Search results for "Mold"
showing 10 items of 118 documents
Thermomechanical properties of radiation-modified blends of polyethylene with liquid crystalline copolyester
1999
The results of investigation of gamma irradiated blends of high-density polyethylene (PE) with thermotropic polymer liquid crystal (PLC) are presented. The PLC used was a copolyester of 40% poly(ethylene terephthalate) with 60% p-(hydroxy-benzoic acid). The PLC content in the blends was 0, 5, and 10 wt%. The constituents were blended with the use of a single screw extruder. The specimens were prepared by compression molding. The irradiation of the samples was performed by a Co 60 γ-radiation source in inert atmosphere (argon) up to absorbed relatively low doses (up to 200 kGy: 1 Mrad = 10 kGy). The morphological, thermal, and mechanical properties were investigated for irradiated and unirra…
Effect of the processing techniques on the properties of ecocomposites based on vegetable oil-derived Mater-Bi® and wood flour
2009
Polymer composites based on biodegradable polymers and natural-organic fillers are becoming more and more important because of their interesting properties in terms of environmental impact, manufacturing cost, and esthetic features. In particular, the use of biodegradable polymer matrices allows obtaining a full biodegradability. One of the most interesting biodegradable polymer families is the Mater-Bi® one. In this work, we investigated the processability, the influence of different processing techniques, and the influence of the filler particle size on the properties of Mater-Bi/wood flour composites. Injection molding caused a partial degradation of the macromolecular chains, whereas si…
Redesign of the Geometry of Parts Produced from PBT Composite to Improve Their Operational Behavior
2021
Parts produced from PBT-GF30 (70% polybutylene terephthalate +30% fiberglass) are very often used in car construction, due to the properties of this material. The current trend is to make parts with a shape designed to be as complex as possible, to take over many functions in operation. During the research, a part that is a component of the structure of car safety systems, and that must be completely reliable in operation, was analyzed. This piece has a complex shape that involves the intersection of several walls. Thus, the research aimed at establishing the optimal radius of connection between the walls (R), the ratio between the thickness of the intersecting walls (K) and the angle of in…
Combining carvacrol and nisin in biodegradable films for antibacterial packaging applications
2021
Abstract In this work, the feasibility of antibacterial biopolymeric films containing carvacrol (CRV) and a nisin commercial formulation (Nis) for potential food packaging applications was investigated. As polymer matrix, a commercial biodegradable polymer formulation of Mater-Bi (MB) was chosen due to its significant food packaging applications. CRV and Nis were chosen due to their well-established antibacterial properties and their potential synergistic effect. MB/CRV, MB/Nis, and MB/CRV/Nis systems were produced by melt mixing and compression molding. The mechanical properties of the films were evaluated by tensile tests. Differential scanning calorimetry was assessed aiming at investiga…
Effect of wetting agent coverage on the surface properties of resin composite submitted to brushing and staining cycles
2020
Background Wetting agents facilitate the composites handling, acting as a lubricant and decreasing their stickness to spatula. The effects of these materials on the properties of composites are not completely clear. This study aimed to evaluate Gloss, Color, Roughness and Microhardness of a composite (Filtek Z250 XT, 3M Oral Care) covered by a wetting agent (Modeling Resin, Bisco), submitted to brushing and staining cycles with red wine. Material and Methods Cylinder-shaped samples (8 mm ø x 2 mm height) were divided into 4 groups, according to application of wetting agent and brushing cycles (n = 20). The composite was placed in the orifice of a polytetrafluoroethylene mold, received wetti…
Estimation of the tensile strength of an oriented flax fiber-reinforced polymer composite
2011
Unidirectional orientation of natural fibers in a polymer composite ensures the highest efficiency of reinforcement. Flax fiber reinforcement is discontinuous due to limited fiber length and heterogeneous due to the presence of elementary fibers and their bundles. In order to assess the upper limit of tensile strength of such slightly misoriented, nominally UD natural fiber composite, a statistical strength model of continuous UD fiber reinforced composites is applied. It is found that the experimental strength of UD flax composites, produced from rovings or manually aligned fibers, approaches the theoretical limit only at relatively low fiber volume fraction ca. 0.2, being markedly below i…
Effect of some injection molding processing conditions on weld lines characteristics
1988
The influence of injection and mold temperature as well as holding time on the knit-line characteristics in samples of Nylon 6 obtained by injection molding was analysed. The characteristics of the surface defect seem to be governed by the shrinkage rate and amount in the weld line zone.
Potential of Antifungal Proteins (AFPs) to Control Penicillium Postharvest Fruit Decay
2021
Penicillium phytopathogenic species provoke severe postharvest disease and economic losses. Penicillium expansum is the main pome fruit phytopathogen while Penicillium digitatum and Penicillium italicum cause citrus green and blue mold, respectively. Control strategies rely on the use of synthetic fungicides, but the appearance of resistant strains and safety concerns have led to the search for new antifungals. Here, the potential application of different antifungal proteins (AFPs) including the three Penicillium chrysogenum proteins (PAF, PAFB and PAFC), as well as the Neosartorya fischeri NFAP2 protein to control Penicillium decay, has been evaluated. PAFB was the most potent AFP against …
Analysis of gas sensors array signals for evaluation of mold contamination in buildings
2018
Mold is considered to be one of the most important features of Sick Building Syndrome (SBS) and is an important problem in building sector. In numerous cases it is caused by the rising moisture of building envelopes and overstated humidity of indoor air. Fungal contamination is normally evaluated using standard biological methods which are time-consuming and require a lot of manual labor. But also, fungi emit Volatile Organic Compounds (VOC) that can be detected in the indoor air using several techniques of detection e.g. chromatography. VOCs can be also detected using gas sensors arrays. All arrays of sensors generate particular electric signals that ought to be analyzed using statistical …
Injection moldability and properties of compatibilized PA6/LDPE blends
2004
An ethylene-acrylic acid copolymer (EAA), either alone or combined with a low molar mass bis-oxazoline compound (PBO), has been used as a compatibilization promoter for blends of polyamide-6 (PA6) with low-density polyethylene (LDPE). The effect of compatibilization on blend processability in injection molding operations and on the properties of the molded specimens has been studied. In the absence of compatibilization, the injection molded articles were shown to have low-quality surface appearance and poor mechanical properties. Both these characteristics were appreciably improved as a result of reactive compatibilization of the blends with EAA and, even more, with the EAA-PBO couple. In f…