Search results for "Modeling and Simulation"
showing 10 items of 1561 documents
Investigation of the hemodynamic flow conditions and blood-induced stresses inside an abdominal aortic aneurysm by means of a SPH numerical model.
2019
The estimation of blood flow-induced loads occurring on the artery wall is affected by uncertainties hidden in the complex interaction of the pulsatile flow, the mechanical parameters of the artery, and the external support conditions. To circumvent these difficulties, a specific tool is developed by combining the aorta displacements measured by an electrocardiogram-gated-computed tomography angiography, with the blood velocity field computed by a smoothed particle hydrodynamics (SPH) numerical model. In the present work, the SPH model has been specifically adapted to the solution of the 3D Navier-Stokes equations inside a domain with boundaries of prescribed motion. Images of the abdominal…
Temperature control during Spark Plasma Sintering and application to up-scaling and complex shaping
2013
International audience; The determination and the homogeneity of the sample temperature during consolidation of powders by Spark Plasma Sintering (SPS) are addressed. Densifications were carried out in three different facilities differing by their constructors and their size. A structural transformation activated in a TiAl alloy was used as a marker of the sample temperature and finite element modeling were performed to evaluate the temperature at each point of the set-up. A good agreement between experimental and simulated data is exhibited. Alloys with identical microstructures were sintered and the homogeneity of the microstructure was better in the largest machines or when the sample wa…
WEAR PERFORMANCE OF CERAMIC CUTTING-TOOL MATERIALS WHEN CUTTING STEEL
1991
Abstract Some test cycles have been carried out in continuous cutting conditions, employing cutting parameters (feed, depth of cut and cutting speed) chosen following experimental planes and suitable test fields. The wear tests have been carried out on AISI 1040 steel with cutting speeds from 5m/sec to 11m/sec. The silicon nitride, sintered carbide, cubic boron nitride and alumina reinforced with SiC whiskers inserts, have shown, at each assigned cutting parameter, poor wear resistance when cutting steel. Alumina and alumina in submicron grain, which has been toughened by ZrO2 phase transformation, and the oxide-based alumina, have been the better wear resistance. The mixed based alumina ha…
Composite layer-based analytical models for tool–chip interface temperatures in machining medium carbon steels with multi-layer coated cutting tools
2006
Abstract This investigation is devoted to the thermal problems in dry orthogonal turning of a C45 medium carbon steel with natural contact tools treated with multi-layer coatings with an intermediate Al 2 O 3 layer. New hybrid analytical models for estimating heat partition to the chip and the tool–chip interface temperatures were proposed. Furthermore, the physics-based modelling concept, which applies composite layer approach was developed to estimate the average and maximum steady-state tool–chip interface temperatures in orthogonal turning. The model predictions were compared to appropriate experimental process data using natural tool-work thermocouples and other simulated and measured …
The development of nature-inspired gripping system of a flat CFRP strip for stress-ribbon structural layout
2021
Abstract The elegant stress-ribbon systems are efficient in pedestrian bridges and long-span roofs. Numerous studies defined corrosion of the steel ribbons as the main drawback of these structures. Unidirectional carbon fiber-reinforced polymer (CFRP) is a promising alternative to steel because of lightweight, high strength, and excellent corrosion and fatigue resistance. However, the application of CFRP materials faced severe problems due to the construction of the anchorage joints, which must resist tremendous axial forces acting in the stress-ribbons. Conventional techniques, suitable for the typical design of the strips made from anisotropic material such as steel, are not useful for СF…
CFD prediction of bubble behavior in two-dimensional gas-solid fluidized beds
2009
This work focuses on the computational fluid dynamics (CFD) simulation of a laboratory-scale, two-dimensional fluidized bed and the relevant experiments in order to validate the prediction capability of the adopted codes and models. Both experimental and computational quantitative data were analyzed by means of an original digital image analysis technique, allowing for coherent comparison of computational and experimental results. In particular, this work analyzes the capability of the CFD simulations in predicting the fluctuating behavior of bubbling fluidized beds by means of frequency analysis of bubble-related phenomena.
Damage accumulation under variable amplitude loading of welded medium- and high-strength steels
2004
Abstract The paper presents the calculation of cumulative damage for two types of welded joints (butt weld and transverse stiffeners) of four steels (medium to high strength): S355N, S355M, S690Q and S960Q. This calculation is based on experimental data obtained under axial loading and bending with constant and variable amplitudes (Gaussian distribution and Gauss with overload spectrum). The experiments were performed under fully reversed ( R =−1) and pulsating ( R =0) loading. The fatigue life is calculated using the modifications of the Palmgren–Miner–Original rule, according to the Palmgren–Miner–Elementary method, as well as to Haibach’s suggestion. The fatigue life does not depend on t…
A theoretical and experimental study to point out the notion of loading mode in damage mechanicsApplication to the identification and validation of a…
2002
A model of fatigue-induced intralaminar cracking in strongly anisotropic laminates is presented. The features of the microscopic phenomenon are explicitly taken into account at the macroscopic level by the use of two variables, which define a new concept in Damage Mechanics that results not only in a coherent model of crack density evolution, but also in a coherent treatment of damage deactivation. Damage evolution indeed is strongly dependent on the local loading mode in each ply where cracking occurs. Experiments on complex lay-ups provided sufficient data for complete calibration of the model. These tests also allowed to validate the theoretical choice of the damage variable. Finally, nu…
Assessment of multiaxial fatigue behaviour of welded joints under combined bending and torsion by application of a fictitious notch radius
2004
Abstract A major problem in the assessment of the multiaxial fatigue behaviour in welded joints is the determination of local notch stresses, since the real local radii in most cases are not known. This can be circumvented by introducing a fictitious notch radius, according to Neuber and Radaj. The calculations of local equivalent stress amplitudes for welded joints (tube–tube and flange–tube) under pure bending, pure torsion and combined in- and out-of-phase bending with torsion can then be carried out by stress-based and strain energy density-based criteria. Among the investigated methods, the most reliable results are obtained with the effective equivalent stress hypothesis, an integral …
A critical plane approach based on energy concepts: application to biaxial random tension-compression high-cycle fatigue regime
1999
Abstract In this paper the energy parameter, defined for random loadings, is analysed. Under uniaxial loading this parameter distinguishes between the strain energy density for tension (positive) and the strain energy density for compression (negative). As a consequence, if there is no mean component in the random loading, we obtain a random history of strain (elastic and plastic) energy density with zero expected value. Under multiaxial loadings the normal strain energy density in the critical plane (i.e. the plane of the maximum damage) is understood as the energy parameter. The history of strain energy density is schematized with use of the rain-flow algorithm. Fatigue damage is accumula…