of softening increases with volume content of silica characterizing the softening effect as a breakdown of the filler-formed microstructure defined by both, specific interactions in the filler associations and between the filler and rubber matrix. Contribution of different damage mechanisms to the total energy losses on different stages of extension was estim…